Planika PrimeFire 4 User manual

Copyright 2017 Planika Sp. z o.o. www.planikafires.com i1086#0 18.10.2017 1
C
B
x 1
D
x 1 x 1
A
x 1
H2H1
H
L
D
L2L2 L1
START
STOP
READYFUELHOT
ERROR
PAT. PEND.
ECO
Planika
I N T E L L I G E N T F I R E
INSTALLATION MANUAL
PrimeFire#4
PrimeFire#4 REMOTE
Manufactured by:
Planika Sp. z o.o.
ul. Bydgoska 38
86-06 Brzoza
Poland
[mm]
[
‘’
]
H
139
5
1
/
2
H1
137
5
3
/
8
H2
2
1
/
16
L
700
27
9
/
16
L
1
500
19
11
/
16
L2
100
3
15
/
16
D
2 5
9
5
/
8
Fixed unit’s weight
= 15 kg / 33,07 lb
Automatic fuel pump
SERVICE KIT
*
* only REMOTE

Copyright 2017 Planika Sp. z o.o. www.planikafires.com i1086#0 18.10.2017 2
• Do not install the device in areas with a capacity of less than 58 m
3
/ 2.049 ft
3
(22 m
2
/ 240 ft
2
with
a height of 2.6 m / 8.5 ft).
• While installing the device according to the instruction manual local and national guidelines are
to be observed.
• Place the device on a levelled surface. The cavity for the fireplace has to be designed with the
use of a spirit level.
• It is not permitted to use the fireplace that is not placed in a housing. The cavity has to be
designed according to the guidelines and dimensions in the instruction manual. If the cavity has
different dimensions it has to be adjusted in such a way that it complies with the guidelines
stated in the installation manual.
• Do not obstruct the ventilation slots and/or ventilators.
• Do not place any decorative elements on the device.
• Do not install the device in areas of large drafts of air, near fans, vents, etc.
• Do not place in areas where there might be a potentially explosive atmosphere of paint vapours,
industrial dusts, etc.
• No flammable items should be placed in direct contact and within a radius of 1 m / .28 ft around
the device. Do not place near curtains, net curtains, etc.
• Do not expose the device to weather conditions. The product is for internal use only.
• Do not expose the device to meteorological conditions. The device is for indoor use only.
• Do not place the device in close proximity to sources of humidity.
• It is obligatory to have a carbon-dioxide (CO
2
) or dry chemical extinguisher placed nearby the
device.
• Installation of the device must provide an easy removal of the device for service.
• The room in which the device will be installed must have efficient ventilation to ensure air
exchange in the room at least once per hour.
• Do not start the device before a complete and proper installation.
• Do not fill the fuel container before placing the product into its final position.
• In case of mounting more than one unit in the room, the minimal cubature is the sum of
cubatures required for each unit.
• The recess, into which the fireplace will be mounted, has to have a load capacity of 22,5 kg
(49,6lb).
• Device must be kept out of reach of children, animals and unauthorized persons.
• Do not install the device on a mobile object (eg. caravan, yacht ).
!

Copyright 2017 Planika Sp. z o.o. www.planikafires.com i1086#0 18.10.2017 3
INSTALLATION
ATTENTION! If you have purchased the original steel casing for the device, please follow the
instruction manual provided for the casing and skip the procedure described below.
− Place the device in a housing that is closely connected to the construction of the building.
− The elements of construction over the furnace must be made of non-flammable materials.
− Recess, what will be done below the grate fireplace must be sealed.
− Supply the housing with a loose cable min. 3 x ,75 mm
2
, with power supply 23 V, 5 Hz, to connect
the device to the mains.
− If there is going to be a cover over the furnace, it must be made of non-flammable materials and the
minimum distance from the furnace must be kept - not less than 35 cm/ 13 ¾ in.
− It is not allowed to use a device before placing it into a prepared wall recess or other housing/cavity.
min 1000 mm
min 39
3
8 "
min 1500 mm
min 59
1
16
"
min 1000 mm
min 39
3
8 "
min 1000 mm
min 39
3
8
"
min. 50 mm
min. 1
15
16 "
min. 50 mm
min. 1
15
16 "
Due to fire safety, it is forbidden to place any flammable
materials within a 1 m (40 inches) radius from the fireplace.
Also, Planika does not recommend to place any heat
sensiti e materials or de ices within this radius as it can
significantly limit the materials properties and longe ity.
Planika will not take any responsibility for the damage of any
materials or de ices being installed abo e the fireplace.
Non-flammable
materials
Non-
flammable
materials
Device cannot be installed
in a two-way open setting.

Copyright 2017 Planika Sp. z o.o. www.planikafires.com i1086#0 18.10.2017
How to self-make the housing for the device.
Make a cavity for the insert following the diagram below. Making the cavity make sure that the plane on which
you are going to set the furnace inset is well levelled, as later it will not be possible to level the insert.
min 150 mm
min 5 78 "
700 mm / 27 916 "
680 mm / 26 34 "
2 mm
116 "
min 710 mm / min 27
15
16
"
230 mm
9
1
16
"
680 mm
26
34
"
230 mm
9
1
16
"
min 150 mm
min 5
78
"
680 mm / 26
34
"
min 255 mm
min 10
116
"
min 12 mm
min
12
"
min 13 mm
min
12
"
min 350 mm
min 13
34
"
B
A
A-A
min 710 mm
min 27
1516
"
B-B
min 13 mm
min
12
"
min 12 mm
min
12
"
min 255
min 10
116
"

Copyright 2017 Planika Sp. z o.o. www.planikafires.com i1086#0 18.10.2017 5
The difference in level between the ends of the furnace must not exceed 2 mm. Poor levelling may cause
abnormal operation of the device and, in extreme cases, it can cause leaks of the Fanola ® liquid and the
danger of fire.
Then connect the supplied cable with a connection block at the end of the cord. Note that connection to the
mains must be made by a qualified electrician. The furnace assembly "A" is connected to mains now. Set it
in the prepared cavity.
Level the surface of the cavity.
The deviation cannot exceed
2 mm (1/16 in)
Connection to the mains must be
made by a qualified electrician.

Copyright 2017 Planika Sp. z o.o. www.planikafires.com i1086#0 18.10.2017 6
WARNING !!!
• Make sure that the device has been correctly installed and read the attached instruction manual.
• You are not allowed to fill the fuel tank and start the device before having read the instruction manual.
• If in the future it is necessary to take the device out of the housing, wait until the fuel has burned-up
completely and the display shows , disconnect the power supply and take the device out of
the housing.
• Keep this instruction manual throughout the lifetime of the device.
FUEL