Prince Castle 296 Series User manual

Operating
Instructions
355 East Kehoe Blvd. • Carol Stream, IL 60188 USA
Telephone: [phone] • Fax : [phone]
Toll Free: 1-800-PCASTLE
www.princecastle.com
197-538revC-EN Printed in USA 6/06 © 2006
Vertical Contact Toaster
296 & 297 Series
Electrical Specifications
Table of Contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 – 8
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Volts Hz Watts Amps
230 60 1700 7.5
110/120 60 1700 15.5
220 50/60 1700 7.5
Limited Warranty
This product is warranted to be free from defects in
material and/or workmanship for a period of 1 year from
date of original installation, not to exceed 18 months
from the date of manufacture.
Any component which proves to be faulty in material
and/or workmanship will be replaced or repaired (at the
option of Prince Castle, Inc.) without cost to the
customer for parts and labor. This warranty covers on
location service (i.e. trip charges and/or mileage). Travel
mileage is limited to 100 miles (200 Kilometers) round
trip (one trip warranty) from an authorized service
agency or its sub-service agency.
This warranty is subject to the following exceptions/
conditions:
• Use of any non-genuine Prince Castle parts voids
this warranty.
• All labor to be performed during regular work hours.
Overtime premium (the incremental amount) will be
charged to the customer.
• Damage caused by carelessness, neglect and/or
abuse (e.g., dropping, tampering or altering parts,
equipment damaged in shipment, by fire, flood or an
act of God) is not covered under this warranty.
• All problems due to operation at voltages other than
that specified on equipment nameplates are not
covered by this warranty. Conversion to correct
voltage is the customer’s responsibility.
• This equipment must be serviced by Prince Castle
Authorized Service Agency or a Prince Castle
Service Technician during the warranty period.
• Normal adjustments as outlined in this manual are
not covered under warranty.
• Motors that fail due to the lack of monthly lubrication
will not be covered under warranty.

Printed in USA 6/06 © 2006 2 197-538revC-EN
Installation
1. After you have removed the toaster from the carton,
inspect the unit for signs of damage. If there is damage
to the unit:
• Notify carrier within 24 hours after delivery.
• Save carton and packing material for inspection
purposes.
• Contact your Prince Castle dealer or the
Prince Castle Customer Sales Department at
1-630-462-8800 if purchased directly.
2. Verify that all parts have been received.
• Slim-Line Bun Toaster and conveyor assembly.
• Release Sheet Kit — located in a 14" box.
• Crumb Tray — taped to the front of the conveyor.
3. Place toaster on flat surface. Remove protective
covering.
4. Lift conveyor off conveyor guide rails and set aside.
Remove all packing materials (nylon tape, foam block,
plastic coating on sheet metal, and black rubber
packaging spacers) from conveyor and conveyor
guides.
Figure 1
5. Place the Teflon sheet over the top of the platen
housing, making sure to have three inches of overhang.
Figure 2
6. Slide the release sheet holding bracket onto the top of
the platen housing.
Figure 3
7. Attach conveyor to the toaster by sliding the four pins
(conveyor slides) on the conveyor housing into the four
conveyor guides. Lower the conveyor housing until it is
securely in place.
8. Hook the back end of the crumb tray onto the bar
located below the conveyor assembly.
9. Plug unit into a grounded receptacle.
Operation
1. Turn the Power switch to the “On” position. The orange
indicator light will illuminate. Allow 30 minutes for platen
to reach operating temperature.
Figure 4
2. Place a sample run of the product being toasted into
the top of the conveyor housing. The side to be toasted
should face the platen.
Figure 5
3. The toasted product will be dispensed automatically
from the bottom of the conveyor assembly.
4. Verify that product meets acceptable standards. If not,
see adjustment section.
Conveyor Guides
3-inch Overhang
Release Sheet
Holding Bracket
Power Switch

197-538revC-EN 3 Printed in USA 6/06 © 2006
Adjustments
Conveyor and Motor Gears:
There will be a 1/64" clearance between the conveyor gear
and motor gear when properly aligned. Improper alignment
will cause the conveyor to periodically bind.
Figure 6
1. Working from the “back side” of the toaster, loosen the
2 setscrews at the bottom of the conveyor guide until
they are even with the conveyor stop. Note: the
conveyor assembly may need to be removed for easier
access.
2. Use the Allen Wrench to tighten the left setscrew (end
housing side) until the setscrew just touches the
conveyor slide.
Figure 7
3. Tighten the right setscrew (motor housing side) until
the bottomof the conveyor housing is parallel to the top
of the base.
4. Carefully tighten each setscrew another 1/2 turn.
5. Remove the conveyor assembly.
6. Apply a drop of wicking grade thread locking fluid to
each setscrew.
7. Replace conveyor assembly.
Bun Compression:
The toaster platen can be adjustedto provide the necessary
compression needed on various products.
• Turn the two platen adjustment knobs clockwise to
compensate for use on thicker bread products. Turn
the two platen adjustment knobs counterclockwise
for thinner products. The numbers on thefront of the
endandmotorhousingwillindicatethesettings, 1 for
thinnest product, 5 for thickest.
Figure 8
Figure 9
Platen Temperature:
The temperature of the platen can be adjusted to
compensate for darker or lighter toasting requirements.
• Turn the thermostat adjustment knob clockwise for
darkertoasting.Turnthethermostatadjustmentknob
counterclockwise for lighter toasting.
IMPORTANT:
Allow 15 minutes for toaster to stabilize after
adjusting the thermostat.
Tools Needed: 3/32" Allen wrench
Wicking grade thread locking fluid
1/64" Clearance Gears
Properly
Mesh
Top of the #10-32 Setscrew
Both Sides
3/32 Hex
Head Key
Thermostat Knob
Platen Adjustment
Knobs
THICKER
5
4
3
2
1
THINNER

Printed in USA 6/06 © 2006 4 197-538revC-EN
Cleaning
CAUTION: This is not jet-water approved, and
should not be cleaned with a water hose or jet
spray.
CAUTION: Do not immerse in water.
1. Turn off the Power switch and unplug the toaster.
2. Allow platen to cool for 60 minutes before cleaning.
3. Remove the conveyor assembly.
4. Wipe the conveyor with a damp cloth. For the chain use
a soft bristle brush.
5. Remove the release sheet and lay it on a flat surface.
Thoroughly clean both sides with a damp cloth making
sure all carbon buildup is removed. Allow to air dry.
IMPORTANT:
Rotate two sheets daily for longer life. Sheets
last 4 – 6 months based on care and volume of product
toasted.
6. Use a damp cloth to remove any carbon buildup on the
platen surface.
IMPORTANT: Do not use sharp objects, Scotch Brite pads,
scouring pads, or abrasive cleaners on the platen or Teflon
release sheets as it will cause irreparable damage.
Preventive Maintenance (Motor)
To extend the life of your replacement motor, have an
authorized factory service technician or store manager wick
the shaft of the motor with 2-3 drops of oil every 3,000 hours
of run time.
IMPORTANT: Unplug toaster before performing any
preventive maintenance.
Figure 10
Shaft

197-538revC-EN 5 Printed in USA 6/06 © 2006
Troubleshooting
Front View Parts List
* Not shown.
PROBLEM PROBABLE CAUSE SOLUTION
Unit will not heat up. No power to unit. Ensure power cord is connected to proper
receptacle and the power inlet.
Power rocker switch light off. Inoperable power cord. Replace power cord.
Loose connection on power switch. Tighten power switch connections.
Inoperable power switch. Replace power switch.
Unit will not heat up. Inoperable thermostat. Replace thermostat.
Power rocker switch light on. Inoperable platen. Replace platen.
Unit heats up, but the conveyor
does not run. Loose motor switch connection. Tighten motor switch connection.
Inoperable motor. Replace motor.
Stripped drive gear. Replace drive gear.
Loose chain sprockets. Adjust and tighten sprockets.
Gears not meshing. Adjust conveyor setscrews (see Conveyor and
Motor Gears on page 3).
Inoperable motor switch. Replace switch.
Unit under- and over-heats
(does not respond tothermostat
adjustments).
Inoperable thermostat. Replace thermostat.
Buns under or over done. Check platen adjustment. (See Bun
Compression on page 3.) Adjust platen for proper compression.
Check platen temperature. (See Platen
Temperature on page 3.) Adjust thermostat for proper temperature.
5
2
4
3
1
Item Part Number Description
178-184S Power Lighted Rocker Switch
2197-185S Platen Adjustment Knob (Pkg of 2)
370-012 Thermostat Knob
4197-232S Foot (Pkg of 4)
5197-124 Conveyor Guide with Handle
* 197-475 Overlay (Motor Housing)
*197-259 Release Sheet Conversion Kit,
197/297
*197-402 Release Sheet (Pkg of 2)
Conversion Kit 296 Series
*297-151 Release Sheet (Pkg of 4)
297-T12PHH only
*297-149 Clamp Bar
297-T12PHH only
*197-260 Release Sheets (Pkg of 2),
297 Series

Printed in USA 6/06 © 2006 6 197-538revC-EN
Conveyor Assembly
Parts List
10
11
454
2
3
1
4
776
4
1
3
2
9
8
Item Part Number Description
1197-463S Left and Right Side Shaft Carrier
Assy
2197-459S Left and Right Side Shaft Carrier
Adjustment Assy
381-015 Compression Spring
4 197-467 Conveyor Slide
5197-280 Shaft Assy.
Item Part Number Description
6197-465 Driven Shaft
7197-302 Sprocket Kit (Pkg of 2)
889-684 Complete Chain Assy
9 89-590 Single Conveyor Chain Link
10 197-7S Black Handle with Screw
11 197-466S Complete Conveyor Assy (Passive)

197-538revC-EN 7 Printed in USA 6/06 © 2006
Rear View
Parts List
12 13
2
11
10
9
8
17
4 Places
6
1
4
5
3
16
15
14
Item Part Number Description
1197-436S Gear Kit (20/40 Second)
197-476S Gear Kit (12 Second)
197-477S Gear Kit (14 Second)
197-437S Gear Kit (30 Second)
196-026S Gear Kit (55 Second) (196-Jack)
2 197-114 Motor Cover
3 197-473 End Housing
476-225 Slotted Pan Head Screw
5197-131 Guard
6197-33 Crumb Tray
197-497 Crumb Tray (297-T12PHH only)
873-007 Hex Nut
197-16 Conveyor Stop
76-165 Setscrew
9 76-640 Screw
10 197-96 Left Side Bun Fence
Item Part Number Description
11 73-008 Self Locking Hex Nut
73-030 Hex Nut
79-016 Flat Washer
76-033 Slotted Flat Head Screw
12 76-640 Screw
13 197-13 Lead Pan Weldment
14 197-97 Right Bun Fence
15 197-431S Platen (220 Volt) (297)
197-430S Platen (110 Volt) (297)
196-023S Platen (110 Volt) (296)
16 197-95 Tray Support
17 72-232S Line Cord (CE)
72-233S Line Cord (GB)
72-280S Line Cord (120 Volt)
* Instruction Card for 297-T12PHH
* Part not shown.

Printed in USA 6/06 © 2006 8 197-538revC-EN
Internal Components Parts List
12
11
10
1
9
13
1
8
7
5
4
3
2
6
Item Part Number Description
1 76-300 Slotted Pan Head Screw
2 87-028AS Motor (208-240 Volt)
87-029S Motor (120 Volt)
373-031 Hex Nut
4 79-033 Washer
576-051 Slotted Binder Head Screw
6 79-055 Flat Washer
776-040 Slotted Binder Head Screw
79-017 Split Lock Washer
73-030 Hex Nut
8 76-150 Slotted Pan Head Screw
79-094 Flat Washer
9 79-016 Flat Washer
76-095 Slotted Binder Head Screw
10 197-90 LH Side Plate Weldment with
Adjustment Screw
197-89 RH Slide Plate Bracket with
Adjustment Screw
11 197-428 Baffle (Motor Housing)
197-429 Baffle (End Housing)
12 196-19 Housing
13 197-140 Thermostat with Knob
297-010S Thermostat with Knob and Thermo
Compound

355 East Kehoe Blvd. • Carol Stream, IL 60188 USA
Telephone: [phone] • Fax : [phone]
Toll Free: 1-800-PCASTLE
www.princecastle.com
197-538revC-EN Printed in USA 6/06 © 2006
Wiring Diagram
Voltage Connection
High Voltage Connection (220-240 Volts) Low Voltage Connection (200-208 Volts)