PowerPac PPIN617 User manual

Model: PPIN617

LIST OF COMPONENTS
1.
2.
3.
4.
5.
6.
7.
Steam Brush
Water Tank
Stainless Steel Panel
Main Body
Power button / Indicator light
Steam Switch Locking Slider
Steam Switch
PARTS & DESCRIPTION
Main BodyStainless Steel PanelSteam Brush
Power Button /
Indicator Light
Steam Lock Slider
Steam Switch
Water Tank
1

ATTENTION :
Read this booklet carefully as it contains important instructions for a safe installation,
use and maintenance.
Important instructions to be kept for future reference.
The following basic precautions should always be followed when using electrical
appliances:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Read all instructions before using the appliance.
This appliance must be used only for the purpose it was expressly designed; any
use NOT complying with the instructions contained in the manual is considered
inappropriate and dangerous. The manufacturer is NOT responsible for possible
damages caused by the inappropriate and/or unreasonable use.
The Water Tank in the garment steamer (henceforth called the “steamer”) is
designed for heating water only. DO NOT put other liquids into it. Different liquids
have different boiling points, with volatile liquids having boiling points lower than
100°C, the boiling point of water.
This appliance is NOT suitable to be used or stored near heat sources (open flame,
ovens, heaters, stoves, etc.) and/or in an explosive environment (in the presence of
flammable substances such as gas, vapour, mist or dust, in atmospheric conditions
when, after ignition, the combustion is spread in the air). Items containing these
substances should never be placed in the appliance, and never be used to clean the
appliance in order to avert the risk of fire or explosion.
The packing materials (plastic bags, expanded polystyrene, etc.) must be kept out
of the reach of children or disabled persons since they represent potential sources
of danger.
The installation/assembly of the appliance will be made in accordance with the
indications of the manufacturer. A wrong procedure may cause damages to persons,
animals or objects, for which the manufacturer cannot be considered responsible.
Before use, check the integrity of the appliance and power cable. In case you are not
sure, contact a qualified person. If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a qualified technician in order to avoid a
shock hazard.
Before powering the appliance make sure the rating (voltage and frequency)
corresponding to the grid and the socket is suitable for the plug of the appliance,
and that the wall socket is properly grounded.
DO NOT power the appliance using multiple sockets. If possible, avoid the use of
adapters and/or extension cables; if their use is absolutely necessary, use only
materials in compliance with the current safety regulations and according to the
electrical parameters of the adapters.
The appliance must NOT be switched on using external timers and/or other remote
control appliances which are not specified in this manual.
Only use original components & accessories provided by the manufacturer. Any
non-original components & accessories NOT recommended by the manufacturer)
may cause injuries to persons or damage to the appliance.
WARNINGS
2

Clean the exterior of the steamer with water & detergent with a non-abrasive
sponge.
DO NOT use metal scouring pads.
Place and use the appliance on a flat, horizontal, stable and heat-resistant surface.
Fill the Water Tank with water before steaming. Be aware of the water level as it
depletes while in operation. If you require to top-up water, switch off the
appliance and unplug from the electric mains first. DO NOT top-up water while
the appliance in ON. Thereafter, ensure that the exterior of the steamer is
completely dry before use.
Keep the nozzle and the Stainless Steel Panel upright and steam only in a vertical
motion, never in a horizontal motion or tilted backwards as doing so may lead to
hot water discharge.
After using the appliance, switch off the appliance and unplug from the electric
mains. Wait for 60 minutes to allow sufficient time for the appliance to cool before
cleaning the product, installing or disassembling accessories, emptying the Water
Tank (this should be done after every use) or storing it.
cover the appliance during functioning;
obstruct totally nor partially the nozzle and the Stainless Steel Panel;
insert objects or body parts inside the protection cover of the appliance, the
nozzle, the Stainless Steel Panel or the Body;
add water in excess of the “MAX” mark indicated;
switch the appliance on if the Water Tank is dry - however, should the Water Tank
be found empty during operation, immediately unplug the power cable and add
water to avoid dry-boil;
leave the appliance unsupervised during operation.
12.
13.
14.
15.
16.
If you are using the appliance for the first time, you should:
a.
b.
c.
d.
Make sure to remove any label or protective sheet which may prevent its proper
functioning.
DO NOT:
•
•
•
•
•
•
Plug and unplug the power cable with dry hands and hold it firmly. Always unplug
the power cable to avoid overheating and avoid stretching it (DO NOT pull it, tug it
or use it to drag the appliance to which is connected). Before unplugging the
appliance, switch it off, by pressing the Power button.
During operation, DO NOT touch the appliance with wet body parts, and it is
recommended to have between you and the standing surface, an isolating element
(for example, wearing shoes with rubber soles).
DO NOT soak the appliance in water or other liquids, wash it under the tap, or let
any liquid flow into the internal casing of the appliance to prevent electric shock. In
case of accidental fall in water, DO NOT try to take it out, but first of all unplug
immediately the power cable from the socket.
Place the appliance at a proper distance from the objects or surrounding walls
making sure that its functioning will NOT cause accidental damages. There should
be at least 30 cm of free space from the back, left & right sides, and the top of the
appliance. 3

17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
The appliance should NOT be placed on a surface or in the vicinity of objects which
can be damaged by heat, such as carpets or plastics. When using the appliance, the
surface that the appliance is placed upon as well the surface immediately above
(e.g. a wooden cabinet above the appliance), may become very hot. If the appliance
is operated on wooden furniture, use a protective pad to prevent damage to
delicate finishes.
Avoid placing the power cable on abrasive or sharp surfaces or in positions where it
can be damaged easily. The cable must NOT be placed under carpets, or covered
with throw rugs, runners or similar. Arrange the cable away from the high traffic
area, and where it will NOT be tripped over.
Always remember to unplug the power cable of the appliance if it is NOT used for a
long period, before storing, cleaning or performing any maintenance operation.
Avoid carrying out operations which are NOT specified in this manual (such as
disassembling and/or altering).
In case of malfunction or anomaly during the functioning, switch off the appliance
immediately, turn off the power and check the cause of the anomaly, if possible,
with the support of a qualified person.
During the period of operation, high temperature steam will be emitted from the
nozzle. To avoid scalding:
• DO NOT fill the Water Tank with hot water;
• DO NOT fill water beyond the maximum volume indicated;
• DO NOT place the nozzle and the Stainless Steel Panel directly on any surface or
any part of the steamer when the nozzle and the Stainless Steel Panel is hot or
plugged in;
• DO NOT touch any part of the steamer, especially the nozzle and the Stainless
Steel Panel, except the Body when the steamer is hot;
• DO NOT use the steamer on garments while they are still attached to the body;
• DO NOT direct steam at any person or animal & one’s hands and face should be
angled away from the nozzle at all times.
Switch off the steamer and unplug the socket from the electric mains when not in
use and before filling, emptying and cleaning the steamer.
If smoke is observed coming out of the steamer, unplug the power cable
immediately.
This appliance is NOT intended for commercial use but to be used in households
and similar applications, such as:
• Staff kitchen areas in shops, offices and other working environments;
• Dormitories;
• By clients in hotels, motels and other residential environments;
• Bed and breakfast type environment
DO NOT use or store the appliance outdoors. Store and use the appliance only
indoors, or in any case, protected from weathering such as rain, direct radiation of
the sun and dust.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall NOT
play with the appliance. Cleaning and user maintenance shall NOT be made by
children unless they are older than 8 and supervised. Keep the appliance and its
cable out of reach of children less than 8 years old.
Save these instructions.
4

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Before using the steamer, check the pockets of the clothing to be ironed and
remove any loose items held within.
Be aware of any accessories that is attached to the clothing and which can be easily
damaged by steam. For example, it is suggested that the steamer should not be
used around the metal fittings. The high-temperature steam may cause the metal
accessories to fade.
Hang clothes vertically on hangers or racks prior to, and in preparation of, steaming.
Turn the positioning lock of the Water Tank at the bottom of the Main Body to the
Unlocked position, and pull the Water Tank downwards to remove it from the Main
Body.
Fill the Water Tank with water. DO NOT add water in excess of the“MAX” mark
indicated. Thereafter, ensure that the exterior of the steamer is completely dry
before use. (Note: If you require to top-up water, switch off the appliance and
unplug from the electric mains first. DO NOT top-up water while the appliance in
switched ON.)
Push the Water Tank upwards to re-attach it to the Main Body, and turn the
positioning lock of the Water Tank at the bottom of the Main Body to the Locked
position.
Insert the plug of the appliance into the electric mains socket and switch it ON.
Press the Power Button and the Indicator Light illuminates. The steamer starts
heating up.
Preheat for 38 seconds and the appliance is ready to be used. DO NOT press the
Steam Switch during the preheating period.
After the preheating is completed, pressing the Steam Switch releases steam, and
releasing the Steam Switch stops the steam being released. Steam can be produced
continuously by sliding the Steam Lock Slider down.
If you are using the steamer for the first time, pressing the Steam Switch for several
minutes will remove any impurities and odours that may be left during the
manufacturing process.
Keep the nozzle and the Stainless Steel Panel upright and steam only in a vertical
motion, never in a horizontal motion or tilted backwards as doing so may lead to
hot water discharge. The pictures on the following page help illustrate how to iron
correctly using the steamer.
When ironing is completed, press the Power Button again. The Indicator Light goes
out and the steamer is turned OFF. Turn off the switch and unplug the socket from
the electric mains when not in use and before filling, emptying and cleaning the
steamer.
HOW TO USE
5

6

Normal Cleaning
1.
2.
3.
4.
Removing mineral build-up
5.
6.
7.
8.
9.
10.
11.
12.
13.
Ensure that the switch is turned off and unplugged from the socket at the electric
mains. Wait for 60 minutes to allow sufficient time for the appliance to cool before
cleaning the product, installing or disassembling accessories, emptying the Water
Tank (this should be done after every use) or storing the appliance.
Remove the Steam Brush on the head of the steamer and use a wet cloth to clean it.
DO NOT use metal scouring pads, nor or corrosion cleaners.
DO NOT soak the appliance in water or other liquids, wash it under the tap, or let
any liquid flow into the internal casing of the appliance.
Turn the positioning lock of the Water Tank at the bottom of the Main Body to the
Unlocked position, and pull the Water Tank downwards to remove it from the Main
Body. Empty the remaining water from the Water Tank, and wipe the exterior of the
Water Tank and Main Body with a soft, dry sloth before storing the appliance
upright in a dry place.
Add water & vinegar into the Water Tank up to the MAX level. Wait for 40 mins and
then push the Water Tank upwards to re-attach it to the Main Body, and turn the
positioning lock of the Water Tank at the bottom of the Main Body to the Locked
position.
Insert the plug of the appliance into the electric mains socket and switch it ON.
Press the Power Button and the Indicator Light illuminates. The steamer starts
heating up.
Preheat for 38 seconds. DO NOT press the Steam Switch during the preheating
period. After the preheating is completed, press the Steam Switch for 1 minute to
release the mixture of steam and vinegar. Thereafter, release the Steam Switch
which stops the mixture from being released. Steam can be produced continuously
by sliding the Steam Lock Slider down.
Press the Power Button again. The Indicator Light goes out and the steamer is
turned OFF. Turn off the switch and unplug the socket from the electric mains.
Wait for 60 minutes to allow sufficient time for the appliance to cool. Turn the
positioning lock of the Water Tank at the bottom of the Main Body to the Unlocked
position, and pull the water tank downwards to remove it from the Main Body.
Empty the Water Tank of the mixture of vinegar & water and rinse it with clean water.
Refill the Water Tank with clean water.
Push the Water Tank upwards to re-attach it to the Main Body, and turn the
positioning lock of the Water Tank at the bottom of the Main Body to the Locked
position.
Insert the plug of the appliance into the electric mains socket and switch it ON.
Press the Power Button and the Indicator Light illuminates. The steamer starts
heating up.
HOW TO CLEAN
7

14.
15.
16.
17.
18.
Preheat for 38 seconds. DO NOT press the Steam Switch during the preheating
period. After the preheating is completed, press the Steam Switch for 1 minute to
release steam. Thereafter, release the Steam Switch which stops the steam from
being released. Steam can also be produced continuously by sliding the Steam
Lock Slider down.
Press the Power Button again. The Indicator Light goes out and the steamer is
turned OFF. Turn off the switch and unplug the socket from the electric mains.
Wait for 60 minutes to allow sufficient time for the appliance to cool. Turn the
positioning lock of the Water Tank at the bottom of the Main Body to the Unlocked
position, and pull the Water Tank downwards to remove it from the Main Body.
Empty the Water Tank and rinse it with clean water.
Remove the Steam Brush on the head of the steamer and use a wet cloth to clean it.
DO NOT use metal scouring pads, nor or corrosion cleaners.
Wipe the exterior of the Water Tank and Main Body with a soft, dry sloth before
storing the appliance upright in a dry place.
8

PROBLEM SOLVING
How to SolveProblem Possible Causes
Plug the appliance into the electric
mains and switch it on.
The appliance fails
to convert water
into steam.
Indicator light on
steamer does not
illuminate.
The appliance is not
plugged in.
Preheating for 38 seconds before
pressing the Steam Switch.
Keep the steamer vertical.
The appliance fails
to convert water
into steam.
Indicator light on
steamer
illuminates.
Preheating was not
observed before the
Steam Switch was
pressed.
Refill the Water Tank with tap water
or distilled water.
There is a loud
buzz or pumping
sound when the
appliance works.
Low water level in the
Water Tank.
It is normal for the steam to stop
being emitted periodically for a few
seconds. If this persists for longer
durations, follow the steps listed in
the ‘Removing mineral build-up’
instructions contained in the
Instruction Manual.
Steam emitted
intermittently.
Mineral build-up in the
appliance.
Check the household circuit breaker
for any tripped wires.
Call for a qualified electrician.
Household power circuit
has blown.
Follow the steps listed in the
‘Removing mineral build-up’
instructions contained in the
Instruction Manual.
Mineral build-up in the
appliance.
Refill the Water Tank with tap water
or distilled water.
The Water Tank is empty.
Send the appliance to the service
centre for checks.
Fuse on appliance is
blown.
9

This appliance, along with all other electronic appliances, should, when it is no longer capable of
functioning, be disposed with the least possible environmental damage according to the local
regulations in your area. In most cases you can discard the appliance at your local recycling centre.
DISPOSAL: Do not dispose this appliance as unsorted municipal waste.
Collection of such waste separately for special treatment is necessary.
Risk of child or animal entrapment
Before you discard this appliance, please remove all doors and leave the shelves inside so that
children or animals may not easily get trapped inside.
ENVIRONMENTAL TIP
Warranty Conditions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
This warranty provides against defective materials and manufacturing faults throughout for
two years from the date of purchase of the appliance. The warranty on the Compressor is 10
years subject to the same conditions as above.
This warranty also does not cover normal wear and tear, replacement of consumable
materials and accessories, and the cost of maintenance of the appliance.
This warranty does not cover the repair or replacement of part/s damaged by misuse,
accidents, negligence, alterations, or modifications in any way, or repairs done by any repair
organisation without the prior consent of PowerPac Electrical Pte Ltd.
Repair and service are to be performed at: 5 Changi South Lane #03-01 Singapore 486045.
A transport fee will be charged for personal doorstep service.
The original purchaser of the appliance must furnish proof of purchase to our Service Centre
with the email or number as registered during submission of warranty when this appliance is
sent for repair/service. Failure to do so may delay the receipt of said repair/service by the
customer.
Under no circumstances whatsoever shall the serial number be erased, defaced or altered by
the customer and/or his representatives, or the dealer and/or his agents. Failure to ensure
this shall invalidate the warranty.
This warranty is deemed to be void if the defect is cause by the attack of household pests,
fire, lightning, natural disasters, pollution, abnormal voltage or the usage of generators.
This warranty is valid in Singapore only.
This warranty will be honoured subject to the customer’s registration of the warranty
inclusive of original invoice or valid purchase receipt. Failure to present these documents will
result in denial of service. However, if the customer still requests that the defective appliance
be repaired, PowerPac Electrical Pte Ltd may, at its discretion, repair the appliance but impose
a labour charge, as well as the costs of the replacement parts, to be borne solely by the
customer.
Please refer to the attached picture for the location of one of our appliance’s serial number,
as an example.
Please complete the on-line registration warranty form available
on our website. There is no further requirement to send us any
hard copy as part of our efforts to save the environment.
In accordance with the terms and conditions of this limited
warranty as stated above, PowerPac Electrical Pte Ltd, at its
expense shall provide free services for the appliance within the
warranty period from its date of purchase from our Authorised
dealers.
WARRANTY
E-Register scan
10

PPIN617
MODEL
220-240V ~ 50/60Hz
VOLTAGE
1650W
POWER
SPECIFICATION