PotteryBarn Cheswick User manual

Cheswick
Dining
Arm
Chair
Assembly Instructions
Pre
-
Assembly:

Please read all instructions before beginning assembly.

For your safety and convenience, assembly by two people is recommended.

Remove all parts from the box and lay out on a clear
carpeted or scratch
-
free work surf
ace. (The shipping box
provides
an ideal work surface), this will avoid damaging any parts during assembly. Do not dispose of any
contents until
assembly is completed to avoid accidentally discarding small parts.

Use the p
arts lists above to identify and separate each of the pieces included.
Parts Included:
Hardware Included:

(1) Back Rest (A)

(
1)
Seat Frame (B)

(2) Front Leg Left
(CL)
and Right (C
R
)

(2) Side Stretcher Left
(DL)
and Right (D
R
)

(2) Arm Rest
Left
(E
L
)
and Right (ER)

(4) Pan Head Screw M4 x 38 (F)

(8) JCBC Bolt M6 x 70 (G)

(4
) JCBC Bolt M6 x 50 (H)

(2
) JCBC Bolt M6 x 35 (I)

(2) Flat Washer M6 x 13 (J)

(12
) Flat Washer M6 x 16 (K)

(14
) Spring Washer M6 x 13 (L)

(
1) Allen Key M4 (M
)

(4) Barrel Nut M6 x
10 x 20 (N)
Assembly Instructions:
(1)
Position the back rest (A) on a soft surface such as a carpet. Place the seat frame (B) on to the middle rail of the
chair back (A). Make sure that the screw holes on the apron frame are facing down. (Fig. 1)
(2)
Insert the JCBC bolts M6 x 35 (I), flat washer
(K)
and spring washer (L) into the pre
-
drilled holes on the seat
frame at rear rail
and tighten the JCBC bolt with Allen key provided. (Fig. 1)
(3)
Attach seat frame (B) and back rest (A). Insert JCBC bolt M6 x 70
(G), flat washer (K), spring washer (L) into ther
four holes in the
corner and tighten with Allen key (M). (Fig. 1)
Fig. 1

(4)
Insert the front leg (C
L & CR
) at the position illustrated
below
. Tighten with JCBC Bolt M6 x 70 (G), flat washer
(K),
spring washer (L)
and Allen key (M) through all four holes in the corner. (Fig. 2)
(5)
Insert
pan head screw (F) into side stretcher (D
L & DR
) through the pre
-
drilled holes, tighten with screw
-
driver.
(Not provided). (Fig. 3)
(6)
Insert barrel nut M6 x 10 x 20 (N)
into the pre
-
drilled hole in the arm rest (E). (Fig. 4)
(7)
Attach arm rest (E
L & ER
) to back rest (A) with JCBC bolt M6 x 50 (H), flat washer
(J),
spring washer (L) and seat
frame (B) with
JCBC bolt M6 x
50 (H
), flat washer
(K
),
spring washer (L) as show in
the illustration. Tighten with
Allen key (M)
.
(Fig. 4)
Care Instructions:

Dust with a clean, soft cloth

Avoid the use of chemicals and harsh cleaning agents
thank
you for your purchase
stores | catalog |
www.potterybarn.com
Fig.
3
Fig. 2
Fig. 4
Fig. 4