pleasant hearth OFW327RC User manual

1
Serial Number Purchase Date
ATTACH YOUR RECEIPT HERE
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-447-4768, 8:30 a.m. – 4:30 p.m. CST, Monday – Friday, or
email us at [email protected].
03/20/18
BRENTWOOD FIRE PIT
MODEL #OFW327RC / #OFW327R-1
30-10-101
Français p. 17
Español p. 9

2
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
AMesh Cover 1
BWood Grate 1
CFire Bowl 1
D Upper Support Ring 1
ELegs 4
F Lower Support Ring 1
GPoker 1
HCooking Grid 1
IAsh Catcher 1
E
F
C
B
A
H
D
G
I
** NOTE: Cooking grid part ONLY applies to model # OFW327RC

3
HARDWARE LIST
Please read and understand this entire manual before attempting to assemble, operate or install
the product. If you have any questions regarding the product, please call customer service at
1-877-447-4768, 8:30 a.m. – 4:30 p.m. CST, Monday – Friday.
WARNINGS:
• DO NOT allow children or pets near the re pit without supervision.
• DO NOT touch surface of re pit while in use.
• FOR OUTDOOR USE ONLY! Burning wood and charcoal indoors can kill you. It gives off carbon
monoxide, which has no odor.
• NEVER burn in vehicles, tents, garages, other enclosed areas or indoors. CARBON MONOXIDE
HAZARD.
• NEVER LEAVE FIRE UNATTENDED!
• NEVER place a cover on re pit when in use. Ensure the re pit and mesh cover have cooled before
placing a cover over the re pit.
• When the re pit is in use, the poker bracket on the mesh cover can reach extreme temperatures
that can cause serious injury to an unprotected hand. Use a poker when handling.
• DO NOT use under overhead cables or power lines.
CAUTIONS:
• Adequate re extinguishing material should be readily available.
• Always ensure that the mesh cover is secured over re bowl while in use.
• Burn only seasoned hard wood or re logs in the re pit.
• DO NOT attempt to move the re pit while it is hot or in use.
• DO NOT use gasoline or kerosene to start the re in your re pit.
• DO NOT use this outdoor re pit under any overhead or near any unprotected combustible
constructions. Avoid using near or under overhanging trees and shrubs. DO NOT use this unit on
long or dry grass and/or leaves.
• Always use this outdoor re pit on a hard, level, non-combustible surface such as concrete, rock or
stone. An asphalt or blacktop surface may not be acceptable for this purpose. DO NOT use on
wooden decks.
• Place the re pit no closer than 10 feet / 3.05 meters from walls or combustibles during use.
• Poker handle may become hot during and after use.
• Use heat-resistant gloves to handle hot tools.
SAFETY INFORMATION
M6x20mm
Bolt
Qty. 8
M6x12mm
Bolt
Qty. 7
AA BB CC DD
M6 Nut
Qty. 11
M6 Wrench
Qty. 1
This product and the fuels used to operate this product (charcoal or wood), and the products of
combustion of such fuels, can expose you to chemicals including carbon black, which is known
to the State of California to cause cancer, and carbon monoxide, which is known to the State of
California to cause birth defects or other reproductive harm.
For more information go to www.p65Warnings.ca.gov
WARNING

4
PREPARATION
ASSEMBLY INSTRUCTIONS
1. Attach legs (E) to the lower support ring (F) by
inserting M6x12mm bolts (BB) through pre-drilled
holes in lower support ring (F) and legs (E) and
secure.
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents above. If any part is missing or damaged, do not attempt to
assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 25 minutes
Tools Required for Assembly: Wrench (Included)
Hardware Used
1
E
F
BB M6x12mm Bolt x 4
BB

5
2. Attach legs (E) to the upper support ring (D)
by inserting M6x20mm bolts (AA) through pre-
drilled holes in legs (E) and upper support ring
(D) and secure with M6 nuts (CC) as illustrated.
Tighten all bolts with wrench (DD).
ASSEMBLY INSTRUCTIONS
2
AA
3
D
E
CC
EE
Hardware Used
CC M6 Nut x 8
DD M6 Wrench
AA M6x20mm Bolt x8
x3
x3
3. Attach ash catcher (I) to the re bowl (C) us-
ing M6x12mm bolts (BB) and M6 nut (CC) as
illustrated.
4. Place re bowl (C) into re bowl holder.
EE
Hardware Used
CC M6 Nut
BB M6x12mm Bolt
4
C
BB
C
CC
I