Argos Hudson 331/8218 User manual

Hudson - Table
331/8218
Assembly Instructions - Please keep for future reference
Issue 1 - 10/10/14
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 183cm
Depth - 92cm
Height - 76cm

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
1Top panel (183 x 92cm)
3Cross rail (94 x 9.2cm)
4Support rail x 2 (88 x 9.2cm)
2Leg x 2 (82 x 70cm)

A
B
3
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
C
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(small & medium)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
2m
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 03456 400 800
50mm Bolt x 10 Allen key x 1
140mm Bolt x 4

Assembly Instructions
4
Step 1
Step 2
Fixing cross rail.
Important:
Two people are
required for an easier
assembly.
Fix legs into the pre
drilled holes in the cross
rail using bolts and
allen key .
Fixing rail.
Fix support rail into the
pre drilled holes in the leg
using bolts and
allen key .
Repeat step 1 for the
other leg and support rail.
2B
2
C
2
4
B
B
2x
B
C
4
4
C
3
A
A
2x
A
C
3
2
2
A

Assembly Instructions
5
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Step 3
Step 4
With help, after fixing top
panel, carefully stand the
product upright.
Assembly is complete.
Fixing top panel.
Important:
Two people are
required for an easier
assembly.
Caution:
Carefully lay the
top panel on a soft and
clean surface to avoid
damaging the product.
Fix legs into the pre
drilled holes in the top
panel using bolts
and allen key .
Do not overtighten bolts
.
2
1B
C
1
2
2
B
B
B
B
B
B
6x
C
B
B

Hudson - Cross Leg Bench
356/4828
Assembly Instructions - Please keep for future reference
Issue 1 - 10/10/14
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 170cm
Depth - 35cm
Height - 45cm

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
1Seat panel (170 x 35cm)
2Cross rail (140 x 6.5cm)
4Support rail (55 x 4.5cm)
3Leg x 2 (42.5 x 33.8cm)
5Vertical frame x 2 (18 x 6.5cm)

E
A
C
3
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
D
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(small & medium)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
2m
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 03456 400 800
40mm Screw x 7
Allen key x 1
B
70mm Bolt x 2 100mm Bolt x 4
60mm Bolt x 4