Plantronics Voyager 510S User manual

5 Easy Steps
The fastest way to set up your Plantronics
Voyager™510S Oce Headset System with
your desk phone and Bluetooth®mobile phone
Plantronics Voyager 510S Setup Guide
Base Power
Adapter
Voyager 510S
Headset Base
Voyager 510S
Headset
HL10
Automatic
Handset Lifter*
*Not included in all congurations

2Plantronics Voyager 510SSetup Guide
Headset Base with Pre-
installed Phone Cable
Base Power Adapter
5 Easy Steps
The fastest way to set up your
Voyager 510S Oce Headset System with your
desk phone and Bluetooth mobile phone
Voyage r 5 10S Series Setup Guide
BasePower
Adapter
Voyager510S
HeadsetBase
Voyager510S
Headsetwith Eartip
HL10
Automatic
HandsetLifter*
*Notinclud ed in all congurations
Setup Guide
HL10 Automatic
Handset Lifter HL10
User Guide
Plantronics Voyager 510s Package contents
Voyager 510SL With Automatic Handset Lifter* Adds:
Extender
Arm
Ringer
Microphone
Adapter for
Nortel i2004
Phones
HL10 Additional Parts Kit (if needed)
Please refer to the separate Safety Instructions for important product safety information prior
to installation or use of the product.
*Automatic Handset Lifter is bundled with certain Voyager 510S congurations and also available separately.
Eartips
Headset Travel Charger
Voyager 510SL+ Adds:
Online
Indicator
Light
Car
Lighter
Adapter
USB
Headset
Charger
Belt Clip
Carry Pouch
Accessories are available separately.
Headset

3
Questions? For fast, efficient Technical Support call: 800-544-4660 Ext. 5538
Fit the Headset
Slide the headset over and behind your ear, then press gently toward your ear. Rotate the
microphone boom until it is pointed toward your mouth. If the eartip is uncomfortable,
install a dierent eartip. See below.
To Convert for Wearing on Left Ear
A. Rotate microphone
boom up
B. Turn microphone
boom around
C. Rotate microphone
boom down
install eartiP & adjust fit
S T E P
1
For your safety and comfort, the eartip should never be inserted into the ear canal.
Choose the size and style of
eartip that ts most comfort-
ably. Align eartip tabs with
notches in headset.
Push in rmly and
twist counter
clockwise.
To Install a Dierent Eartip
Remove the pre-installed eartip by
pushing in and turning the eartip
clockwise, then pull rmly.
Note: For gel tips, ensure the raised part of the
eartip is pointed towards the curved section
of the headset as shown..

4Plantronics Voyager 510SSetup Guide
S T E P
2connect Base to desk Phone
Use Conguration A if:
You will use the Automatic Handset Lifter
or…
Your phone does NOT have built-in headset functionality (no Headset button).
Conguration A
2. Plug the short black Phone Cable that
is pre-installed on the Headset Base into
the now-open handset port [A] on the
desk phone.
1. Unplug the handset coil
cord from the desk phone
handset port [A], then plug it
into the handset port [B] on the
Headset Base.
A
A
Handset
Coil Cord Handset
Headset Base
(bottom view)
B
It is important for correct and safe operation that the base cord is installed into the proper jack of
your telephone. Follow these instructions carefully, especially if your telephone has two jacks where
the handset was attached. Be sure to note or mark which jack was used for the handset.

5
Questions? For fast, efficient Technical Support call: 800-544-4660 Ext. 5538
Use Conguration B if:
You will NOT use the Automatic Handset Lifter
and…
Your phone has built-in headset functionality (a Headset button).
HANDSET port or HEADSET port?
You should only use the headset port if you will not be using the Automatic Handset
Lifter and you have a pre-programmed Headset button on your phone.
In this conguration you must press both the Headset button on your phone
and the Call Control Button on the headset to answer/end calls.
1. Plug the short BLACK Phone
Cable that is pre-installed on
the Headset Base into the
Headset port [C] on the
desk phone.
Conrm there is
a “HEADSET” button
on your phone
Conguration B
C
Headset Base
(bottom view)

6Plantronics Voyager 510SSetup Guide
connect Power and charge headset
3
S T E P
Insert into yellow labeled power
connection on Headset Base as
shown to charge.
Headset Base
(bottom view)
Base
Power
Adapter
1. Plug the Base Power Adapter into a wall outlet, then plug the power cord into the yellow
labeled connector on the bottom of the Headset Base. The red Power light on the left
front of the Headset Base will turn on. (See illustration at bottom of page.)
A. Connect Headset Base to power outlet
1. Gently push the headset into the charging cradle as shown below. The amber Charge Status
light on the base will ash to indicate the headset battery is charging. A solid light indicates
full charge. A full charge will take approximately 3 hours.
B. Charge the Headset for at least 20 Minutes before using
The headset may also be charged directly with the
Headset Travel Charger. Plug the headset travel charger
into a wall outlet, then plug the power cord from the
adapter into the headset. The indicator light will ash
red while the headset battery is charging. The light will
change to solid blue when the battery is fully charged.
Power
(Red)
Charge Status
(AmbeR)

7
Questions? For fast, efficient Technical Support call: 800-544-4660 Ext. 5538
Why use a handset lifter? The lifter greatly simplies using
a headset with your desk phone. It lets you answer and
end calls without being near your phone.
install automatic handset lifter
4
S T E P
firmly press Lifter power
cord into red labeled port
on Headset Base.
Automatic
Handset Lifter
Headset Base
(bottom view)
The HL10™ Automatic Handset Lifter is included with certain Voyager 510S congurations
and is also available separately. See www.plantronics.com/Voyager510S for a complete
list of accessories.
1. Verify that the base-to-desk phone cable is connected to the handset port of the desk
phone, and not the headset port (Refer to Step 2, Conguration A).
2. firmly press the Handset Lifter power cord into the red labeled port to ensure a
complete connection.
A. Connect Handset Lifter power cord to Headset Base

8Plantronics Voyager 510SSetup Guide
4. Slide the Handset Lifter Arm under the handset until the lifter base touches
the side of the phone.
5. Slide the Lifter up to where it nearly touches the handset earpiece and hold.
Slide Lifter under
handset, then up
toward the ear piece
B. Determine Lifter position and height setting
Lifter viewed
from back Start with Lifter
Height Switch in
lowest position
Handset Lifter Arm
To determine the lifter position and height setting, you will rst need to power the
headset on and t the headset.
1. Press and hold the power/mute button on the headset for 3 seconds until the status
indicator ashes blue.
2. Fit the headset over and behind your ear as described on page 3.
3. Set the Lifter Height Switch to the lowest setting.
Status Indicator
Power/Mute
Button

9
Questions? For fast, efficient Technical Support call: 800-544-4660 Ext. 5538
6. With the other hand, press the Call Control Button on the headset.
This will activate the Handset Lifter and lift the handset from the phone.
If you hear a dial tone, the lifter height is set correctly and needs no adjustment. Press the Call
Control Button to return the handset to the cradle. Please continue with section D “Mount the
Lifter in permanent position” below. If you do not hear a dial tone continue with section C.
If you do not hear a dial tone, the Lifter may not be raising the handset high enough
or the Conguration Dial may need adjusting.
C. If you do not hear a dial tone
Press Call
Control Button
2. If you still cannot hear a dial tone, you will
need to change the setting on the
Conguration Dial. Using a coin or
paperclip, turn the Conguration Dial
to a dierent setting until you hear a dial tone.
If you still cannot hear a dial tone, please call
Technical Support at 800-544-4660 Extension 5538.
Multiple settings might work with your phone; however, only one is the
optimal position.
1. Check the Lifter height adjustment by moving the Lifter Height Switch to a higher position.
See Section B and repeat steps 4 through 6.
If you hear a dial tone, the lifter height is now set correctly. Please continue with
the next section “Mount the Lifter in Permanent Position”. Position
Indicator
Conguration
Dial

10 Plantronics Voyager 510SSetup Guide
Note: If the side of the phone is curved, the protective cover on the side can be left on
to improve fit.
1. Remove the protective strips from the three mounting tapes on the underside
of the Lifter.
2. gently place the Lifter on the desk phone in the optimum position as determined
above. Test the Lifter to verify positioning by pressing the Call Control Button on your
headset to activate the Lifter and listen for a dial tone.
3. Press firmly to adhere the Lifter to the desk phone.
D. Mount the Lifter in permanent position
Peel back
mounting tape
protective strips
(3 places)
If your handset falls o the phone base or does not re-
turn to its cradle when lowered, you will need to attach
the Extender Arm to the Lifter as described in the HL10
Additional Parts Kit.
Use the Extender Arm to Stabilize Handset
(if needed)