PlayMechanix amc The Walking Dead Manual instruction

The Walking Dead © 2016 AMC Film Holdings LLC. All Rights Reserved.
The Walking Dead©Game Software Copyright 2016 Play Mechanix™ Inc.
This software is based in part on the work of the Independent JPEG Group.
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)
This product includes cryptographic software written by Eric Young ([email protected])
Setup and Operation
Service Manual
Revision TWD-1.1-7.11-1

Table of Contents
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 2
Safety ............................................................................................................................................................ 3
Product Specifications................................................................................................................................... 5
Setup ............................................................................................................................................................. 6
Game Software Setup ................................................................................................................................. 22
Maintenance ...............................................................................................................................................23
Troubleshooting.......................................................................................................................................... 25
Parts ............................................................................................................................................................ 27
Electrical Wiring ..........................................................................................................................................46
Contact Information....................................................................................................................................49

Page 3 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
OPERATION
Before operating game, read this manual. Failure to properly install and operate this game could result in
malfunction or accident. Operate the game in accordance with the manual.
TRANSPORTING
Cabinet is very heavy and contains fragile components. Use appropriate care when moving or transporting cabinet.
Avoid rough handling.
HANDLING COMPONENTS
Many components are extremely sensitive to handling, environmental and Electrostatic Discharge (ESD) events—
especially the computer. Do not handle it roughly. Before servicing, call your distributor and inquire about the PC
warranty. Use proper ESD procedures when servicing. Protect components from harmful environmental
conditions, such as extreme temperatures, excessive moisture or other damaging effects.
DISCONNECT POWER
Always turn off power and unplug the unit before servicing or making adjustments, unless otherwise instructed.
Installing or repairing components while power is on can damage the components and void the warranty.
GROUNDING
Avoid electrical shock. Do not plug in AC power until you have inspected and properly grounded the unit. Only plug
into a grounded, three-wire outlet. Do not use a “cheater” plug or cut off the ground pin on the line cord.
ELECTRICAL SHOCKS
There is no isolation transformer in the cabinet. Disconnect AC power before servicing. However, be aware that
lethal voltages can remain in the electronic components even when AC power is disconnected. Use extreme
caution when servicing. Verify that there is a working ground connection. If the unit sustains water damage, cease
using it immediately and unplug AC power.
MONITOR
Extremely high voltages exist in the monitor at all times. These high voltages exist even when the monitor is off
and the AC line cord is disconnected. These voltages are extremely lethal and will cause death. The monitor
contains no user serviceable parts. Do not attempt to service the monitor.
POWER SELECTOR
Before installing game, ensure the voltage on the PC is set properly. There is a 115/230 VAC selector switch that
must be set for the correct voltage for your site. Verify the fluorescent lamp rating. The rating must match the line
voltage at the installation site.
CONNECTORS
Ensure all connectors mate properly. If connectors do not slip in easily, do not force them. Connectors are often
keyed and only connect one way. Check for correct orientation.

Safety
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 4
COMPUTER
The computer contains sensitive components, including a hard drive. Do not handle it roughly. Call your distributor
before servicing its internal components. Ask about warranty information as it relates to the PC.
Do not turn the PC power switch on or off. It should remain permanently in the ON position.
Cycle AC power on or off with the cabinet power switch.
A dongle has been inserted into one of the USB ports. This is required for game play.
Do not remove the dongle except for troubleshooting purposes.
POWER CORD
If the power cord is damaged or lost, replace it with an identical cord as supplied by the manufacturer or an
authorized service agent.
WATER JETS
Do not install or operate game within operating perimeter of a water jet. Do not clean equipment using water jet.
HAZARD TO EPILEPTICS
A small portion of the population has an epileptic condition that may cause seizures. Affected persons experience
seizure while watching some television pictures or playing certain video games. People who have not had seizures
may still have an undetected epileptic condition. If anyone in your family has experienced epilepsy symptoms
(seizures or loss of awareness), consult your physical before using video games. While children play video games, a
parent should observe. Be alert to the following symptoms: dizziness, altered vision, eye or muscle twitching,
involuntary movements, loss of awareness, disorientation or convulsions. If you or your child experiences these
symptoms, discontinue use immediately and consult your physician.
MANUAL
Keep this manual available and ready for use. If the game fails to function properly, turn off the machine and
unplug the AC line cord. Contact your local distributor. Your warrantee, when applicable, lasts 60 days from your
purchase date. You may not reproduce this document or any of its contents without written authorization from
Raw Thrills™, Inc. or PlayMechanix™ Inc.
SPECIFICATIONS
For reasons such as performance, this product’s specifications may change without notice. Federal patent,
copyright and other intellectual property laws protect the content, devices and design of the game and its
equipment.

Page 5 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
Electrical Power
Domestic 120 VAC @ 60 Hz, 5 amps
International 240 VAC @ 50 Hz, 2.5 amps
Japan 100 VAC @ 50 Hz, 5 amps
ELECTICAL SAFETY NOTICE
REPLACE FUSE WITH SPECIFIED FUSE RATING ONLY.
DO NOT REPLACE FUSE WITH HIGHER THAN SPECIFIED RATING.
RIO PCB Fuse Guide
+5 VDC ‐ 3 amp Slow Blow (RIO MCU, START BUTTON)
+12 VDC ‐ 5 amp Slow Blow (COIN DOOR, COOLING FANS, DASH LED)
*+12 VDC ‐ AUDIO POWER USES A THERMAL FUSE, RIO F3
Cabinet Fuse Guide
(NOTE: FUSES ARE MOUNTED TO THE LEFT OF THE RIO PCB. F1 IS LOCATED CLOSEST RIO PCB)
F1 - P2 DASH LED, FANS , 5 amp Slow Blow
F2 ‐ P1 DASH LED, MARQUEE, 5 amp Slow Blow
F3 ‐ P2 BOW LED, MARQUEE, 5 amp Slow Blow
F4 ‐ P1 BOW LED, MARQUEE, 5 amp Slow Blow
F5 ‐ MARQUEE, MARQUEE, 5 amp Slow Blow
F6 ‐ BENCH RGB LED T-MOLD, REAR CAB LIGHTING, 5 amp Slow Blow
Temperature
32° to 100° Fahrenheit (0° to 38° Celsius)
Humidity
Must not exceed 95% relative humidity
Cabinet Dimensions
Component
Height
Width
Depth
Assembled Cabinet
100” (254cm)
53.5” (136cm)
85” (216cm)
Seat Assembly
80” (203cm)
53.5” (136cm)
33” (84cm)
Monitor Assembly
76” (193cm)
53.5” (136cm)
34” (86cm)

Setup
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 6
Unpack Carton
1. Place the shipping crate on a flat stable surface.
2. Cut the banding straps and remove the cardboard lid.
3. Lift off the large cardboard container surrounding the cabinet and any shipping cleats.
4. With at least two people and a dolly, remove the cabinet from the shipping pallet.
5. Remove the coin door key from the coin return chute.
6. Open the top coin door.
7. Locate the key for the bottom access panel and the cash box.
Setup Cabinet Components
1. Using a wheeled cart and at least one assistant, transport the cabinet to a suitable playing area.
2. Ensure the main cabinet is level and stable. With at least one assistant, adjust the leg levelers.
3. Check the AC line cord for visible signs of damage.
Pay particular attention to the plug and line cord insulation.
4. Check for shipping damage to the following:
Cabinet Marquee, Cabinet back door, Cabinet coin door, Cabinet decals, Monitor
Install Floor Assembly
1. Locate the mounting brackets and parts bag inside the floor assembly.

Page 7 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
2. Attach brackets to Monitor Assembly with three ¼ -20 x 2” T-27 Torx screws.
(do not fully tighten screws)
3. Connect cables from Monitor Assembly to Floor Assembly.
Be careful not to pinch the cables when sliding Floor Assembly into Monitor Assembly .
4. Attach Floor Assembly to Monitor Assembly with three ¼ -20 x 2” T-27 Torx screws.
(do not fully tighten screws)

Setup
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 8
5. Attach brackets to Floor Assembly with three ¼ -20 x 2” T-27 Torx screws.
(do not fully tighten screws)
6. Connect cables from Seat Assembly to Floor Assembly
Be careful not to pinch the cables when sliding Floor Assembly into Seat Assembly .

Page 9 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
7. Attach Floor Assembly to Seat Assembly with three ¼ -20 x 2” T-27 Torx screws.
(do not fully tighten screws)
8. Fully tighten all ¼ -20 x 2” T-27 Torx screws; there are 12 screws per side.

Setup
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 10
9. Secure floor assembly with four ¼ -20 x 2” T-27 Torx screws with washers.

Page 11 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
Install Cabinet Roof Assembly
1. Locate Cabinet Roof Assembly and six roof assembly bolts with washers.
2. Lift and position Cabinet Roof Assembly on top of Main Cabinet Assembly
Be sure cable connection is directed toward the Monitor Assembly

Setup
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 12
3. Connect cable from Monitor Assembly to Roof Assembly
4. Secure Roof Assembly to Seat Assembly and Monitor Assembly with six ¼ -20 x 2” T-27 security
Torx screws and washers.

Page 13 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
Assemble Marquee Topper
1. Locate marquee and monitor assembly mounting bracket parts.
2. Assemble monitor assembly mounting bracket, using four ¼-20 x .5” Phillips head screws.

Setup
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 14
3. Secure monitor assembly mounting bracket to marquee, using four ¼-20 x .5” Phillips head
screws. Two of these screws are located on the interior of the mounting bracket.
Be careful not to pinch the power cable.
4. Secure seat assembly mounting bracket to marquee using 4 ¼-20 x .5” Phillips head screws.

Page 15 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
Install Marquee Topper
1. Locate Main Marquee Assembly, Rear Marquee Assembly, and associated parts bag.
2. With an assistant, position the Main Marquee Assembly on top of the cabinet.
3. Connect and route the power cable from the Monitor Assembly to the Main Marquee Assembly.
Be careful not to pinch the cable between the topper and cabinet.

Setup
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 16
4. Attach Main Marquee Assembly to Monitor Assembly using six ¼-20 x 1.5” hexhead screws.
(do not fully tighten screws)
5. Attach Main Marquee Assembly to Seat Assembly using two ¼-20 x 1.5” hexhead screws.
(do not fully tighten screws)

Page 17 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
6. Connect and route the power cable from the Seat Assembly to the Rear Marquee Assembly.
Be careful not to pinch the cable between the topper and cabinet.
7. Hook Rear Marquee Assembly to Main Marquee Assembly

Setup
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 18
8. Secure Rear Marquee Assembly to Main Marquee Assembly using four screws.
9. Fully tighten all Marquee Topper screws.

Page 19 Walking Dead© Game Software copyright 2016 PlayMechanix™ Inc. All rights reserved.
Install Razor Wire
1. Locate the left and right Rear Razor Wire assemblies.
2. Connect cables from Rear Razor assemblies to the Seat Assembly.
Be careful not to pinch the cables between the assembly and the cabinet.

Setup
Copyright © 2016 Play Mechanix™ Inc. All rights reserved. Page 20
3. Secure each Razor Wire Assembly to Seat Assembly and Rear Marquee Assembly with six screws
and washers. Be sure to fully tighten all screws.