Playcraft R3.5-1301 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
R3.5 WALL ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev E
10/13/2014
R3.5-1301
Page 1 of 4
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Refer to Installation Manual for R3.5-09 Collars and R3.5-11 Socket Clamps installation instructions.
(C) All gaps created (e.g. between panels, between panel and deck, between panel and roof, etc.) must be less
than 3-1/2" [89mm] or greater than 9" [229mm].
(D) Collar heights will vary with different walls. Use wall to locate collar height.
(E) These instructions apply to all configurations of R3.5 Walls, Short Walls, Tall Walls and Upper Barrier Walls.
Upper Barrier Wall
Deck Mount
R3.5-09 Collars and R3.5-11 Clamps
See Installation Manual Sections
Post Mount
FIGURE 1
R3.5 Wall Assembly
Figure 1.3
Figures 1.1 & 1.2

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
R3.5 WALL ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev E
10/13/2014
R3.5-1301
Page 2 of 4
Step 2
For Deck Mount Walls Only
Attach Panel Brackets to R3.5 Wall as shown
in Figure 1.1. (See Note A)
Step 1
Referring to Elevation View use wall to locate and attach
collars to posts. (See Notes B & C)
*Height shown from top of deck to top of collar.
Elevation View
(Finish Grade)
39" *
Typical
991mm
(See Note C)
R3.5 WALL
PANEL
BRACKET
3/8" x 1" O.D.
Washer
3/8" x 1" Button
Head Bolt
Figure 1.1
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
R3.5 WALL ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev E
10/13/2014
R3.5-1301
Page 3 of 4
Step 3
For Deck Mount Walls Only
Attach Panel Bracket to deck as shown in Figure 1.2.
(See Note A)
Step 4
Attach wall to collars as shown in Figure 1.3.
(See Notes A & B)
Step 5
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Figure 1.3
MOUNTING
LUG
1/2" SAE
Washer
3/8" x 1-3/8"
Shoulder Bolt
R3.5 WALL
Figure 1.2
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
DECK

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
R3.5 WALL ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev E
10/13/2014
R3.5-1301
Page 4 of 4
DECK MOUNT WALL
Part # DESCRIPTION QTY.
BE-0361-L R35 Panel Bracket - Left 1
BE-0361-R R35 Panel Bracket - Right 1
GG-8113 Mounting Lug R3.5 2
HS-1001-R35 Socket Clamp Set R3.5 2
Varies R3.5 Wall 1
9103052-TR Bolt Button Head 3/8" x 1" 4
9103062-TR Bolt Button Head 3/8" x 1-1/4" 2
9143062-TR Bolt Shoulder 3/8" x 1-3/8" BH 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 8
9345002 Washer Flat SAE 1/2" 6
9413002 Nut Lock 3/8" 2
9443022-TR Nut Barrel 3/8" x 5/8" BH 4
POST MOUNT WALL
Part # DESCRIPTION QTY.
GG-8113 Mounting Lug R3.5 4
HS-1001-R35 Socket Clamp Set R3.5 4
Varies R3.5 Wall 1
9143062-TR Bolt Shoulder 3/8" x 1-3/8" BH 4
9345002 Washer Flat SAE 1/2" 4
TALL DECK MOUNT WALL
Part # DESCRIPTION QTY
BE-0361-L R35 Panel Bracket - Left 1
BE-0361-R R35 Panel Bracket - Right 1
GG-8113 Mounting Lug R3.5 4
HS-1001-R35 Socket Clamp Set R3.5 4
Varies R3.5 Wall 1
9103052-TR Bolt Button Head 3/8" x 1" 4
9103062-TR Bolt Button Head 3/8" x 1-1/4" 2
9143062-TR Bolt Shoulder 3/8" x 1-3/8" BH 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 8
9345002 Washer Flat SAE 1/2" 8
9413002 Nut Lock 3/8" 2
9443022-TR Nut Barrel 3/8" x 5/8" BH 4
TALL POST MOUNT WALL
Part # DESCRIPTION QTY
HS-1001-R35 Socket Clamp Set R3.5 6
GG-8113 Mounting Lug R3.5 6
Varies R3.5 Wall 1
9143062-TR Bolt Shoulder 3/8" x 1-3/8" BH 6
9345002 Washer Flat SAE 1/2" 6
R3.5 WALL:
Shall be made from high-density, 3/4" thick,
hot extruded polyethylene sheet plastic specially
formulated for optimum UV stability and color
retention.
R3.5 PANEL BRACKET:
Shall be precision cut from 3/16" HR sheet steel.
The R3.5 Panel Bracket shall have a multi-stage
baked-on powder coat finish.
SOCKET CLAMPS:
Shall be two-part and precision die-cast from a
high strength aluminum alloy. The Socket Clamps
have a multi-stage baked-on powder coat finish.
MOUNTING LUG:
Shall be precision die-cast from a high strength
aluminum alloy. The Mounting Lug shall have a
multi-stage baked-on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance