PROAIM Cinema Series Comet User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
Comet 12 Euro Cinema Jib (JB-COMT)
Assembly Manua l
Proaim 7 Comet Jib
1 x 3 Extension Arm
2 x Counterweight Rods
1 x 3 Extension Rod
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
NOTE: If you have purchased (JB-COMT-01) kit, you will receive the following:

2
 Insert Levelling Support Feet on all 4 corners
of Ridgeline Dolly. Secure them with a ring.
 Insert Lever onto Levelling Support to adjust
the length of feet from ground. Then lock
the Support with knob.
 Apply the Front Wheel Brakes while
assembling to ensure double security. Insert
Steering Push/Pull Bar into Dolly’s Rear-axle.
Ridgeline Dolly Setup
 Fix screw into the Steering and lock from
both sides to secure Steering accurately.
NOTE: To avoid unwanted accident while assembling the crane, please assemble the dolly with
supporng feet. It also increases the stability.
Ridgeline Dolly With
4 x Levelling Support Feet
Centre Column
NOTE: If you have purchased (JB-COMT-02) kit, you will also receive the following:

3
 Place lower secon of Centre Column onto
the Dolly. Twist the Column to align all its
corners with screws. Tighten them back to
secure it.
Aaching the Centre Column
 Place Centre Column onto the centre of
dolly. Insert & ghten screws on all corners
to secure the Column.
 Place Comet Jib onto the Euro-adapter of
Centre Column.
 Fix the Jib fork with Centre Column by
locking the knob via locking lever.
 Lock both the pan knob to assemble the jib
crane.
Jib Crane Setup

4
 Loosen knob on top located on the back
(operator) side of jib. Then take out the side
knob.
 Insert Counterweight Rod through the holes
and lock the knob on top. Then add weights
(Not Included) to both the Rods as per the
requirement and secure them with Locking
Pin.
 Loosen the knob on Adjustment
Counterweight and slide it to ensure right
balance of jib, as shown in image.
 Loosen side knob on the front (camera) side
of jib and the red buon knob on Rod, to
remove the camera mounng secon.
 Now loosen boom knob on the front
(camera) side of jib and press the small red
buon on side to release (pull-out) the
Telescopic Secon.
 Pull out the Telescopic Secon from back
(operator) side of jib. Insert the side knob
again to lock it.

5
 Then press the laer small red buon on
steel Rod to release (pull-out) the Telescopic
Secon of Rod.
 Then aach Extension Rod of 3 with
Telescopic Secon of Rod and lock with the
red buon knob appropriately to secure it.
 Now insert camera mounng secon into
the Extension Arm and Rod.
 Tighten side knob of jib and red buon knob
on Rod to lock the mounng secon
accurately.
 Aach 3 Extension Arm with Telescopic
Secon and lock the knob appropriately to
secure it.
NOTE: You can precisely balance the
plaorm with its unique Levelling
Mechanism on Rod.
 Finally, mount your camera setup as desired,
on Double Euro Adapter provided with the
mounng secon of jib.

6
 7.3 Jib Length– When jib length is 7.3 Jib will be balance with 12.5kg weight, with every 2kg
of camera setup you need to add 4.5kg weight to balance it. Now total weight 12.5 + 4.5kg= 17kg.
 9.1 Jib Length– When jib length is 9.1 Jib will be balance with 21.5kg weight, with every 2kg
of camera setup you need to add 4.5kg weight to balance it. Now total weight 21.5 + 4.5kg= 26kg.
 12.5 Jib Length– When jib length is 12.5 Jib will be balance with 38.5kg weight, with every
2kg of camera setup you need to add 6.5kg weight to balance it. Now total weight
38.5 + 6.5kg= 45kg.
NOTE: Use Micro balance for Precission balancing.
Balancing Tips

7
YOUR PROAIM COMET CAMERA JIB CRANE
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.