PROAIM Fly 22 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Fly 22’ Crane with LW-100 Stand (P-FLY-22-S)
Assembly Manua l
LW-100 Jib Stand Spreader
2X Red Cables
2X Blue Cables
Weight Rod
Secon 1A
Secon 2B
Secon 3C
Secon 4D
Secon 5E

2
Weight Closer Weight Safety Ends Connecvity Plate
Cable Guide Support Rods
Packing
Safety Hints
ATTENTION: PLEASE READ THIS BEFORE USING TO PREVENT DAMAGE TO EQUIPMENT
& OPERATOR!
 The crane may not be assembled or operated under the inuence of alcohol, drugs or any other intoxi-
cang substances. Lack of aenon while connecng the components can cause substanal damage
to equipment/operator.
 The crane may only be operated on levelled horizontal posion. Make sure that the surface is stable.
 To prevent any harm or injury, properly join all secons of the crane. It is suggested to use the support
stand while telescoping the complete length.
 Do not exceed the maximum payload capacity of the Tripod. Do not adjust the tripod leg locks or move
the Tripod or remove the ground spreader while the crane is aached to the Tripod.
 Always connect the steel cables properly to provide stability to the system. They should not negavely
impact the movements of the crane in any way.
 Aer setup of the crane, the pan-lt head / gimbal head shall be posioned under the central pivot
secon. In the assembled state, when the pan-lt head / gimbal head is higher than the central pivot
secon, there should be someone to look aer the crane system.
 The complete panning & liing range around it must be kept free. Avoid anybody standing under the
crane. No loose objects may be stored or placed on it. Be very careful while using it indoors.
 Never operate the crane near high-voltage power cables. It holds danger to life.
 Parcular care is required when operang the crane in unfavourable weather condions. The crane
must be shut down in sucient me. When it is used on a rainy day, the pan-lt head / gimbal head
and controlling bar shall be protected against rain.
 When you want to transport the crane, lock the Pan & Tilt Axis for safety. Make sure that the
components do not rub together and cause any material wear.

3
 Take out the Spreader from Accessory Bag.
Spread the spreader on oor and open the
legs of spreader with help of provided knob.
Jib Stand Setup
 Open the legs of 100mm jib stand then aach
it to spreader, lock it in place with the rubber
grips.
 Now mount central fork onto tripod , then
aach boom clamp to secure it well.
Jib Secons Setup
 Slide the (1A Secon) into central fork
(secon 2B) and ghten with help of knob. Slide
 Before the counterweights are removed, ensure the remote head is resng on the support stand.
Then gradually remove the counterweights before the remote head, camera or other parts.
 In the interest of safe crane operaon, avoid abruptly swivelling or stopping the crane; otherwise, it
may cause severe damage to equipment.
FOLLOWING THESE GUIDELINES WILL PROVIDE BETTER SHOTS AND TROUBLE-FREE OPERATION.
SHOULD YOU NEED ADDITIONAL INFORMATION, TECHNICAL ASSISTANCE IS AVAILABLE ‘ONLINE’ BY
CONTACTING THE SALES REPRESENTATIVE.

4
 Insert connecng bars (secon 1A) aached
it with both the ends (weight bar & secon
2B) the both ends using the provided knob.
 Using the same approach insert 3rd, 4th and
remaining secons to joints and secure via
knobs as shown.
 Aach short cable guide rod on 3rd secon
properly. Insert knob onto the cable guide
rod and ghten the knob properly.
Cable Guide & Support Rod Setup
 Loosen the bolts on cable guide rod in order
to aach cable guide support rod to it.
Reghten the bolt.
 Using the same steps to and aach long
cable guide rod on 2nd secon as shown.
 Insert weight rod on (1 secon) and ghten
the bolt with help of allen key as shown in
the picture.
Connecon Bar
Knob

5
 Then insert safety ends at both sides onto
the weight rod.
Cable Code (Red)
Stability Cables Setup
 Aach (Red) cable to (2B secon) & (secon
3C) & align it properly with help of cable
guide clamp and aached with (5E secon).
 Aach cables and insert the hook onto the
weight rod.
 Align it to the cable guide side rod and aach
it to the end (secon 5th).
NOTE: You can adjust the cable with help of
wire tensioner.
 Now aach both red cable hook onto the
provided bolts properly as shown.
Cable Code (Blue)
NOTE: Both the red cables are following same steps.