Plantronics Voyager Edge Series User manual

Voyager Edge Series
User Guide

Contents
What's in the box 3
Headset overview 4
Charge case overview 5
Pair 6
Bluetooth pairing 6
NFC pairing 6
Pair Another Phone 6
Select language 7
Charge 8
Use the charge case 9
Fit 10
Adjust the fit 10
The Basics 11
Make/Take/End Calls 11
Mute 12
Adjust the volume 12
Use Smart Sensors 12
Play or pause streaming audio 13
More Features 14
Voice alerts 14
Voice commands 14
Use two phones 15
Change headset settings 15
Update headset firmware 15
2

Headset with medium eartip
Car charger* Combo cable charger*
Earloop Small and large eartip
NOTE *Chargerstylemayvarybyproduct.
What's in the box
3

Call button
Volume button
Charge port
Mute button
Voice button
Play/Pause button
Power button
Headset LED (indicator light)
Headset overview
4

IMPORTANT Fullychargethechargecasepriortouse.
Charge case LEDs; indicates case/headset battery status
Headset: Swipe charge case for headset battery status
Charge case: Swipe charge case for headset battery status
Micro USB charge port
Charge case overview
5

NOTE IfyourphonesupportsNearFieldCommunication(NFC),gotoNFC pairing.
1Wearing your headset, power it on. You hear “welcome” in all the supported languages and then
"pairing" in the default language. The headset LED flashes red and blue.
2Activate Bluetooth®on your phone and set it to search for new devices.
•iPhone Settings > Bluetooth > On*
•Android™> Bluetooth: On > Scan for devices*
NOTE *Menusmayvarybydevice.
3Select “PLT_Edge.” If necessary, enter four zeros (0000) for the passcode or accept the
connection. Once successfully paired, you hear “pairing successful."
1Ensure NFC is on and your phone’s display is unlocked.
2Tap and hold the headset to the phone’s NFC tag location until NFC pairing completes. If
necessary, accept the connection.
NOTE Theheadset’sNFCtagislocatedonthetopoftheheadset.PhoneNFCtaglocationsvary.
After pairing your headset to your phone, you may want to pair another phone.
1Power on your headset.
2Choose:
• Tap the Voice button and say “Pair mode”
•Press and hold the Call button until you hear "pairing"
3Activate Bluetooth on your phone and set it to search for new devices.
4Select “PLT_Edge.”
If necessary, enter four zeros (0000) for the passcode or accept the connection.
Once successfully paired, you hear “pairing successful” and the headset indicator lights stop
flashing.
Pair
Bluetooth pairing
NFC pairing
Pair Another Phone
6

Once your headset is paired and connected to your phone, you can change the headset
language.
1Wearing your headset, power it on.
2Press and hold the Volume up + and down – buttons together until you hear “welcome." The
language selection directions repeat in every supported language.
3Follow the voice-guided prompts to select the headset language.
Select language
7

It takes 90 minutes to fully charge the headset. The indicator light turns off once charging is
complete.
TIP Toresettheaccuracyofthetalktimeprompt,depletetheheadsetbatterythenchargefully.
TIP Tochecktheheadsetbatterystatus,taptheCallbutton whilewearingyourheadsetortapthe
Voicebutton andsay“checkbattery.”
Headset LED behavior while charging with micro USB cable
Off Charging complete
Battery high
Battery medium
Battery low
Battery critical
Charge
8

A fully charged case can supply an additional 11 hours of headset talk time.
IMPORTANT Fullychargethechargecasepriortouse.
Check the charge case or headset battery status by swiping either the case or headset icons.
The LEDs indicate the battery status.
Battery status LEDs for charge case and headset
Battery high
Battery medium
Battery low
Battery critical; Recharge case/headset
Use the charge case
9

The loop of the gel eartip tucks into the back curve of your ear for a stable fit.
1With the headset powered off, replace the eartip with one of the two alternate sizes if it feels
loose or tight in you ear.
2To adjust the fit, rotate the eartip on the headset or add the optional clip-on earloop.
Fit
Adjust the fit
10