PNI IP20MP User manual

Fast Manual Instructions
Outdoor varifocal IP camera
PNI IP20MP
This operation manual is only for a brief
description of the product, for more
product information please open the
CDROM.
Choose IP address to config. IP address
and port are displayed on the right, you
can modify the IP parameters and click
"Modify" to save.
Note: IP address of the speed dome
must share the same network segment
with the router and conform to the
router's IP, and make sure the IP is not
conflicted in the network of LAN. Go
to[conform to local PC] to automatically
match subnet mask and default
gateway with local computer.
Note: Plug-ins need to be installed if you
login via IE browser. IE is default to
intercept plug-in.
Please set IE security level. Go to
<internet options>--<security>--<
Customized level> and Enable all
ActiveX options. Install Active X plig-in
fromt he CD included in the package.
4.2 CMS access
1. Open the CD search and install the
General CMS software.CMS shortcut
icon will be displayed when installed
successfully.
2.Double-click CMS shortcut icon, input
user name and password( user name:
super, no password) to login.
4.3 Mobile Access
Network environment: WIFI, 3G
Mobile system: Android, iOS
Software Name: VmEyeCloud
Open vMEye application and add your
camera using the option “By Device”.
Click “Add” on top left of “Device List”, to
access “Device Detail”. You can add
manually or click “Search” to add the
devices on LAN.
Note: The detailed user manual of the
mobile applications can be found on the
CD included in the package.
3.Go to [Main Menu] > [System] >
[Device Manager] to add camera to
CMS .
Note: The CMS detailed user manual
can be found on the CD included in the
package.
3.1 Boot up
Please use the formal 12 V 2A power
adapter.
Please use the positive power of about
50 seconds of network cameras start
complete, the network camera through
a cable connected to the LAN. We
recommend the accesories from the
page 8.
3.2 IP config
[IP address]:default is 192.168.1.10
[Subnet Mask]:default is 255.255.255.0
[Gateway]:default is 192.168.1.1.
Open the CD and install the software
General Device Manager.
Then click [IP search], all online IP
addresses of the monitoring devices
within the LAN will be searched and
displayed.
4.1 IE Access
Open web browser, enter IP address,
take 192.168.1.1 O as an example,
input http: //192.168.1.10 to connect.
Enter user name and password
(default user name is admin, no
password). Change the administrator
password after login.
After successful login, go to [Stream
menu] to connect main stream or
substream.
1. Introduction:
2. Product description:
3. Boot up & IP configuration: 4. Camera Access:
1
1
2
3
4
Choose one IP address
Main menu
Stream selection
PTZ control
Shortcut menu
1. 3. 5. 7.
2. 4. 6.
Waterproof
metalic case
36 IR LED
Network interface
DC 12V input
5. Technical specifications:
ŸSensor: CMOS
ŸIR-CUT filter
ŸResolution1080P / 2.0 MP
ŸVideo system PAL
ŸFixed 3.6mm Lens
Ÿ36 pcs. IR LED
Ÿ30 Meter illumination
ŸSupports: iOS, Android
ŸSupports ONVIF 2.4 protocol
ŸPort Ethernet 10 / 100 Mbps
ŸSupports iCloud (P2P) function
ŸSupports Internet Explorer
ŸWaterproof IP66
ŸWorking temperature
-20°C ~ +40°C
ŸWorking humidity <95%

Fast Manual Instructions
Outdoor varifocal IP camera
PNI IP20MP
This operation manual is only for a brief
description of the product, for more
product information please open the
CDROM.
Choose IP address to config. IP address
and port are displayed on the right, you
can modify the IP parameters and click
"Modify" to save.
Note: IP address of the speed dome
must share the same network segment
with the router and conform to the
router's IP, and make sure the IP is not
conflicted in the network of LAN. Go
to[conform to local PC] to automatically
match subnet mask and default
gateway with local computer.
Note: Plug-ins need to be installed if you
login via IE browser. IE is default to
intercept plug-in.
Please set IE security level. Go to
<internet options>--<security>--<
Customized level> and Enable all
ActiveX options. Install Active X plig-in
fromt he CD included in the package.
4.2 CMS access
1. Open the CD search and install the
General CMS software.CMS shortcut
icon will be displayed when installed
successfully.
2.Double-click CMS shortcut icon, input
user name and password( user name:
super, no password) to login.
4.3 Mobile Access
Network environment: WIFI, 3G
Mobile system: Android, iOS
Software Name: VmEyeCloud
Open vMEye application and add your
camera using the option “By Device”.
Click “Add” on top left of “Device List”, to
access “Device Detail”. You can add
manually or click “Search” to add the
devices on LAN.
Note: The detailed user manual of the
mobile applications can be found on the
CD included in the package.
3.Go to [Main Menu] > [System] >
[Device Manager] to add camera to
CMS .
Note: The CMS detailed user manual
can be found on the CD included in the
package.
3.1 Boot up
Please use the formal 12 V 2A power
adapter.
Please use the positive power of about
50 seconds of network cameras start
complete, the network camera through
a cable connected to the LAN. We
recommend the accesories from the
page 8.
3.2 IP config
[IP address]:default is 192.168.1.10
[Subnet Mask]:default is 255.255.255.0
[Gateway]:default is 192.168.1.1.
Open the CD and install the software
General Device Manager.
Then click [IP search], all online IP
addresses of the monitoring devices
within the LAN will be searched and
displayed.
4.1 IE Access
Open web browser, enter IP address,
take 192.168.1.1 O as an example,
input http: //192.168.1.10 to connect.
Enter user name and password
(default user name is admin, no
password). Change the administrator
password after login.
After successful login, go to [Stream
menu] to connect main stream or
substream.
1. Introduction:
2. Product description:
3. Boot up & IP configuration: 4. Camera Access:
1
1
2
3
4
Choose one IP address
Main menu
Stream selection
PTZ control
Shortcut menu
1. 3. 5. 7.
2. 4. 6.
Waterproof
metalic case
36 IR LED
Network interface
DC 12V input
5. Technical specifications:
ŸSensor: CMOS
ŸIR-CUT filter
ŸResolution1080P / 2.0 MP
ŸVideo system PAL
ŸFixed 3.6mm Lens
Ÿ36 pcs. IR LED
Ÿ30 Meter illumination
ŸSupports: iOS, Android
ŸSupports ONVIF 2.4 protocol
ŸPort Ethernet 10 / 100 Mbps
ŸSupports iCloud (P2P) function
ŸSupports Internet Explorer
ŸWaterproof IP66
ŸWorking temperature
-20°C ~ +40°C
ŸWorking humidity <95%

Fast Manual Instructions
Outdoor varifocal IP camera
PNI IP20MP
This operation manual is only for a brief
description of the product, for more
product information please open the
CDROM.
Choose IP address to config. IP address
and port are displayed on the right, you
can modify the IP parameters and click
"Modify" to save.
Note: IP address of the speed dome
must share the same network segment
with the router and conform to the
router's IP, and make sure the IP is not
conflicted in the network of LAN. Go
to[conform to local PC] to automatically
match subnet mask and default
gateway with local computer.
Note: Plug-ins need to be installed if you
login via IE browser. IE is default to
intercept plug-in.
Please set IE security level. Go to
<internet options>--<security>--<
Customized level> and Enable all
ActiveX options. Install Active X plig-in
fromt he CD included in the package.
4.2 CMS access
1. Open the CD search and install the
General CMS software.CMS shortcut
icon will be displayed when installed
successfully.
2.Double-click CMS shortcut icon, input
user name and password( user name:
super, no password) to login.
4.3 Mobile Access
Network environment: WIFI, 3G
Mobile system: Android, iOS
Software Name: VmEyeCloud
Open vMEye application and add your
camera using the option “By Device”.
Click “Add” on top left of “Device List”, to
access “Device Detail”. You can add
manually or click “Search” to add the
devices on LAN.
Note: The detailed user manual of the
mobile applications can be found on the
CD included in the package.
3.Go to [Main Menu] > [System] >
[Device Manager] to add camera to
CMS .
Note: The CMS detailed user manual
can be found on the CD included in the
package.
3.1 Boot up
Please use the formal 12 V 2A power
adapter.
Please use the positive power of about
50 seconds of network cameras start
complete, the network camera through
a cable connected to the LAN. We
recommend the accesories from the
page 8.
3.2 IP config
[IP address]:default is 192.168.1.10
[Subnet Mask]:default is 255.255.255.0
[Gateway]:default is 192.168.1.1.
Open the CD and install the software
General Device Manager.
Then click [IP search], all online IP
addresses of the monitoring devices
within the LAN will be searched and
displayed.
4.1 IE Access
Open web browser, enter IP address,
take 192.168.1.1 O as an example,
input http: //192.168.1.10 to connect.
Enter user name and password
(default user name is admin, no
password). Change the administrator
password after login.
After successful login, go to [Stream
menu] to connect main stream or
substream.
1. Introduction:
2. Product description:
3. Boot up & IP configuration: 4. Camera Access:
1
1
2
3
4
Choose one IP address
Main menu
Stream selection
PTZ control
Shortcut menu
1. 3. 5. 7.
2. 4. 6.
Waterproof
metalic case
36 IR LED
Network interface
DC 12V input
5. Technical specifications:
ŸSensor: CMOS
ŸIR-CUT filter
ŸResolution1080P / 2.0 MP
ŸVideo system PAL
ŸFixed 3.6mm Lens
Ÿ36 pcs. IR LED
Ÿ30 Meter illumination
ŸSupports: iOS, Android
ŸSupports ONVIF 2.4 protocol
ŸPort Ethernet 10 / 100 Mbps
ŸSupports iCloud (P2P) function
ŸSupports Internet Explorer
ŸWaterproof IP66
ŸWorking temperature
-20°C ~ +40°C
ŸWorking humidity <95%

Fast Manual Instructions
Outdoor varifocal IP camera
PNI IP20MP
This operation manual is only for a brief
description of the product, for more
product information please open the
CDROM.
Choose IP address to config. IP address
and port are displayed on the right, you
can modify the IP parameters and click
"Modify" to save.
Note: IP address of the speed dome
must share the same network segment
with the router and conform to the
router's IP, and make sure the IP is not
conflicted in the network of LAN. Go
to[conform to local PC] to automatically
match subnet mask and default
gateway with local computer.
Note: Plug-ins need to be installed if you
login via IE browser. IE is default to
intercept plug-in.
Please set IE security level. Go to
<internet options>--<security>--<
Customized level> and Enable all
ActiveX options. Install Active X plig-in
fromt he CD included in the package.
4.2 CMS access
1. Open the CD search and install the
General CMS software.CMS shortcut
icon will be displayed when installed
successfully.
2.Double-click CMS shortcut icon, input
user name and password( user name:
super, no password) to login.
4.3 Mobile Access
Network environment: WIFI, 3G
Mobile system: Android, iOS
Software Name: VmEyeCloud
Open vMEye application and add your
camera using the option “By Device”.
Click “Add” on top left of “Device List”, to
access “Device Detail”. You can add
manually or click “Search” to add the
devices on LAN.
Note: The detailed user manual of the
mobile applications can be found on the
CD included in the package.
3.Go to [Main Menu] > [System] >
[Device Manager] to add camera to
CMS .
Note: The CMS detailed user manual
can be found on the CD included in the
package.
3.1 Boot up
Please use the formal 12 V 2A power
adapter.
Please use the positive power of about
50 seconds of network cameras start
complete, the network camera through
a cable connected to the LAN. We
recommend the accesories from the
page 8.
3.2 IP config
[IP address]:default is 192.168.1.10
[Subnet Mask]:default is 255.255.255.0
[Gateway]:default is 192.168.1.1.
Open the CD and install the software
General Device Manager.
Then click [IP search], all online IP
addresses of the monitoring devices
within the LAN will be searched and
displayed.
4.1 IE Access
Open web browser, enter IP address,
take 192.168.1.1 O as an example,
input http: //192.168.1.10 to connect.
Enter user name and password
(default user name is admin, no
password). Change the administrator
password after login.
After successful login, go to [Stream
menu] to connect main stream or
substream.
1. Introduction:
2. Product description:
3. Boot up & IP configuration: 4. Camera Access:
1
1
2
3
4
Choose one IP address
Main menu
Stream selection
PTZ control
Shortcut menu
1. 3. 5. 7.
2. 4. 6.
Waterproof
metalic case
36 IR LED
Network interface
DC 12V input
5. Technical specifications:
ŸSensor: CMOS
ŸIR-CUT filter
ŸResolution1080P / 2.0 MP
ŸVideo system PAL
ŸFixed 3.6mm Lens
Ÿ36 pcs. IR LED
Ÿ30 Meter illumination
ŸSupports: iOS, Android
ŸSupports ONVIF 2.4 protocol
ŸPort Ethernet 10 / 100 Mbps
ŸSupports iCloud (P2P) function
ŸSupports Internet Explorer
ŸWaterproof IP66
ŸWorking temperature
-20°C ~ +40°C
ŸWorking humidity <95%

Fast Manual Instructions
Outdoor varifocal IP camera
PNI IP20MP
This operation manual is only for a brief
description of the product, for more
product information please open the
CDROM.
Choose IP address to config. IP address
and port are displayed on the right, you
can modify the IP parameters and click
"Modify" to save.
Note: IP address of the speed dome
must share the same network segment
with the router and conform to the
router's IP, and make sure the IP is not
conflicted in the network of LAN. Go
to[conform to local PC] to automatically
match subnet mask and default
gateway with local computer.
Note: Plug-ins need to be installed if you
login via IE browser. IE is default to
intercept plug-in.
Please set IE security level. Go to
<internet options>--<security>--<
Customized level> and Enable all
ActiveX options. Install Active X plig-in
fromt he CD included in the package.
4.2 CMS access
1. Open the CD search and install the
General CMS software.CMS shortcut
icon will be displayed when installed
successfully.
2.Double-click CMS shortcut icon, input
user name and password( user name:
super, no password) to login.
4.3 Mobile Access
Network environment: WIFI, 3G
Mobile system: Android, iOS
Software Name: VmEyeCloud
Open vMEye application and add your
camera using the option “By Device”.
Click “Add” on top left of “Device List”, to
access “Device Detail”. You can add
manually or click “Search” to add the
devices on LAN.
Note: The detailed user manual of the
mobile applications can be found on the
CD included in the package.
3.Go to [Main Menu] > [System] >
[Device Manager] to add camera to
CMS .
Note: The CMS detailed user manual
can be found on the CD included in the
package.
3.1 Boot up
Please use the formal 12 V 2A power
adapter.
Please use the positive power of about
50 seconds of network cameras start
complete, the network camera through
a cable connected to the LAN. We
recommend the accesories from the
page 8.
3.2 IP config
[IP address]:default is 192.168.1.10
[Subnet Mask]:default is 255.255.255.0
[Gateway]:default is 192.168.1.1.
Open the CD and install the software
General Device Manager.
Then click [IP search], all online IP
addresses of the monitoring devices
within the LAN will be searched and
displayed.
4.1 IE Access
Open web browser, enter IP address,
take 192.168.1.1 O as an example,
input http: //192.168.1.10 to connect.
Enter user name and password
(default user name is admin, no
password). Change the administrator
password after login.
After successful login, go to [Stream
menu] to connect main stream or
substream.
1. Introduction:
2. Product description:
3. Boot up & IP configuration: 4. Camera Access:
1
1
2
3
4
Choose one IP address
Main menu
Stream selection
PTZ control
Shortcut menu
1. 3. 5. 7.
2. 4. 6.
Waterproof
metalic case
36 IR LED
Network interface
DC 12V input
5. Technical specifications:
ŸSensor: CMOS
ŸIR-CUT filter
ŸResolution1080P / 2.0 MP
ŸVideo system PAL
ŸFixed 3.6mm Lens
Ÿ36 pcs. IR LED
Ÿ30 Meter illumination
ŸSupports: iOS, Android
ŸSupports ONVIF 2.4 protocol
ŸPort Ethernet 10 / 100 Mbps
ŸSupports iCloud (P2P) function
ŸSupports Internet Explorer
ŸWaterproof IP66
ŸWorking temperature
-20°C ~ +40°C
ŸWorking humidity <95%

Fast Manual Instructions
Outdoor varifocal IP camera
PNI IP20MP
This operation manual is only for a brief
description of the product, for more
product information please open the
CDROM.
Choose IP address to config. IP address
and port are displayed on the right, you
can modify the IP parameters and click
"Modify" to save.
Note: IP address of the speed dome
must share the same network segment
with the router and conform to the
router's IP, and make sure the IP is not
conflicted in the network of LAN. Go
to[conform to local PC] to automatically
match subnet mask and default
gateway with local computer.
Note: Plug-ins need to be installed if you
login via IE browser. IE is default to
intercept plug-in.
Please set IE security level. Go to
<internet options>--<security>--<
Customized level> and Enable all
ActiveX options. Install Active X plig-in
fromt he CD included in the package.
4.2 CMS access
1. Open the CD search and install the
General CMS software.CMS shortcut
icon will be displayed when installed
successfully.
2.Double-click CMS shortcut icon, input
user name and password( user name:
super, no password) to login.
4.3 Mobile Access
Network environment: WIFI, 3G
Mobile system: Android, iOS
Software Name: VmEyeCloud
Open vMEye application and add your
camera using the option “By Device”.
Click “Add” on top left of “Device List”, to
access “Device Detail”. You can add
manually or click “Search” to add the
devices on LAN.
Note: The detailed user manual of the
mobile applications can be found on the
CD included in the package.
3.Go to [Main Menu] > [System] >
[Device Manager] to add camera to
CMS .
Note: The CMS detailed user manual
can be found on the CD included in the
package.
3.1 Boot up
Please use the formal 12 V 2A power
adapter.
Please use the positive power of about
50 seconds of network cameras start
complete, the network camera through
a cable connected to the LAN. We
recommend the accesories from the
page 8.
3.2 IP config
[IP address]:default is 192.168.1.10
[Subnet Mask]:default is 255.255.255.0
[Gateway]:default is 192.168.1.1.
Open the CD and install the software
General Device Manager.
Then click [IP search], all online IP
addresses of the monitoring devices
within the LAN will be searched and
displayed.
4.1 IE Access
Open web browser, enter IP address,
take 192.168.1.1 O as an example,
input http: //192.168.1.10 to connect.
Enter user name and password
(default user name is admin, no
password). Change the administrator
password after login.
After successful login, go to [Stream
menu] to connect main stream or
substream.
1. Introduction:
2. Product description:
3. Boot up & IP configuration: 4. Camera Access:
1
1
2
3
4
Choose one IP address
Main menu
Stream selection
PTZ control
Shortcut menu
1. 3. 5. 7.
2. 4. 6.
Waterproof
metalic case
36 IR LED
Network interface
DC 12V input
5. Technical specifications:
ŸSensor: CMOS
ŸIR-CUT filter
ŸResolution1080P / 2.0 MP
ŸVideo system PAL
ŸFixed 3.6mm Lens
Ÿ36 pcs. IR LED
Ÿ30 Meter illumination
ŸSupports: iOS, Android
ŸSupports ONVIF 2.4 protocol
ŸPort Ethernet 10 / 100 Mbps
ŸSupports iCloud (P2P) function
ŸSupports Internet Explorer
ŸWaterproof IP66
ŸWorking temperature
-20°C ~ +40°C
ŸWorking humidity <95%

Fast Manual Instructions
Outdoor varifocal IP camera
PNI IP20MP
This operation manual is only for a brief
description of the product, for more
product information please open the
CDROM.
Choose IP address to config. IP address
and port are displayed on the right, you
can modify the IP parameters and click
"Modify" to save.
Note: IP address of the speed dome
must share the same network segment
with the router and conform to the
router's IP, and make sure the IP is not
conflicted in the network of LAN. Go
to[conform to local PC] to automatically
match subnet mask and default
gateway with local computer.
Note: Plug-ins need to be installed if you
login via IE browser. IE is default to
intercept plug-in.
Please set IE security level. Go to
<internet options>--<security>--<
Customized level> and Enable all
ActiveX options. Install Active X plig-in
fromt he CD included in the package.
4.2 CMS access
1. Open the CD search and install the
General CMS software.CMS shortcut
icon will be displayed when installed
successfully.
2.Double-click CMS shortcut icon, input
user name and password( user name:
super, no password) to login.
4.3 Mobile Access
Network environment: WIFI, 3G
Mobile system: Android, iOS
Software Name: VmEyeCloud
Open vMEye application and add your
camera using the option “By Device”.
Click “Add” on top left of “Device List”, to
access “Device Detail”. You can add
manually or click “Search” to add the
devices on LAN.
Note: The detailed user manual of the
mobile applications can be found on the
CD included in the package.
3.Go to [Main Menu] > [System] >
[Device Manager] to add camera to
CMS .
Note: The CMS detailed user manual
can be found on the CD included in the
package.
3.1 Boot up
Please use the formal 12 V 2A power
adapter.
Please use the positive power of about
50 seconds of network cameras start
complete, the network camera through
a cable connected to the LAN. We
recommend the accesories from the
page 8.
3.2 IP config
[IP address]:default is 192.168.1.10
[Subnet Mask]:default is 255.255.255.0
[Gateway]:default is 192.168.1.1.
Open the CD and install the software
General Device Manager.
Then click [IP search], all online IP
addresses of the monitoring devices
within the LAN will be searched and
displayed.
4.1 IE Access
Open web browser, enter IP address,
take 192.168.1.1 O as an example,
input http: //192.168.1.10 to connect.
Enter user name and password
(default user name is admin, no
password). Change the administrator
password after login.
After successful login, go to [Stream
menu] to connect main stream or
substream.
1. Introduction:
2. Product description:
3. Boot up & IP configuration: 4. Camera Access:
1
1
2
3
4
Choose one IP address
Main menu
Stream selection
PTZ control
Shortcut menu
1. 3. 5. 7.
2. 4. 6.
Waterproof
metalic case
36 IR LED
Network interface
DC 12V input
5. Technical specifications:
ŸSensor: CMOS
ŸIR-CUT filter
ŸResolution1080P / 2.0 MP
ŸVideo system PAL
ŸFixed 3.6mm Lens
Ÿ36 pcs. IR LED
Ÿ30 Meter illumination
ŸSupports: iOS, Android
ŸSupports ONVIF 2.4 protocol
ŸPort Ethernet 10 / 100 Mbps
ŸSupports iCloud (P2P) function
ŸSupports Internet Explorer
ŸWaterproof IP66
ŸWorking temperature
-20°C ~ +40°C
ŸWorking humidity <95%