Pro-Form Le Tour De France PFEVEX71919.0 User manual

USER’S MANUAL
CAUTION
Read all precautions and
instructions in this manual before
using this equipment. Keep this
manual for future reference.
Model No. PFEVEX71919.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal
iconeurope.com
CUSTOMER SERVICE
UNITED KINGDOM
Call: 0330 123 1045
From Ireland: 053 92 36102
Website: iconsupport.eu
E-mail: [email protected]
Write:
ICON Health & Fitness, Ltd.
Unit 4, Westgate Court
Silkwood Park
OSSETT
WF5 9TT
UNITED KINGDOM
AUSTRALIA
Call: 1800 993 770
E-mail: [email protected]
Write:
ICON Health & Fitness
PO Box 635
WINSTON HILLS NSW 2153
AUSTRALIA

2
This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, see the front cover of this manual
and request a free replacement decal.
Apply the decal in the location shown.
Note: The decal(s) may not be shown at
actual size.
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS..................................................................3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO USE THE TRAINING BIKE ...........................................................12
MAINTENANCE AND TROUBLESHOOTING.....................................................26
EXERCISE GUIDELINES ....................................................................27
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
RECYCLING INFORMATION ......................................................... Back Cover
WARNING DECAL PLACEMENT
TABLE OF CONTENTS
PROFORM and IFIT are registered trademarks of ICON Health & Fitness, Inc. LE TOUR DE FRANCE is a regis-
tered trademark of Société du Tour de France. Google Maps is a trademark of Google Inc. The Bluetooth®word
mark and logos are registered trademarks of Bluetooth SIG, Inc. and are used under license. Wi-Fi is a registered
trademark of Wi-Fi Alliance. WPA and WPA2 are trademarks of Wi-Fi Alliance.

3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read all
important precautions and instructions in this manual and all warnings on your training bike before
using your training bike. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
1. It is the responsibility of the owner to ensure
that all users of the training bike are ade-
quately informed of all precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
3. The training bike is not intended for use by
persons with reduced physical, sensory, or
mental capabilities or lack of experience and
knowledge, unless they are given supervi-
sion or instruction about use of the training
bike by someone responsible for their safety.
4. Use the training bike only as described in
this manual.
5. The training bike is intended for home use
only. Do not use the training bike in a com-
mercial, rental, or institutional setting.
6. Keep the training bike indoors, away from
moisture and dust. Do not put the training
bike in a garage or covered patio, or near
water.
7. Place the training bike on a level surface with
at least 2 ft. (0.6 m) of clearance around the
training bike. To protect the floor or carpet
from damage, place a mat under the training
bike.
8. Inspect and properly tighten all parts each
time the training bike is used. Replace any
worn parts immediately.
9. Keep children under age 16 and pets away
from the training bike at all times.
10. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the training bike. Always wear
athletic shoes for foot protection.
11. The training bike should not be used by
persons weighing more than 330 lbs.
(150 kg).
12. Be careful when mounting and dismounting
the training bike.
13. Always keep your back straight while using
the training bike; do not arch your back.
14. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.

4
Congratulations for selecting the revolutionary
PROFORM®LE TOUR DE FRANCE®training bike.
The LE TOUR DE FRANCE training bike is unlike any
ordinary exercise bike. With full adjustability, a Wi-Fi®
cycling console, an incline system that simulates actual
road terrain, and an array of other innovative features,
the LE TOUR DE FRANCE training bike is designed to
let you enjoy the outdoor cycling experience indoors.
For your benefit, read this manual carefully before
you use the training bike. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Saddle
Shifter
Saddle Carriage
Adjustment Handle
Adjustment Handle
Handlebar
Tray
Adjustment Handle
Wheel
Pedal/Strap
Console
Leveling Foot
Power Switch
Length: 5 ft. 4 in. (163 cm)
Width: 2 ft. 1 in. (64 cm)
Weight: 121 lbs. (55 kg)
BEFORE YOU BEGIN

5
M6 x 16mm
Screw (110)–4
M4 x 10mm
Screw (116)–2
M10 x 58mm
Screw (74)–4
M4 Washer
(54)–1
M4 x 14mm
Screw (117)–1
M4 x 12mm
Screw (111)–4
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.

6
2
22
74
A
1
2. Remove and discard the indicated shipping
insert (A). If there are shipping screws in the
Front Stabilizer (22), remove and discard
them.
Attach the Front Stabilizer (22) to the Base (1)
with two M10 x 58mm Screws (74).
ASSEMBLY
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish all assembly steps.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• To identify small parts, see page 5.
• In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
Assembly may be easier if you have your own set
of wrenches. To avoid damaging parts, do not use
power tools.
1
1. To register your product and activate your
warranty in the UK, go to iconsupport.eu. If
you do not have internet access, call Customer
Service (see the front cover of this manual).
To register your product and activate your
warranty in Australia, email or post the
following information to the email address or
postal address on the front cover of this manual.
• your receipt (make sure to keep a copy)
• your name, address, and telephone number
• the model number, serial number, and name
of your product (see the front cover of this
manual)

7
2
3
B
47
3
3. If there are shipping screws in the Rear
Stabilizer (23), remove and discard them.
Attach the Rear Stabilizer (23) to the Base (1)
with two M10 x 58mm Screws (74).
74
23
1
4. Using a plastic bag to keep your fingers clean,
apply some of the included grease to the sides
of the channel on the top of the Saddle Post (3).
Next, orient the Saddle Post (3) so that the
height indicators (B) are on the side shown.
Loosen the indicated Adjustment Handle (47),
and insert the Saddle Post (3) into the Frame (2).
Move the Saddle Post upward or downward
to the desired position, and then tighten the
Adjustment Handle. When you are finished
tightening the Adjustment Handle, make sure
that the end of the Adjustment Handle is
pointing upward.
Note: The Adjustment Handle (47) functions
like a ratchet. Turn the Adjustment Handle in
the desired direction, pull it outward, turn it in
the opposite direction, push it inward, and then
turn it in the desired direction again. Repeat this
process as many times as necessary.
4Grease

8
5
5. Note: You can attach your own saddle to the
Saddle Carriage (4) if desired. Loosen the
attachment hardware (not shown) beneath the
Saddle (5), and remove the Saddle. Then, attach
your own saddle and retighten the attachment
hardware.
Orient the Saddle Carriage (4) as shown.
Loosen the Adjustment Handle (47), and slide
the Saddle Carriage (4) into the Saddle Post (3).
Slide the Saddle Carriage to the desired posi-
tion, and tighten the Adjustment Handle.
Then, attach an M4 Washer (54) and the
Carriage Cover (91) to the Saddle Carriage (4)
with an M4 x 14mm Screw (117).
3
4
5
117 47
54
91
6
6
2
68
105
47
C
C
E
D
6. See step 8. If the Handlebar Clamp (28) and
four M6 x 16mm Screws (110) are preattached
to the Handlebar Carriage (105), remove them
and set them aside until step 8.
Have a second person hold the Handlebar Post
(6) near the Frame (2).
Locate the long wire tie (C) in the Handlebar
Post (6). Tie the lower end of the long wire tie
to the Main Wire (68). Next, locate the same
wire tie in the access hole (E) in the Handlebar
Carriage (105). Pull the wire tie upward (D) until
the end of the Main Wire is in the access hole.
See the inset drawing. Next, pull the upper end
of the long wire tie (C) until the Main Wire (68) is
routed through the Handlebar Carriage (105) as
shown. Then, untie and discard the long wire tie.
Tip: Avoid pinching the Main Wire (68).
Loosen the indicated Adjustment Handle (47),
and insert the Handlebar Post (6) into the
Frame (2). Move the Handlebar Post upward or
downward to the desired position, and tighten
the Adjustment Handle.
Avoid pinching the
Main Wire (68)
105
68 C

9
7. Have a second person hold the Handlebar (7)
near the Handlebar Carriage (105).
Locate one of the remaining wire ties (F) in the
Handlebar Carriage (105). Tie the indicated end
of the wire tie to the Right Extension Wire (107).
Then, pull the other end of the wire tie until
the Right Extension Wire is routed through the
Handlebar Carriage. Then, untie and discard the
wire tie.
Route the Left Extension Wire (108) through
the Handlebar Carriage (105) in the same
way.
8. Tip: Avoid pinching the wires. Hold the
Handlebar (7) on the Handlebar Carriage (105),
and rotate the Handlebar to the desired angle;
make sure that the Handlebar is centered on
the Handlebar Carriage.
Attach the Handlebar (7) with the Handlebar
Clamp (28) and four M6 x 16mm Screws (110);
start all the Screws, and then tighten them.
7
8
7
7
110
28
105
105
108
107
F
F
Avoid pinching
the wires

10
105
107, 108
9
9
9
68
9. Have a second person hold the Console (9) near
the Handlebar Carriage (105).
Connect the console wires to the Main Wire (68)
and to the Extension Wires (107, 108); make
sure to connect the console wire that has an
“L” tag to the Extension Wire that has an “L”
tag, and connect the console wire that has an
“R” tag to the Extension Wire that has an “R”
tag.
Insert the excess wire into the Console (9).
10
111
105
10. Tip: Avoid pinching the wires. Attach the
Console (9) to the Handlebar Carriage (105)
with four M4 x 12mm Screws (111); start all the
Screws, and then tighten them.
Avoid pinching
the wires
11. Attach the Tray (8) to the Frame (2) with two
M4 x 10mm Screws (116). 11
8
2
116