Plantronics DuoSet H141 User manual

User Guide
DuoSet™ Headset
Models H141/H141N/P141
Duoset English 4.0 10/27/99 3:58 PM Page 4

WELCOME
Thank you for selecting the DuoSet™
Headset from Plantronics. This User
Guide will help you install your
DuoSet™ Headset and learn its basic
operation. The Amplifier is
described in a separate guide
which should be read following
familiarization with the headset.
Duoset English 4.0 10/27/99 3:59 PM Page 11

1
A B C
DEF
GHI
JK
Duoset English 4.0 10/27/99 3:59 PM Page 5

7
1
4
6
5
8
3
2
2
7
1
4
6
5
8
3
2
DIAGRAM
Duoset English 4.0 10/27/99 3:59 PM Page 6

3
Adjustable Headband
(P/N 43298-01)
Ear Cushion Assembly
(P/N 43299-01)
Headset Assembly
Voice Boom
Cord
Clothing Clip
(P/N 43220-01)
Pivot Ball Ring
(P/N 45650-01)
Flexible Earhook
(P/N 45651-01)
3
6
5
1
2
4
7
Headset
(Both Configurations Shown)
8
DIAGRAM KEY
Duoset English 4.0 10/27/99 3:59 PM Page 7

5
OVER-THE-EAR-CONFIGURATION
If already in place, unsnap the Headband from the rear of
the Headset Assembly .
If already in place, remove the Ear Cushion and
Rubber Ring from the Headset Assembly .
Press the Pivot Ball Ring onto the Headset Assembly
aligning the Pivot Ball Ring with the Voice Boom .
Insert the Earhook into either side of the Pivot Ball Ring ,
depending on whether the headset is to be worn over the left
or the right ear.
For added stability, press the Headset Cord under the
Cord Guides on the Earhook.
Expand the Earhook around your ear as shown and release.
Rotating the Pivot Ball Ring on the Headset Assembly
may provide a better fit.
3
7
5
7
8
4
3
7
3
2
3
1
B
A
A
B
C
D
Duoset English 4.0 10/27/99 3:59 PM Page 12

6
OVER-THE-HEAD CONFIGURATION
If already in place, remove the Pivot Ball Ring and
Earhook .
Press the Ear Cushion and Rubber Ring onto the Headset
Assembly . Align the notch in the ring with the Voice
Boom .
Snap the ball on the end of the Headband into the socket
on the rear of the Headset Assembly .
Place the Headband over the top of your head, with the
Ear Cushion resting gently against your ear and the T-Bar
positioned above the opposite ear.
If the headband is too tight or too loose, grasp the metal part
of headband and gently bend in the middle. The headband
length may be adjusted for fit and comfort.
2
1
3
1
4
3
2
8
7
A
F
B
A
E
Duoset English 4.0 10/27/99 3:59 PM Page 13

7
POSITIONING THE BOOM
If you have the Voice Tube version of the product, pull-out,
push-in, rotate, or swivel the Voice Boom into a position
near the corner of your mouth that best transmits your voice.
If you have the Noise-Canceling version of the product,
position the tip of the Voice Boom as near to the corner of
your mouth as you comfortably can.
4
4
G
H
Duoset English 4.0 10/27/99 3:59 PM Page 14

8
SECURING THE HEADSET
Attach the Clothing Clip at about chest level. The clip keeps
the headset properly seated and free of the weight of the
Headset Cable . This is particularly important in the Earhook
configuration.
5
6
I
Duoset English 4.0 10/27/99 3:59 PM Page 15

9
Using the Quick Disconnect™Module
Use the Quick Disconnect™(QD) Module to place a call
on hold and move away from the phone without removing
the headset.
To put your call on hold, grasp the QD Module as shown and
pull straight apart.
To resume your conversation, reconnect the two halves.
Polaris™Headset Variations
Polaris™Headset Variations, designed for use with phones
with a clearly marked headset jack, do not require an
Amplifier. Insert the Polaris connector directly into the
headset jack. Consult your telephone's instruction manual
for more information.
For Non-Polaris™Versions
You are now ready to install the Amplifier.
CONNECTING THE HEADSET
J
K
Duoset English 4.0 10/27/99 3:59 PM Page 16