Precor Elliptical Fitness Crosstrainer Experience 700... User manual

Experience™ Series 700 Line
Elliptical Fitness Crosstrainer™ (EFX)
Assembly Guide
Equation 1:E nglis h

Table of Languages
English..................................................................................................................................................................1
3

EFX Assembly Guide
Follow the steps in the order listed in this assembly guide. For more product
information, visit us at www.precor.com.
WARNING
At least two people are required to assemble the equipment. DO NOT
attempt assembly by yourself.
Assembly requirements
Important Before you fully tighten a fastener, check that its head is flush with the surface
of the equipment. If not, cross-threading may have occurred. DO NOT attempt to rework the
assembly as more damage to the equipment will occur. Instead, contact Customer Support at
www. precor.com
We recommend you:
•Assemble the equipment close to where you plan to use it.
•Assemble the equipment on a solid, flat surface, so that it remains level and
stable.
•Locate the equipment at least 19.7 inches (0.5 meter) away from walls or
furniture on either side of the equipment, and 19.7 inches (0.5 meter) away
from objects behind or in front of the equipment.
•DO NOT move the equipment without assistance.
4

Required tools
•#1 Phillips head screwdriver
•Fish tape (optional)
•Hex wrenches
3/16-inch
5/32-inch
1/2-inch
9/16-inch
Hardware kit
Component Quantity Torque Component Quantity Torque
Washer head screw
(5/16 x 3/4-inch)
2 204 in-lb Self tapping pan
head screw
(1/4 x .50)
9 20 in-lb
Flat head socket head
cap screw for console
mounting
(1/4 x .625)
5 96 in-lb Self tapping pan
head screw
(#8 x .50)
2 15 in-lb
Grommet (1/4-inch) 7 Self tapping pan
head screw
(#10 x 5/8)
4 15 in-lb
Dog point set screw
(3/8 x 1.25-inch)
3 300 in-lb Clip nut 2
Note There may be extra hardware included with the EFX.
5

Begin Assembly
WARNING
DO NOT attempt to connect electrical power until all assembly procedures are complete and console is properly installed.
DO NOT fully tighten the fasteners until instructed to do so.
To begin assembly:
1. Remove the two bolts, two flat washers, and two nuts from the ramp and set them
aside.
2. Slide the console frame into the ramp and base frame.
Important DO NOT pinch or crush the cable during assembly.
3. Attach the console frame to base frame using two bolts . Hand tighten the bolts.
Figure 1
4. Secure the console frame to the ramp using two bolts from the top and two lock
nuts.
Figure 2
5. Have your assistant pull the console frame forward while you tighten the
ramp bolts using one wrench on the bottom nut and one on the top bolt.
Tighten to 204 in-lb of torque.
Important DO NOT skip this step. It is required to ensure proper assembly.
Figure 3
6. Fully tighten the base frame bolts.
7. Using a fish tape, pull the power cable from the ramp, up through the
console frame, and out the top.
Figure 4
6

To attach the moving arms:
1. Slide the moving arm into the arm frame and attach the arm using a dog
head bolt and fully tighten using a 3/16 hex wrench.
Note The arms are labeled Left and Right.
Figure 5
2. Fit an inner link cover onto the link arm.
Figure 6
3. Screw the link arm into the base of the moving arm.
4. Screw the link arm into the base of the moving arm (the bolt shops
installed in the link arm assembly).
5. Fit the outer Link cover onto the link arm and attach it using a Phillips
head screw .
Figure 7
6. Perform these steps to attach the other arm.
Note If you are going to mount a PVS or networked console, route those
cable through the frame at this time.
7

Attach the covers
The EFX ships with the following cover parts: Two side covers, one front cover,
and two cover retention brackets.
Attaching the plastic covers:
1. Insert seven plastic grommets into the frame in following locations:
Figure 8
2. Attach the base cover by fitting its plastic tab into the base frame, then slide the
cover forward and downward to snap it into place.
Figure 9
3. Attach the base cover using two screws .
4. Attach the front of the base plastic using two screws .
Figure 10
8

There are latches on the plastic covers that must be engaged to ensure a good
fit. Review the follow procedure before starting the cover assembly.
To attach the side covers:
1. Position one of the side covers against the console frame with its ramp latch
setting on top of the ramp and its wing edge fitted into the arm as shown
below.
Important Flex the plastic to fit it against the frame. DO NOT pinch or crush
the cable during assembly.
Figure 11
2. Position the second side cover against the console frame.
3. Identify where the covers join on the bottom and press upward to snap the
internal latch together.
Figure 12
4. Press the top of the covers together to engage the top internal latch.
Figure 13
5. Snap a pivot bracket onto the boss of each side cover and then attach each
bracket using two screws .
Note The bracket should fit tightly against the assembly.
Figure 14
9

To complete the cover assembly:
1. Secure each side cover using one screw .
Figure 15
2. Position the display front cover so that the two internal hooks are engaged
with the inside bottom of the side covers.
Figure 16
3. Using both hands, pull the front cover forward to snap it into place.
Figure 17
4. Press the front cover upward to close the gap between the covers and
secure it using two screws .
Note If the clip nuts are missing from your front cover, use the extra
clip nuts included in your hardware kit.
Figure 18
5. Position the top cover so that the two top latches fit into the top of the side
covers. Rotate it downward into place.
Figure 19
6. Secure it using one screw .
Figure 20
To complete the console installation, refer to the installation guide
shipped with your console.
10