John Thomas TV-27 User manual

ITEM NO.: TV-27
REVISED JAN 09, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: MISSION CORNER TV STAND
: TV-27

ITEM NO.: TV-27
REVISED JAN 09, 2016
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts
from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
-Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of
your product. Protect the surface of the product with cloth if you are using any product with
rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-27
REVISED JAN 09, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
F
Shelf
1
B
Side frame
(L-R)
2
G
Drawer
side (L-R)
2
C
Supporting
bar
1
H
Drawer
front
1
D
Bottom
panel
1
I
Drawer
bottom
1
E
Back
panel
1
J
Drawer
back
1
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qt
y
Sketch
1
Bolt
(M6x35mm)
8
6
Flat washer
(6.5x19mm)
8
2
Long screw
(M4x35mm)
2
7
Bracket
4
3
Allen key
(M4x80mm)
1
8
Pan head screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
1
4
Short screw
(M3x15mm)
7
9
Medium screw
(M4x30mm)
8
5
Spring washer
(6.5x13mm)
8
10
Wooden nob
(38x30mm)
1
METAL KNOB
(30x30mm)
GOES WITH
FINISHED ITEM
ONLY.
1

ITEM NO.: TV-27
REVISED JAN 09, 2016
Printed in Vietnam
- 4 -
STEP 1
Attach bottom panel (D) to side frames (B) with bolts (1) and washers (5) and (6) as shown below.
Tighten with Allen key (3).
Attach supporting bar (C) to side frames (B) with screws (2) as shown below. Tighten with a
screwdriver.
STEP 2
Slide back panel (E) into grooves of side frames (B) as shown below.

ITEM NO.: TV-27
REVISED JAN 09, 2016
Printed in Vietnam
- 5 -
STEP 3
Attach top (A) to side frames (B) with bolts (1) and washers (5) and (6) as shown below. Tighten with Allen
key (3).
STEP 4
Attach brackets (7) to side frames (B) as shown below. Then place shelf (F) on the brackets and attach
with screws (4). Tighten with a screwdriver.

ITEM NO.: TV-27
REVISED JAN 09, 2016
Printed in Vietnam
- 6 -
STEP 5
Attach back panel (E) to the unit with screws (4). Tighten with a screwdriver.
STEP 6
Attach drawer sides (G) to drawer front (H) with screws (9) as shown below. Tighten with a screwdriver.

ITEM NO.: TV-27
REVISED JAN 09, 2016
Printed in Vietnam
- 7 -
STEP 7
Slide drawer bottom (I) into grooves of drawer sides (G) and drawer front (H) as shown below.
STEP 8
Attach the drawer back (J) to the drawer sides (G) with screws (9) as shown below. Tighten with a
screwdriver.

ITEM NO.: TV-27
REVISED JAN 09, 2016
Printed in Vietnam
- 8 -
STEP 9
Attach knob (10) to front of drawer with pan head screw (8) as shown below. Tighten with a screwdriver.
STEP 10
Carefully put the drawer (from step 9) into the unit.