PR Lighting Theatre Master PR-3010 User manual

THEATRE MASTER
PR-3010
This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.
PR LIGHTING LTD.
Yingbin Road, Dashi Panyu, Guangzhou, 511430 China
http://www.pr-lighting.com

2/12
Theatre Master manual.doc
SECTION PAGE
SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER CONNECTIONS 4
OPERATION 4
STAND-ALONE MODE 5
XLR CONNECTIONS AND TERMINATOR 5
CONTROLLER MODE –DMX 512 OPERATION 6
MAINTENANCE 8
KEEPING THE PROJECTOR CLEAN 8
TROUBLESHOOTING 9
TECHNICAL DATA 9
ELECTRICAL DIAGRAME 10
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change
without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the
course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any
consequence arising from them.
Every apparatus has been tested completely and packed properly by the manufacturer. Please make sure the packing and / or
the apparatus is in good condition before your installation and use. Should there be any damage caused by transportation,
consult your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the
manufacturer and / or dealer.
THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR
Bracket (1 PCS)
Locking knob (2 PCS)
XLR plug (1 PCS)
XLR socket (1 PCS)
This manual (1 PCS)
Thank you for purchasing the product Theatre Master, PR-3010.
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place for
future reference.
The Theatre Master is an innovative projector with an elegant housing made from high quality
aluminiun-alloy with an epoxy paint finish. The Theatre Master complies to CE norms and standards
and uses international protocol DMX-512.
The Theatre Master uses HMI 1200 lamp and high quality optical systems which produce bright and
beautiful light beam, and it can continuously adjust the brightness from 0% to 100% via the mechanical
device. The Theatre Master features strobe, soft light beam, mixing colours, iris adjustable and
rainbow effect, so it is suitable for use in TV station, disc, singing and dancing stage, night club and so
on.
The projector has protection devices of auto thermal cut-off and lamp power cut-off. In case you
directly open the cover for lamp replacing before switching off the general switch, the lamp will be cut
off to protect your eyes.
ACCESSORIES
INDEX
INTRODUCTION

3/12
Theatre Master manual.doc
The following points are important for safety as well as for the smooth
installation and performance of the unit.
When unpacking and before disposing of the package check there is no transportation damage before
using the projector. Should there be any damage caused by transportation, consult your dealer and do
not use the apparatus. Keep the package well for your possible future transportation.
The projector is for indoor use only, IP 20. Use only in dry locations. Keep this device away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or
metallic objects.
The projector is not designed or intended to be mounted directly on to inflammable surfaces.
The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that all the cooling fans run normally and no ventilation slots are blocked.
Do not project the beam onto inflammable surfaces, minimum distance is 3m. 3m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and / or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power
requirements of the projector. Only use the lamp with the specified type and rating.
It is essential that each projector is correctly earthed and that electrical installation conforms to all
relevant standards.
Do not connect this device to any dimmer pack.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord
come into contact with other cables. Only handle the power-cord by the plug. Never pull out the plug
by tugging the power-cord.
Keep the lamp clean. Do not touch the lamp glass with bare hand.
The lamp used in this projector is an high power discharge lamp. After being switched off don’t attempt
to restart the projector until lamp has cooled, this will require approx 15 minutes. Switching the lamp on
and off at short intervals will reduce the life of both the lamp and the projector. Occasional breaks will
prolong the life of both the lamp and the projector.
Never run the projector without a lamp.
There are no user serviceable parts inside the projector, do not open the housing and never operate
the projector with the covers removed.
Always disconnect from the mains, when the device is not in use or before cleaning it
or before attempting any maintenance work.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
SAFE USAGE OF THE PROJECTOR

4/12
Theatre Master manual.doc
This unit has been designed to be hung. Mount the bracket provided on the body of the projector via 2
locking knobs, then suspend the projector via its bracket using a M12 size bolt and a nut. When you
want to adjust the angle of the body of the projector, you only loosen the 2 locking knobs carefully and
then adjust the angle of the body. After finishing that, it is recommended that you don’t forget to
retighten the two knobs. Always ensure that the projector is firmly positioned to avoid vibration and
slipping, and always ensure that the structure to which you are attaching the projector is secure and is
able to support a weight of 23Kg for each Theatre Master.
Remove the cover by undoing a M4 knurled screw.
Insert the lamp in the lamp-holder, and ensure the little bubble on the lamp is at a right angle (90°) to
the beam path. Keep the lamp clean during installation.
Reinstall the cover and tighten the M4 knurled screw.
NOTE: The HMI series are high pressure lamps with external igniters (). Care should always be
taken when handling these lamps. Always read the manufacturers "Instructions for use" enclosed with
the lamp.
The unit is supplied with a power cord. Should any other connections be required they must be carried
out with the following configuration.
Earth = Green/Yellow cord
Neutral = Blue cord
Neutral = Brown cord
When the power is switched on, the apparatus automatically starts to run the programmes of self test.
After finishing these, the apparatus is ready for operation.
SETUP OPTIONS
To set the setup options, press the DIP switchs with the 6
numbers as shown below.
No. 1 switch ON, colours rainbow effect enable
No. 1 switch OFF, colours rainbow effect disable
No. 2 switch ON, colours flowing enable
No. 2 switch OFF, colours flowing disable
No. 3 switch ON, shutter function enable when colours changing
No. 3 switch OFF, shutter function disable when colours changing
No. 4 switch: Not used
No. 5 switch: Not used
No. 6 switch: Not used
FITTING THE LAMP
OPERATION
INSTALLING THE PROJECTOR
POWER CONNECTIONS

5/12
Theatre Master manual.doc
Without connecting the controller, regulating the DIP
switch as shown below, the apparatus will run in stand-
alone mode.
In stand-alone mode, the projector will run automatically
the built-in programmes.
XLR CONNECTORS
Connection between controller and projector and between one projector and another must be made
with 2 core screened cable, with each core having at least a 0.5mm diameter. Connection to and from
the projector is via cannon 3-pin XLR plugs and sockets which are included with the projector. The
XLR's are connected as shown in the table above.
Note, care should be taken to ensure that none of the connections touch the body of the plug or each
other. The body of the plug is not connected in any way. The Theatre Master accepts digital control
signals in standard DMX512 (1990) format.
5-PIN AND 3-PIN CONVERSION
Theatre Master uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you
should convert 5-pin plug / socket into 3-pin socket / plug as shown below.
XLR CONNECTORS AND TERMINATOR
STAND-ALONE MODE

6/12
Theatre Master manual.doc
DMX TERMINATOR
In the Controller mode or Master/Slave mode, the DMX output has to be connected with a DMX
terminator at the last fixture in the chain. This prevents electrical noise from disturbing and corrupting
the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2
and 3, which is then plugged into the output socket on the last projector in the chain. The connections
are illustrated below.
CONNECTING CONTROLLER WITH PROJECTORS
Connect the controller’s output to the first luminaire’s input, and connect the first luminaire’s output to
the second luminaire’s input. The rest may be deduced by analogy. Eventually connect the last
luminaire’s output to a DMX terminator as shown below.
CONTROLLER MODE -DMX 512 OPERATION

7/12
Theatre Master manual.doc
TABLE FOR SETTING THE DIP SWITCHES
Each unit must be given an address so that the correct projector responds to the correct control
signals. The following table lists the setting codes of the address of the DIP switches, and the
luminaires are from No.1 to No.128. Each unit has 10 DIP switches with the numberS of #1, #2, #3, #4,
#5, #6, #7, #8, #9 and #10. (For the Theatre master, set all #10 switches on the “OFF”.)
In the table, “0” means the switch is on the “OFF”, and “1” on the “ON”.
For example, if you want to look up the address setting of the No 50 luminaire, you will find the NO 50
luminaire row (#1, #2, #3, #4, #5) with the codes of “1”, “0”, “1”, “0” , “0” and column (#6, #7, #8, #9)
with the codes of “0”, “1”, “1” , “0”. So set the #1, #3,#7 and #8 switches on the “ON”, and set the #2,
#4, #5, #6, #9 and #10 switches on the “OFF”.
#9
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Setting Table of
Address Switches
#8
0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
0=OFF #7
0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
1=ON #6
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
#1 #2 #3 #4 #5
0 0 0 0 0
1 0 0 0 0 1 9 17 25 33 41 49 57 65 73 81 89 97 105 113 121
0 1 0 0 0
1 1 0 0 0
0 0 1 0 0
1 0 1 0 0 2 10 18 26 34 42 50 58 66 74 82 90 98 106 114 122
0 1 1 0 0
1 1 1 0 0
0 0 0 1 0
1 0 0 1 0 3 11 19 27 35 43 51 59 67 75 83 91 99 107 115 123
0 1 0 1 0
1 1 0 1 0
0 0 1 1 0
1 0 1 1 0 4 12 20 28 36 44 52 60 68 76 84 92 100 108 116 124
0 1 1 1 0
1 1 1 1 0
0 0 0 0 1
1 0 0 0 1 5 13 21 29 37 45 53 61 69 77 85 93 101 109 117 125
0 1 0 0 1
1 1 0 0 1
0 0 1 0 1
1 0 1 0 1 6 14 22 30 38 46 54 62 70 78 86 94 102 110 118 126
0 1 1 0 1
1 1 1 0 1
0 0 0 1 1
1 0 0 1 1 7 15 23 31 39 47 55 63 71 79 87 95 103 111 119 127
0 1 0 1 1
1 1 0 1 1
0 0 1 1 1
1 0 1 1 1 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128
0 1 1 1 1
1 1 1 1 1

8/12
Theatre Master manual.doc
DMX CONTROL CHANNEL FUNCTIONS
The Theatre Master has 4 channels. They are shown in the following table.
CHANNEL DMX VALUE DESCRIPTION
1 Iris 0-255 Iris adjust from small to large
0-15 White
16-31 Red
32-47 Yellow
48-63 Violet
64-79 Green
80-95 Orange
96-111 Blue
112-127 Pink
2Colour
128-255 Colours change from slow to fast till rainbow effect
0-31 White
32-63 Soft light
64-95 Weak light
96-127 Orange
128-159 Blue
160-191 Yellow
192-223 Pink
3
Colour
temperature/
Colour
224-255 Yellow
0-15 Shutter/blackout
16-125 Adjust light in linear from shutter to fully open
126-139 Open fully
140-243 Strobe movement from slow to fast
4
Dimmer
244-255 Open fully
If the lamp becomes damaged or deformed in any way it must be replaced. If the light from the lamp
appears dim this would normally indicate that it is reaching the end of its life and it should be changed
at once, old lamps run to the extremity of their life can explode. If the projector does not function,
check the fuse at the rear of the projector, it should only be replaced by fuse of the same specified
value 20A/250V (fast blow, 6mmx30mm). On the main PCB inside the projector there is also a fuse
rated 2A/250V (fast blow, 5mmx20mm). Should these be damaged call a qualified technician before
replacement. The projector has thermal protection device that will switch off the projector in case of
overheating, should this operate, check that the fans are not blocked, and if they are dirty clean them
before switching on the projector again. Check that the fans are operational, if not call a qualified
technician.
Any maintenance work should only be carried out by a qualified technician.
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should
be cleaned every 15 days. The dichroic colour filters should also be regularly cleaned to maintain an
optimum light output. Do NOT use any type of solvent on dichroic colour filters.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or
particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth
and typical glass cleaning products should be used in cleaning.
Do not use any organic solvent, e.g. alcohol, to clean the housing of the projector.
MAINTENANCE
KEEPING THE PROJECTOR CLEAN

9/12
Theatre Master manual.doc
PROBLEM RESOURCE
The projector does not start Check that the fuse is not blown.
Check that the lamp is ok.
The projector switches on but does not
answer to commands Check the DIP switches are correctly set. Check the XLR cable is good.
The projector only functions
intermittently Check the fans are working and not dirty.
The beam appears dim Check the lamp is not at the end of its life.
Power supply: 230V AC 50Hz
Optional: 240V, 220V, 200V AC 50/60Hz
Power consumption: 1400W at 220V
Lamp: HMI 1200W, double ends
Colours: 7 didichroic colours + white
Rainbow effect at variable speeds
Iris: Continuously variable low noise iris
Frost: 2 frost filters
Colour temperature: Normal 5600°K, adjustable high 6000°K and low 3200°K
Shutter/strobe: 1-7 F.P.S.
Control operation: Stand-alone, DMX Controller
Protocol: Standard DMX 512
DMX channels: 4 channels
Dimensions: 680mm LONG x 350 WIDE x270mm HIGH
Weight: 23 kg
Others: Linear dimming from 0-100%, thermal cut-off protection, manual focus
TECHNICAL DATA
TROUBLESHOOTING

10/12
Theatre Master manual.doc
LIGHT OUTPUT
ELECTRICAL DIAGRAM

11/12
Theatre Master manual.doc

12/12
Theatre Master manual.doc
PR LIGHTING LTD.
Yingbin Road, Dashi, Panyu, Guangzhou, China
Post-Code: 511430
TEL: [phone]
FAX: [phone]
P/N: 320040026
Last Revision: 24:02:2004