Playcraft 1102 User manual

IMPORTANT NOTES: Read First
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
TRI DECK ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev F
7/15/2019
1102
Page 1 of 2
See Installation Manual
Section 09 Collars
Figure 1.1
Figure 1.1
45"
1143mm
42"
1067mm
(A) Use liquid thread lock (such as Loctite
®) with all threaded hardware.
Important: Liquid thread lock (prior
to curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving
as a lubricant during assembly.
(B) The top of the collars are located 7/8" [22mm] below the top of the deck. Refer to Installation Manual for
09 Collars installation instructions.
(C) An appropriate energy absorbing safety surface is required under and around all playground equipment.
Loose fill protective surfacing is shown only as an example for the purpose of this assembly instruction. Other
surfacing material may vary in thickness and/or compression depths. See free publication - The Handbook for
Public Playground Safety, Publication #325 at www.cpsc.gov for the surfacing appropriate for the fall height
of the equipment or consult your surfacing supply representative.
(D) All deck heights on your system's top view drawing are measured from the top of ground cover (finished
grade) to the top of the deck. Post location dimensions are on centers.
(E) Never allow the gap between decks to be between 3-1/2" [89mm] and 9" [229mm]. Deck fillers are
provided for gaps between decks with 6" [152mm] and 12" [305mm] rise increments.
FIGURE 1
Tri Deck Assembly
R5 ASSEMBLY
R3.5 ASSEMBLY

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
1102
Page 2 of 2
Rev F
7/15/2019
TRI DECK ASSEMBLY
INSTALLATION INSTRUCTIONS
3/8" x 2-1/2"
Button Head
Bolt
3/8" x 1" O.D.
Washer
1/2" SAE
Washer
3/8" x 2" Barrel
Nut
1/4" x 1-3/8"
TR Socket
Head Screw
MOUNTING
BLOCK TOP
MOUNTING
BLOCK
BOTTOM
Figure 1.1
Step 1
Attach Deck to Collars as shown in Figure 1.1.
(See Note A)
NOTE: 3 Places
Step 2
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 3
Place required protective surfacing under and
around Tri Deck Assembly. (See Note C)
TRI DECK:
Shall be fabricated from punched, formed, and
welded 12 gauge sheet steel. The Tri Deck shall be
Play Tuff™ coated after fabrication.
MOUNTING BLOCKS:
Shall be two-part and precision die-cast from a high
strength aluminum alloy. The Mounting Blocks shall
have a multi-stage baked-on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
R3.5 Parts List
Part #
DESCRIPTION QTY
CF-7009 Tri Deck R5
1
GF-7006-B Mounting Block R5 Bottom
3
GF-7006-T Mounting Block R5 Top
3
9103112-TR Bolt Button Head 3/8" x 2-1/2"
3
9281062-5-TR Screw Soc HD CS 1/4" x 1-3/8" TR
3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick
3
9345002 Washer Flat SAE 1/2"
3
9443092-TR Nut Barrel 3/8" x 2" BH
3
Part #
DESCRIPTION QTY
CG-8115 Tri Deck R3.5
1
GG-8110 Mounting Block 4 Top R3.5
3
GG-8111 Mounting Block 4 Bottom R3.5
3
9103112-TR Bolt Button Head 3/8" x 2-1/2"
3
9281062-5-TR Screw Soc HD CS 1/4" x 1-3/8" TR
3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick
3
9345002 Washer Flat SAE 1/2"
3
9443092-TR Nut Barrel 3/8" x 2" BH
3
R5 Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance