Planet WNAP-W2200UE User manual

300Mbps 802.11n
In-Wall Wireless AP
w/ USB Charger
WNAP-W2200UE

I
Copyright
Copyright  2018 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no r epresentations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting
from any defect in the software. Further, PLANET reserves the right to revise this publication and to
make changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a r esidential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a p articular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired
operation.

I
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
CE Compliance Statement
This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general
public to electromagnetic fields by way of health protection. The device complies with RF
specifications when it is used at a safe distance of 20 cm from your body.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following the EU
directive 2014/53/EU) without any limitation except for the countries mentioned below:
Country Restriction Reasons/remarks
Bulgaria None General authorization required for outdoor use and
public service
France
Outdoor use;
limited to 10
mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy None If used outside of own premises, general authorization is
required
Luxembourg None General authorization required for network and service
supply(not for spectrum)
Norway Implemented This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Russian
Federation
None Only for indoor applications
Note: Please don’t use the product outdoors in France.
WEEE regulation
To avoid the potential effects on t he environment and human health as a r esult of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.

II
Revision
User Manual of PLANET 300Mbps 802.11n In-Wall Wireless Access Point w/ USB Charger
Model: WNAP-W2200UE
Rev: 1.0 (October, 2018)
Part No. EM-WNAP-W2200UE_v1.0

III
CONTENTS
Chapter 1.Product Introduction...........................................................................................................1
Package Contents...............................................................................................................11.1
Product Description............................................................................................................21.2
Product Features.................................................................................................................51.3
Product Specifications.......................................................................................................61.4
Chapter 2.Hardware Installation..........................................................................................................8
Product Outlook..................................................................................................................82.1
Chapter 3.Connecting to the AP........................................................................................................11
System Requirements ......................................................................................................113.1
Installing the AP ................................................................................................................113.2
Chapter 4.Quick Installation Guide ...................................................................................................13
Manual Network Setup -- TCP/IP Configuration.............................................................134.1
4.1.1 Configuring the IP Address Manually.................................................................13
Starting Setup in the Web UI............................................................................................174.2
Chapter 5.Configuring the AP............................................................................................................18
Wizard.................................................................................................................................195.1
Gateway Mode (Router)....................................................................................................205.2
5.2.1 WAN Settings ........................................................................................................21
5.2.2 Wireless.................................................................................................................22
Repeater Mode (Universal Repeater) ..............................................................................235.3
AP Mode.............................................................................................................................265.4
Super WDS Mode (WDS Bridge in PtP/PtMP).................................................................285.5
Advanced ...........................................................................................................................305.6
5.6.1 Device Status ........................................................................................................30
5.6.2 Wireless .................................................................................................................32
5.6.3 Network..................................................................................................................36
5.6.4 Management..........................................................................................................37
Chapter 6.Quick Connection to a Wireless Network.......................................................................41
Windows XP (Wireless Zero Configuration)...................................................................416.1
Windows 7 (WLAN AutoConfig).......................................................................................436.2
Mac OS X 10.x....................................................................................................................466.3
iPhone/iPod Touch/iPad ...................................................................................................516.4
Appendix A: Planet Smart Discovery Utility.....................................................................................55
Appendix B: FAQs...............................................................................................................................56

IV
Q1: How to Set Up the AP Client Connection..........................................................................56
Q2: How to Set Up the WDS Connection .................................................................................61
Appendix B: Troubleshooting............................................................................................................65
Appendix C: Glossary.........................................................................................................................67

V
FIGURE
FIGURE 2-1 WNAP-W2200UETRIPLE VIEW.........................................................................................................8
FIGURE 2-2 WNAP-W2200UE FRONT PANEL........................................................................................................9
FIGURE 2-3 WNAP-W2200UE REAR PANEL .........................................................................................................9
FIGURE 3-1 TAKING THE COVER OFF .....................................................................................................................11
FIGURE 3-2 CONNECTING THE ETHERNET CABLE .................................................................................................12
FIGURE 3-3 CONNECTING THE LAPTOP OR CHARGING DEVICE .............................................................................12
FIGURE 4-1 TCP/IP SETTING................................................................................................................................14
FIGURE 4-2 WINDOWS START MENU ....................................................................................................................15
FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND .........................................................................................15
FIGURE 4-4 FAILED RESULT OF PING COMMAND ..................................................................................................16
FIGURE 4-5 LOGIN BY DEFAULT IPADDRESS........................................................................................................17
FIGURE 4-6 LOGIN WINDOW ................................................................................................................................17
FIGURE 5-1 MAIN MENU ......................................................................................................................................18
FIGURE 5-2 OPERATION MODE .............................................................................................................................19
FIGURE 5-3 GATEWAY MODE................................................................................................................................20
FIGURE 5-4 GATEWAY -- STATIC IP .......................................................................................................................21
FIGURE 5-5 GATEWAY –PPPOE(ADSL)..............................................................................................................21
FIGURE 5-6 GATEWAY –DHCP.............................................................................................................................22
FIGURE 5-7 GATEWAY –WIRELESS .......................................................................................................................22
FIGURE 5-8 REPEATER MODE ...............................................................................................................................23
FIGURE 5-9 REPEATER MODE -- SCAN AP ............................................................................................................24
FIGURE 5-10 REPEATER MODE -- SELECT AP .......................................................................................................25
FIGURE 5-11 AP MODE.........................................................................................................................................26
FIGURE 5-12AP MODE -- LAN ............................................................................................................................27
FIGURE 5-13 SUPER WDS MODE..........................................................................................................................28
FIGURE 5-14 SUPER WDS MODE –AP1...............................................................................................................29
FIGURE 5-15 SUPER WDS MODE –AP2...............................................................................................................29
FIGURE 5-16 ADVANCED ......................................................................................................................................30
FIGURE 5-17 STATUS ............................................................................................................................................30
FIGURE 5-18WIRELESS STATUS ...........................................................................................................................31
FIGURE 5-19 LAN STATUS ...................................................................................................................................31
FIGURE 5-20 BASIC SETTINGS ..............................................................................................................................32
FIGURE 5-21VIRTUAL AP ....................................................................................................................................33
FIGURE 5-22ACCESS CONTROL -ACCESS ALL.....................................................................................................33
FIGURE 5-23ACCESS CONTROL –ALLOW LISTED ................................................................................................34
FIGURE 5-24ADVANCED SETTINGS ......................................................................................................................34
FIGURE 5-25 LAN SETTINGS................................................................................................................................36
FIGURE 5-26VLAN .............................................................................................................................................36
FIGURE 5-27 SNMP .............................................................................................................................................37
FIGURE 5-28 SYSTEM TIME ..................................................................................................................................37
FIGURE 5-29 LOGS ...............................................................................................................................................38
FIGURE 5-30 UPGRADING FIRMWARE ...................................................................................................................39

VI
FIGURE 5-31 SYSTEM ...........................................................................................................................................40
FIGURE 5-32 USER................................................................................................................................................40
FIGURE 6-1 SYSTEM TRAY –WIRELESS NETWORK ICON......................................................................................41
FIGURE 6-2 CHOOSING AWIRELESS NETWORK ....................................................................................................41
FIGURE 6-3 ENTERING THE NETWORK KEY..........................................................................................................42
FIGURE 6-4 CHOOSING AWIRELESS NETWORK -- CONNECTED ............................................................................42
FIGURE 6-5 NETWORK ICON.................................................................................................................................43
FIGURE 6-6 WLAN AUTOCONFIG ........................................................................................................................43
FIGURE 6-7 TYPING THE NETWORK KEY ..............................................................................................................44
FIGURE 6-8 CONNECTING TO A NETWORK ............................................................................................................44
FIGURE 6-9 CONNECTED TO A NETWORK..............................................................................................................45
FIGURE 6-10 MAC OS –NETWORK ICON..............................................................................................................46
FIGURE 6-11 HIGHLIGHTING AND SELECTING THE WIRELESS NETWORK..............................................................46
FIGURE 6-12 ENTERING THE PASSWORD...............................................................................................................47
FIGURE 6-13 CONNECTED TO THE NETWORK .......................................................................................................48
FIGURE 6-14 SYSTEM PREFERENCES ....................................................................................................................49
FIGURE 6-15 SYSTEM PREFERENCES -- NETWORK................................................................................................49
FIGURE 6-16 SELECTING THE WIRELESS NETWORK .............................................................................................50
FIGURE 6-17 IPHONE –SETTINGS ICON.................................................................................................................51
FIGURE 6-18WI-FI SETTING ................................................................................................................................51
FIGURE 6-19WI-FI SETTING –NOT CONNECTED .................................................................................................52
FIGURE 6-20TURNING ON WI-FI..........................................................................................................................52
FIGURE 6-21 IPHONE -- ENTERING THE PASSWORD...............................................................................................53
FIGURE 6-22 IPHONE -- CONNECTED TO THE NETWORK .......................................................................................54

User Manual of WNAP-W2200UE
-1-
Chapter 1. Product Introduction
Package Contents1.1
Thank you for choosing PLANET WNAP-W2200UE Wireless AP. Please verify the contents inside the package
box.
Package Contents of WNAP-W2200UE
WNAP-W2200UE Quick Guide Screw x 2
If there is any item missing or damaged, please contact the seller immediately.

User Manual of WNAP-W2200UE
-2-
Product Description1.2
All-in-One Manageable Wi-Fi Solution for Hotel Industry
PLANET WNAP-W2200UE enables the hospitality industry to build a high-speed wireless network with 802.1Q
VLAN and PLANET AP controller. Furthermore, it conforms to standard 86-type electrical junction box and
IEEE 802.3af/at+, suitable for in-wall installation enabling to integrate the hotel network with its all-in-one
interface. The WNAP-W2200UE also provides stable wireless signal that makes access to internet viable in
regard to whatever nature of work you are into.
Easy Deployment with PLANET AP Controller
To expand the capability of in-wall AP, PLANET WNAP-W2200UE comes with centralized management,
enabling the hospitality industry to deploy multiple APs with a single interface of AP controller and reducing
repetitive tasks including AP provisioning, AP status monitoring and AP maintenance. In addition, by
connecting with PLANET AP controller, PLANET WNAP-W2200UE helps hoteliers optimize their wireless
network within minutes.

User Manual of WNAP-W2200UE
-3-
Suitable for Any Room Installation without Spoiling Interior Design
Featuring attractive in-wall design, the WNAP-W2200UE can be firmly installed into the wall via the standard 86
x 86 m m European outlet box, which makes electrical wiring invisible and convenient for room installation
without affecting the original interior design. It is ideal for hotels, residences, hospitals and more to establish any
kind of wireless network.
Comprehensive Wireless Operation Modes
The WNAP-W2200UE supports multiple wireless communication connectivities such as AP, Gateway (Router),
Repeater, WDS Point-to-Point (PtP) and WDS Point-to-Multipoint (PtMP), allowing users to comprehensively
experience various applications.

User Manual of WNAP-W2200UE
-4-
Easy to Use Wi-Fi and USB Charger
Having a good night sleep is what we need in the hotel. It is easy to disable the Wi-Fi signal and LED on the front
panel of the WNAP-W2200UE. When you don’t need to use wireless LAN, just press the button to close the
Wi-Fi and LE D. To provide better services for travelers, the WNAP-W2200UE comes with a built-in USB 2.0
charger whose output of 5V DC power can charge any USB compliant mobile devices, e.g., cell phones, iPads,
and other handheld devices. Thus, the WNAP-W2200 brings convenience to pedestrians, travelers and other
users without having to worry about forgetting to carry an AC adapter.

User Manual of WNAP-W2200UE
-5-
Product Features1.3
 Standard Compliant Hardware Interface
 Compliant with IEEE 802.11n wireless technology with data rate of up to 300Mbps
 One 10/100BASE-TX port and one PoE powered device (PD) port
 USB charger port for charging most of mobile devices easily
 European 86-type wall outlet compatibility
 Secure Network Connection
 Advanced security: 64-/128-bit WEP, WPA/WPA2 and WPA-PSK/WPA2-PSK (TKIP/AES
encryption), 802.1x
 Supports wireless MAC address filtering control to limit the connected wireless clients
 Supports 802.1Q VLAN and SSID-to-VLAN mapping
 Supports IP/Port/MAC address/URL filtering, DoS, SPI Firewall
 Supports DMZ and port forwarding
 Bandwidth control per IP address to increase network stability
 Multiple Operation Modes and Wireless Features
 Multiple operation modes: AP, Gateway, Repeater, WDS
 WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless
 Coverage threshold to limit the weak signal of clients occupying session
 Real-time Wi-Fi channel analysis chart and client limit control for better performance
 Easy Deployment and Management
 Supports PLANET AP Controllers in AP mode
 Easy discovery by PLANET Smart Discovery
 Self-healing mechanism through system auto reboot setting
 System status monitoring through remote Syslog Server
 Supports PLANET DDNS/Easy DDNS

User Manual of WNAP-W2200UE
-6-
Product Specifications1.4
Product WNAP-W2200UE
300Mbps 802.11n In-Wall Wireless Access Point with USB Charger
Hardware Specifications
Interfaces
LAN 1 x 10/100BASE-TX RJ45 port
Auto-negotiation and auto MDI/MDI-X
PoE Port
1 x 10/100Mbps auto MDI/MDI-X RJ45 port (rear panel)
※ IEEE 802.3af/at PD port
USB Port USB 2.0, Type A, 5V DC, 0.5A output
Antennas Gain 2 x 2dBi antenna
Button Reset button (Press over 15
seconds to reset the device to the factory
default)
LED Indicators Wireless
Dimensions (Φ x H) 86 x 35 x 86 mm
Weight 106 ±5g
Power Requirements 48V 0.5A, IEEE 802.3af/at PoE+
Power Consumption < 5W
Mounting
In-wall mount
Wireless Interface Specifications
Standard IEEE 802.11b/g/n 2.4GHz
Media Access Control CSMA/CA
Data Modulation
Transmission/emission type: DSSS/OFDM
Data modulation type: OFDM: BPSK, QPSK, 16-QAM, 64-
QAM, DBPSK,
DQPSK, CCK
Frequency Range FCC: 2.412~2.462GHz
ETSI: 2.412~2.472GHz
Operating Channels FCC: 1~11
ETSI: 1~13
RF Power < 20dBm (EIRP)
Receive Sensitivity
Network Mode Data Rate Receive Sensitivity (dBm)
2.4GHz
802.11b 1Mbps -88
11Mbps -85
802.11g 6Mbps -88
54Mbps -68
802.11n MCS0/MCS8 -68
MCS7/MCS15 -68
Software Features
LAN Static IP
Supports IP-MAC binding

User Manual of WNAP-W2200UE
-7-
Wireless Mode
Access Point
Gateway
Repeater
WDS
Channel Width 20MHz, 40MHz,
Encryption Security 64-/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Wireless Security
Enable/Disable SSID Broadcast
Wireless MAC address filtering
User Isolation
Max. SSIDs 4
Max. Clients 64 (20 is suggested, depending on usage)
Max. WDS Peers 4
Wireless QoS Supports Wi-Fi Multimedia (WMM)
Wireless Advanced
Auto channel selection
5-level transmit power control (100%, 75%, 50%, 25%, 12.5%)
Client limit control, coverage threshold
Wi-Fi channel analysis chart
Status Monitoring
Device status, wireless client list
PLANET Smart Discovery
DHCP client table
System Log supports remote syslog server
VLAN IEEE 802.1Q VLAN (VID: 3~4094)
SSID-to-VLAN mapping to up to 4 SSIDs
Self-healing Supports auto reboot settings per day/hour
System Management
Supports PLANET Hardware AP Controller/ Software AP Controller
Applicable controllers: WAPC-500, WAPC-1000, and SAPC
Remote management through PLANET DDNS/Easy DDNS
Configuration backup and restore
Supports UPnP and IGMP Proxy
Supports PPTP/L2TP/IPSec VPN pass-through
SNMP v1/v2c/v3 support, MIB I/II, Private MIB
Environment & Certification
Temperature Operating: -20 ~ 55 degrees C
Storage: -40 ~ 70 degrees C
Humidity Operating: 10 ~ 90% (non-condensing)
Storage: 5 ~ 95% (non-condensing)
Regulatory CE, RoHS
Fast Roaming

User Manual of WNAP-W2200UE
-8-
Chapter 2. Hardware Installation
Product Outlook2.1
WNAP-W2200UE
 Dimensions: 86 x 35 x 86 mm (W x D x H)
 Weight: 106 ±5g
 Triple View
Figure 2-1 WNAP-W2200UE Triple View

User Manual of WNAP-W2200UE
-9-
 Front Panel
Figure 2-2 WNAP-W2200UE Front Panel
 Rear Panel
Figure 2-3 WNAP-W2200UE Rear Panel

User Manual of WNAP-W2200UE
-10-
 LED
LED State Description
Wi-Fi On The LED indicates green color
 Button definition
Object
Description
Wi-Fi Press the button for one second to turn Wi-Fi on or off
Reset Press the Reset button for over 15 seconds and then release it to restore
system to the factory default settings.
 H/W Interface
Object
Description
PoE Port
(802.3af/at PoE+)
10/100bps RJ45 port, auto MDI/ MDI-X
Connect PoE port to the IEEE 802.3af/at PoE+ switch to power on the device.
LAN Port 10/100Mbps RJ-45 port, auto MDI/ MDI-X
Connect this port to the network equipment.
USB Port USB 2.0, Type A, 5V DC/0.5A output
Connect this port to charge the mobile device.

User Manual of WNAP-W2200UE
-11-
Chapter 3.Connecting to the AP
System Requirements3.1
 Broadband Internet Access Service (Cable/xDSL/Ethernet connection)
 One IEEE 802.3at PoE switch (supply power to the WNAP-W2200UE)
 PCs with a working Ethernet adapter and an Ethernet cable with RJ45 connectors
 PCs running Windows 98/ME, NT4.0, 2000/XP, Windows Vista / Win 7, MAC OS 9 or later, Linux,
UNIX or other platforms compatible with TCP/IP protocols
1. The AP in the following instructions refers to PLANET WNAP-W2200UE.
2. It is recommended to use Internet Explorer 11, Firefox or Chrome to access the AP.
Installing the AP3.2
Before installing the AP, make sure your PoE switch is connected to the Internet through the broadband service
successfully at this moment. If there is any problem, please contact your local ISP.
Step 1.Follow the figure below to install the WNAP-W2200UE.
Use the flat-blade screwdriver to take the cover of the WNAP-W2200UE off.
Figure 3-1 Taking the Cover Off

User Manual of WNAP-W2200UE
-12-
Step 2.Follow the figure below to install the WNAP-W2200UE.
Figure 3-2 Connecting the Ethernet cable
Step 3.Follow the figure below to connect the network devices.
Figure 3-3 Connecting the Laptop or Charging Device