PROLiNK INSPIRE 703SFC User manual

Version 1.00
(English | Indonesian)
User Guide
Fast
Line interactive UPS
with Super
charging speed
INSPIRE 703SFC, INSPIRE 853SFCU,
INSPIRE 1203SFCU, INSPIRE 1253SFCU,
INSPIRE 1503SFCU, INSPIRE 2003SFCU,
INSPIRE 3003SFCU

CAUTION:
8.
9.
10.
11.
12.
13.
14.
i.
ii.
iii.
iv.
v.
Remove watches, rings, or other metal objects.
Use tools with insulated handles.
Wear rubber gloves and boots.
Do not lay tools or metal parts on top of batteries.
Disconnect charging source prior to connecting or disconnecting batteries terminal.
WARNING:
1. DO NOT modify the UPS input cable.
2. Consult your dealer if the UPS input cable connector does not match the utility receptacle.
3. The UPS must be grounded while in use. Operate the UPS only from a properly grounded AC outlet
(2 wire plus ground).
4. Turn off the UPS before unplugging it from the AC outlet.
Important Safety Warning1
EN1
To prevent the risk of fire or electric shock, install in a temperature and humidity controlled
indoor area free of conductive contaminants. (See the specifications for the acceptable
temperature and humidity range.)
To reduce the risk of overheating the UPS, DO NOT cover the UPS' cooling vents and
avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances
such as space heaters or furnaces.
DO NOT attach non-computer-related items, such as medical equipment, life-support
equipment, microwave ovens, or vacuum cleaners to UPS.
DO NOT plug the UPS input into its own output.
DO NOT allow liquids or any foreign object to enter the UPS. DO NOT place beverages or
any other liquid-containing vessels on or near the unit.
In the event of an emergency, press the OFF button and disconnect the power cord from
the AC power supply to properly disable the UPS.
DO NOT attach a power strip or surge suppressor to the UPS.
Attention hazardous through electric shock. Also with disconnection of this unit from the
mains, hazardous voltage still may be accessible through supply from battery. The battery
supply should be therefore disconnected in the plus and minus pole at the quick connectors
of the battery when maintenance or service work inside the UPS is necessary.
Servicing of batteries should be performed or supervised by personnel knowledgeable of
batteries and the required precautions. Keep unauthorized personnel away from batteries.
When replacing the batteries, use the same number and type of batteries.
Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery.
DO NOT dispose of batteries in a fire. The battery may explode. DO NOT open or mutilate
the battery or batteries. Released electrolyte is harmful to the skin and eyes.
Unplug the UPS prior to cleaning and DO NOT use liquid or spray detergent.
A battery can present a risk of electric shock and high short circuit current. The following
precaution should be observed before replacing batteries:
1.
2.
3.
4.
5.
6.
7.

Package Contents2
EN2
x 1 x 1
Note:
1. The illustrations in this document may appear different from your model.
2. If any of above item is not packed in your package when open, please consult your seller immediately.
Overview3
Battery Mode Indicator:
Yellow LED Flashing
3
INSPIRE 703SFC
Front View Rear View
6
5
2
3
4
1
Legend:
Backup Outlets
6
Power AC Input
5
Fault Indicator:
Red LED Lighting
2
AC Mode Indicator:
Green LED Lighting
4
Power Switch
1
English

Overview3
EN3
INSPIRE 853SFCU
7
5
Front View Rear View
8
6
2
3
4
1
Legend:
USB Port
5
RJ11 Ports (In & Out)
7
Backup Outlets
8
Power AC Input
6
Fault Indicator:
Red LED Lighting
2
Battery Mode Indicator:
Yellow LED Flashing
3
AC Mode Indicator:
Green LED Lighting
4
Power Switch
1
INSPIRE 1203SFCU
6
7
Front View Rear View
8
5
2
3
4
1
Legend:
Power AC Input
5
USB Port
6
RJ45 Ports (In & Out)
7
Backup Outlets
8
Fault Indicator:
Red LED Lighting
2
Battery Mode Indicator:
Yellow LED Flashing
3
AC Mode Indicator:
Green LED Lighting
4
Power Switch
1

Overview3
EN4
INSPIRE 1503SFCU
7
8
Front View Rear View
9
6
5
2
3
4
1
Legend:
Fan
5
USB Port
7
RJ45 Ports (In & Out)
8
Power AC Input
6
Backup Outlets
9
Fault Indicator:
Red LED Lighting
2
Battery Mode Indicator:
Yellow LED Flashing
3
AC Mode Indicator:
Green LED Lighting
4
Power Switch
1
INSPIRE 1253SFCU
6
7
Front View Rear View
8
5
2
3
4
1
Legend:
Power AC Input
5
RJ45 Ports (In & Out)
7
Backup Outlets
8
USB Port
6
Fault Indicator:
Red LED Lighting
2
Battery Mode Indicator:
Yellow LED Flashing
3
AC Mode Indicator:
Green LED Lighting
4
Power Switch
1
English

Overview3
EN5
INSPIRE 2003SFCU
7
8
Front View Rear View
9
6
5
2
3
4
1
Legend:
Fan
5
USB Port
7
RJ45 Ports (In & Out)
8
Power AC Input
6
Backup Outlets
9
Fault Indicator:
Red LED Lighting
2
Battery Mode Indicator:
Yellow LED Flashing
3
AC Mode Indicator:
Green LED Lighting
4
Power Switch
1
INSPIRE 3003SFCU
Legend:
Modem/Phone/
Network surge protection
5
AC input
7
USB port
8
Circuit breaker
6
Backup Outlets
9
Fault Indicator:
Red LED Lighting
2
AC Mode Indicator:
Green LED Lighting
Battary Mode Indicator:
Green LED Flasing
3
Power switch 4
AC Mode:
Indicating load level
Battery Mode: Indicating
battery capacity
1
Front View Rear View
9
5
3
4
1
2
4
7
6
8

EN6
Data Line Surge Protection (Only for the model with RJ11/RJ45)
Connect a single network/telephone/fax line into surge-protected “IN” outlet on the back
panel of the UPS unit. Connect from “OUT” outlet with another network/telephone/fax line
cable.
Turn On/Off the Unit
Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing again
the power switch.
Connect Communication Cable (Only for the model with USB port)
To allow for unattended UPS shutdown/start-up and status monitoring, connect the
communication cable one end to the USB port and the other to the communication port of
your PC. With the monitoring software installed, you can schedule UPS shutdown/start-up
and monitor UPS status through PC.
CAUTION:
NEVER connect a laser printer or scanner to the UPS unit. This may cause the damage of the unit.
Connect the Loads
Plug in the loads to output receptacles on the rear panel of the
UPS. Simply turn on the power switch of UPS unit, and then
devices connected to the UPS will be protected by UPS unit.
English

EN7
Software Download & Installation5
Storage and Maintenance6
Note:
Only for model with USB port.
Please follow steps below to download and install monitoring software:
1. Go to the website http://www.power-software-download.com
2. Click ViewPower software icon and then choose your required OS to download the
software.
3. Follow the on-screen instruction to install the software.
4. When your computer restarts, the monitoring software will appear as orange plug icon
located in the system tray, near the clock.
5. For UPS with HID-compliant USB Port (optional), you may safely shutdown the UPS during
power failure simply by connecting to a computer with pre-installed Windows/ Linux/ Mac
OS through the USB port even without monitoring software.
Storage
Before storing, charge the UPS at least 6~8 hours. Store the UPS covered and upright in a
cool, dry location. During storage, recharge the battery in accordance with the following table:
Maintenance
-25°C - 40°C Every 3 months 1-2 hours
40°C - 40°C Every 2 months 1-2 hours
STORAGE
TEMPERATURE
RECHARGE
FREQUENCY
CHARGING
DURATION
The UPS system operates with hazardous voltages. Repairs may be carried out only
by qualified maintenance personnel.
Only persons are adequately familiar with batteries and with the required
precautionary measures may replace batteries and supervise operations.
Unauthorized persons must be kept well away from the batteries.
Batteries may cause electric shock and have a high short-circuit current. Please
remove all wristwatches, rings and other metal personal objects before maintenance
or repair, and only use tools with insulated grips and handles for maintaining or
repairing.
Even after the unit is disconnected from the mains, components inside the UPS system
are still connected to the battery packs which are potentially dangerous.

EN8
Troubleshooting7
Use the table below to solve minor problems.
No LED display on
the front panel
Alarm continuously
sounds when the
main is normal
When power
fails, back-up
time is
shortening
The main is normal
but LED is flashing Power cord is loose Reconnect the power cord properly
The UPS is overload
Battery defect. It might
be due to high
temperature operation
environment or improper
operation to battery
Replace the battery with the same
type of battery
Remove some critical load
Battery voltage is too low Charge the UPS at least 6 hours
The UPS is overload
Remove some loads first. Before
reconnecting equipment, please verify
that the load matches the UPS
capability specified in the specs.
Low battery Charge the UPS at least 6 hours
Battery fault
The UPS is not turned on Press the power switch again to turn on
the UPS
Replace the battery with the same type
of battery
PROBLEM POSSIBLE CAUSE SOLUTIONS
When replace the batteries, install the same number and same type of batteries.
Do not attempt to dispose of batteries by burning them. This could cause battery
explosion. The batteries must be rightly deposed according to local regulation.
Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin
and eyes. It may be toxic.
Do not disassemble the UPS system.
Storage and Maintenance6
English

EN9
Note: #1: Only applicable for INSPIRE 853SFCU.
Specifications8
MODEL INSPIRE 703SFC INSPIRE 853SFCU
Capacity
INPUT
650 VA 850 VA
OUTPUT
Voltage Range
Frequency
Phase
140 - 300VAC ±5% for 230VAC mode
140 - 290VAC ±5% for 220VAC mode
50Hz/60Hz (Auto-sensing)
Single + GND
Voltage Range
Battery Mode
Frequency
Waveform
Transfer Time
220VAC/230VAC + 12%-14%
220VAC/230VAC ±10%
50Hz ± 1% (Battery Mode); 60Hz ± 1% (Battery Mode)
Simulated Sine Wave (Battery Mode), Sine Wave (AC Mode)
2ms typical
Noise Level
Temperature
Humidity
Built in AVR
Diamension D x W x H
Weight (kg)
< 40dB
0˚C - 40˚C
0 - 90%
TRUE Full AVR (3steps)
279 x 101 x 142mm
BATTERY
PROTECTION/MONITORING
SOFTWARE MONITORING
Type & Number
Backup Time
Charging Time
12 V/ 7 AH x 1 12 V/ 9 AH x 1
8 - 30 mins depending on the load
2 - 4 hours recover to 90% capacity
Short Circuit
Protection
Surge
Protection
Alarm
UPS Protection
Overload
Protection
Intelligent Battery
Management
Data Line Surge
Protection
USB Connector #1
Software #1
AC Fault, Battery Low, Shutdown UPS
Support Windows® 7/ 8/ 10, Linux and Mac
GENERAL
RJ11-
4.2 4.9
Yes (Line Mode and Battery Mode)
Yes
Audible & Visual
Load Auto Sensing and Abnormal Protection
Line Mode - 100 - 120% 5mins change to fault mode
>120% change to fault mode immediately
Battery Mode - 100 - 120% 5 secs shutdown
>120% shutdown immediately
Prevent overcharging of battery
Protect battery and prolong battery life

EN10
Specifications8
MODEL INSPIRE 1203SFCU INSPIRE 1253SFCU
Capacity
INPUT
1200 VA 1250 VA
OUTPUT
Voltage Range
Frequency
Phase
140 - 300VAC ±5% for 230VAC mode
140 - 290VAC ±5% for 220VAC mode
50Hz/60Hz (Auto-sensing)
Single + GND
Voltage Range
Battery Mode
Frequency
Waveform
Transfer Time
50Hz ± 1% (Battery Mode); 60Hz ± 1% (Battery Mode)
Simulated Sine Wave (Battery Mode), Sine Wave (AC Mode)
2ms typical
220VAC/230VAC + 12%-14%
220VAC/230VAC ±10%
230VAC + 12%-14%
230VAC ±10%
Noise Level
Temperature
Humidity
Built in AVR
Diamension D x W x H
Weight (kg)
< 40dB
0˚C - 40˚C
0 - 90%
TRUE Full AVR (3steps)
320 x 130 x 182mm
BATTERY
PROTECTION/MONITORING
SOFTWARE MONITORING
Type & Number
Backup Time
Charging Time
12 V/ 7 AH x 2
8 - 30 mins depending on the load
2 - 4 hours recover to 90% capacity
Short Circuit
Protection
Surge
Protection
Alarm
UPS Protection
Overload
Protection
Intelligent Battery
Management
Data Line Surge
Protection
USB Connector
Software
AC Fault, Battery Low, Shutdown UPS
Support Windows® 7/ 8/ 10, Linux and Mac
GENERAL
RJ45
8.2 9.2
Yes (Line Mode and Battery Mode)
Yes
Audible & Visual
Load Auto Sensing and Abnormal Protection
Line Mode - 100 - 120% 5mins change to fault mode
>120% change to fault mode immediately
Battery Mode - 100 - 120% 5 secs shutdown
>120% shutdown immediately
Prevent overcharging of battery
Protect battery and prolong battery life
English

EN11
Specifications8
MODEL INSPIRE 1503SFCU INSPIRE 2003SFCU INSPIRE 3003SFCU
Capacity
INPUT
1500 VA 2000 VA 3000 VA
Voltage Range
Frequency
Phase
162 - 300VAC ±5% for
220/230/240VAC mode
Noise Level
Temperature
Humidity
Built in AVR
Diamension D x W x H
Weight (kg)
0˚C - 40˚C
0 - 90%
TRUE Full AVR (3steps)
PROTECTION/MONITORING
SOFTWARE MONITORING
Short Circuit
Protection
Surge
Protection
Alarm
UPS Protection
Overload
Protection
Intelligent Battery
Management
Data Line Surge
Protection
USB Connector
Software
AC Fault, Battery Low, Shutdown UPS
GENERAL
RJ45
320 x 130 x 182
10.4 10.6 14
Yes (Line Mode and Battery Mode)
Yes
Audible & Visual
Load Auto Sensing and Abnormal Protection
Line Mode - 100 - 120% 5mins change to fault mode
>120% change to fault mode immediately
Battery Mode - 100 - 120% 5 secs shutdown
>120% shutdown immediately
Prevent overcharging of battery
Protect battery and prolong battery life
OUTPUT
Voltage Range
Battery Mode
Frequency
Waveform
Transfer Time
50Hz ± 1% (Battery Mode); 60Hz ± 1% (Battery Mode)
Simulated Sine Wave (Battery Mode), Sine Wave (AC Mode)
BATTERY
Type & Number
Backup Time
Charging Time
12 V/ 9 AH x 2
Up to 40 mins depending on the load
2 - 4 hours recover to 90%
capacity 4 - 6 hours recover to 90% capacity
220VAC/230VAC + 12%-14%
220VAC/230VAC ±10%
220VAC/230/240VAC ±15%
220VAC/230/240VAC ±10%
50Hz/60Hz (Auto-sensing)
Single + GND
60Hz/50Hz (Auto-sensing)
Single + GND
2ms typical 2 - 6ms typical
140 - 300VAC ±5% for 230VAC mode
140 - 290VAC ±5% for 220VAC mode
< 45dB< 40dB
397 x 146 x 205
Support Windows® 7/ 8/ 10, Linux and Mac

PERINGATAN:
1. JANGAN memodifikasi kabel listrik yang masuk ke UPS
2. Hubungi dealer Anda jika konektor kabel tidak sesuai dengan konektor pada UPS
3. UPS harus terhubung pada ground saat sedang digunakan. UPS harus di hubungkan pada stopkontak AC yang
memiliki ground yang benar (2 kawat di tambah ground).
4. Matikan UPS sebelum mencabut dari stopkontak AC.
Peringatan Penting Keselamatan1
ID1
PERHATIAN:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
i.
ii.
iii.
iv.
v.
Lepaskan jam tangan, cincin, atau benda logam lainnya.
Gunakan alat yang terisolasi.
Pakailah sarung tangan dan sepatu bot dari bahan karet.
Jangan meletakan peralatan atau logam diatas baterai.
Cabut kabel yang terhubung langsung ke sumber listrik sebelum menyambung/mencabut
kabel terminal pada baterai.
Untuk mencegah resiko kebakaran atau sengatan listrik, pasang pada daerah yang suhu
dan kelembabannya terkontrol (Lihat spesifikasi untuk rentang suhu dan kelembaban
yang ditentukan.)
Untuk mengurangi resiko overheating dari UPS, JANGAN menutup ventilasi UPS dan
menempatkan pada daerah yang terkena sinar matahari langsung atau menempatkan
dekat dengan peralatan yang memancarkan panas.
JANGAN menghubungkan perangkat yang tidak berhubungan dengan computer, seperti
peralatan medis, oven microwave, atau vacuum pembersih pada UPS.
JANGAN menyambung input UPS ke output UPS itu sendiri.
JANGAN biarkan cairan atau benda asing masuk kedalam UPS. JANGAN menempatkan
minuman atau cairan dekat dengan unit.
Dalam keadaan darurat, tekan tombol OFF dan cabut kabel power dari sumber listrik untuk
memastikan UPS benar benar dalam kondisi tidak aktif.
JANGAN menambatkan power strip/surge pada UPS.
Perhatian tersengat listrik sangat berbahaya. Juga dengan melepaskan unit ini dari sumber
listrik, tegangan berbahaya masih tersimpan pada baterai. Kabel baterai juga harus
dilepas disaat melakukan perawatan atau perbaikan UPS jika diperlukan.
Perbaikan pada baterai harus dilakukan oleh personil yang memiliki pengetahuan tentang
baterai dan tindakan pencegahan jika diperlukan. Jauhkan dari personil yang tidak
mengerti.
Ketika mengganti baterai, gunakan jumlah dan jenis baterai yang sama.
Tegangan baterai internal adalah 12VDC. Sealed, lead-acid, baterai 6-cell.
JANGAN membuang baterai kedalam api. Baterai dapat meledak. JANGAN membuka
atau merusa baterai. Elektrolit yang terlepas berbahaya bagi kulit dan mata.
Cabut UPS sebelum melakukan pembersihan dan JANGAN gunakan deterjen cair atau
spray.
Baterai dapat menimbulkan resiko sengatan listrik dan hubungan singkat. Perhatikan
beberapa pencegahan berikut sebelum mengganti baterai:
Indonesian

Isi Perangkat2
ID2
x 1 x 1
Catatan:
1. Ilustrasi dalam dokumen dokumen ini mungkin tampak berbeda dari model anda.
2. Jika salah satu item di atas tidak dikemas dalam paket anda ketika terbuka, silakan berkonsultasi
dengan reseller anda segera.
Keterangan3
INSPIRE 703SFC
Tampak Depan Tampak Belakang
6
5
2
3
4
1
Keterangan:
Backup Outlets
6
Daya AC input
5
Indikator Fault: Lampu
penerangan Merah LED
2
Indikator Modus Baterai:
LED Kuning berkedip
3
Indikator AC Mode: Lampu
penerangan Hijau LED
4
Switch Daya
1

Keterangan3
INSPIRE 853SFCU
7
5
8
6
2
3
4
1
INSPIRE 1203SFCU
6
7
Tampak Depan Tampak Belakang
8
5
2
3
4
1
ID3
Tampak Depan Tampak Belakang
Keterangan:
Port USB
5
Port RJ11 (In & Out)
7
Backup Outlets
8
Daya AC input
6
Indikator Fault: Lampu
penerangan Merah LED
2
Indikator Modus Baterai:
LED Kuning berkedip
3
Indikator AC Mode: Lampu
penerangan Hijau LED
4
Switch Daya
1
Keterangan:
Daya AC Input
5
Port RJ45 (In & Out)
7
Backup Outlets
8
Port USB
6
Indikator Fault: Lampu
penerangan Merah LED
2
Indikator Modus Baterai:
LED Kuning berkedip
3
Indikator AC Mode: Lampu
penerangan Hijau LED
4
Switch Daya
1
Indonesian

Keterangan3
INSPIRE 1503SFCU
7
8
Tampak Depan Tampak Belakang
9
6
5
2
3
4
1
Keterangan:
Kipas
5
Port USB
7
Port RJ45 (In & Out)
8
Daya AC input
6
Backup Outlets
9
Indikator Fault: Lampu
penerangan Merah LED
2
Indikator Modus Baterai:
LED Kuning berkedip
3
Indikator AC Mode: Lampu
penerangan Hijau LED
4
Switch Daya
1
INSPIRE 1253SFCU
6
7
Tampak Depan Tampak Belakang
8
5
2
3
4
1
Keterangan:
Daya AC Input
5
Port RJ45 (In & Out)
7
Backup Outlets
8
Port USB
6
Indikator Fault: Lampu
penerangan Merah LED
2
Indikator Modus Baterai:
LED Kuning berkedip
3
Indikator AC Mode: Lampu
penerangan Hijau LED
4
Switch Daya
1
ID4

Keterangan3
ID5
INSPIRE 2003SFCU
7
8
Tampak Hadapan Tampak Belakang
9
6
5
2
3
4
1
Keterangan:
Kipas
5
Port USB
7
Port RJ45 (In & Out)
8
Daya AC input
6
Backup Outlets
9
Indikator Fault: Lampu
penerangan Merah LED
2
Indikator Modus Baterai:
LED Kuning berkedip
3
Indikator AC Mode: Lampu
penerangan Hijau LED
4
Switch Daya
1
INSPIRE 3003SFCU
Keterangan:
Modem/Phone/
Network surge protection
5
masukan AC
7
Port USB
8
Pemutus arus
6
Outlet Cadangan
9
Indikator Kesalahan:
Pencahayaan LED Merah
2
Indikator Mode AC:
Pencahayaan LED Hijau
Indikator Mode Baterai:
Ledakan LED Hijau
3
Saklar daya
4
Mode AC:
Menunjukkan tingkat beban
Modus Baterai: Menunjukkan
kapasitas baterai
1
Tampak Hadapan Tampak Belakang
9
5
3
4
1
2
4
7
6
8
Indonesian

ID67
PERHATIAN:
JANGAN menghubungkan printer lase atau scanner ke UPS. Hal ini akan menyebabkan kerusakan unit.
Perlindungan Lonjakan Jalur Data (Hanya untuk model dengan RJ11/RJ45)
Hubungkan satu saluran jaringan/telepon/faks ke stopkontak “IN” yang dilindungi lonjakan
arus di bagian belakang panel unit UPS. Terhubung dari outlet “OUT” dengan jaringan/
telepon/faks lain kabel.

Unduh Perangkat Lunak dan Instalasi5
Catatan:
Hanya untuk model dengan port USB.
Silakan ikuti langkah-langkah di bawah ini untuk mengunduh dan menginstal perangkat
lunak monitoring:
1. Pergi ke situs http://www.power-software-download.com
2. Klik ikon perangkat lunak ViewPower dan kemudian memilih OS yang dibutuhkan untuk
men-download perangkat lunak.
3. Ikuti petunjuk pada layar untuk menginstal perangkat lunak.
4. Ketika restart komputer anda, software monitoring akan muncul sebagai ikon plug jeruk
yang terletak di baki sistem, dekat jam.
5. Untuk UPS dengan Port USB yang sesuai dengan HID (opsional), Anda dapat mematikan
UPS dengan aman selama kegagalan daya hanya dengan menghubungkan ke komputer
dengan OS Windows/ Linux/ Mac yang sudah diinstal sebelumnya port USB bahkan
tanpa software monitoring.
Penyimpanan dan Pemeliharaan6
Penyimpanan
Sebelum menyimpan, isi daya UPS setidaknya 6~8 jam. Simpan UPS dalam keadaan tertutup
dan tegak di lokasi sejuk dan kering. Selama penyimpanan, isi ulang baterai sesuai dengan
tabel berikut:
Pemeliharaan
-25°C - 40°C Setiap 3 bulan sekali 1-2 jam
40°C - 40°C Setiap 2 bulan sekali 1-2 jam
SUHU
PENYIMPANAN
ISI ULANG
FREKUENSI
PENGISIAN
DURASI
Sistem UPS beroperasi dengan voltase berbahaya. Perbaikan hanya dapat dilakukan
oleh personel pemeliharaan yang berkualifikasi.
Hanya orang yang cukup akrab dengan baterai dan dengan yang diperlukan tindakan
pencegahan dapat mengganti baterai dan mengawasi operasi. Orang yang tidak
berwenang harus dijauhkan dari baterai.
Baterai dapat menyebabkan sengatan listrik dan memiliki arus hubung singkat yang
tinggi. Silahkan lepaskan semua jam tangan, cincin, dan benda pribadi logam lainnya
sebelum perawatan atau perbaiki, dan hanya gunakan alat dengan pegangan dan
pegangan berinsulasi untuk memelihara atau memperbaiki.
Bahkan setelah unit terputus dari listrik, komponen di dalam sistem UPS
masih terhubung ke paket baterai yang berpotensi berbahaya.
ID7
Indonesian

ID8
Permasalahan7
Gunakan tabel di bawah ini untuk menyelesaikan masalah kecil.
Tidak ada LED
yang menyala
pada panel
depan
Alarm secara terus
menerus berbunyi
ketika sumber listrik
normal
Ketika sumber
listrik terputus,
waktu back-up
sangat pendek
Listrik normal
tetapi LED berkedip Kabel power longgar Hubungkan kembali kabel power dengan
benar
UPS overload
Baterai rusak. Mungkin
disebabkan karena suhu
ruangan yang tinggi, atau
operasi yang tidak layak
pada baterai
Ganti baterai dengan jenis yang sama
Lepaskan beberapa beban critical
Tegangan baterai sangat
rendah Charge UPS minimal 6 jam
UPS overload
Lepaskan beberapa beban yang terhubung
ke UPS. Sebelum dipasang kembali, harap
pastikan beban masih dapat diterima oleh
UPS yang sesuai pada spesifikas
Baterai lemah Charge UPS minimal 6 jam
Baterai rusak
UPS belum dihidupkan Tekan saklar daya dengan jenis yang
sama
Ganti baterai dengan jenis yang sama
MASALAH KEMUNGKINAN SOLUSI
Saat mengganti baterai, pasang nomor dan jenis baterai yang sama.
Jangan mencoba membuang baterai dengan membakarnya. Ini dapat menyebabkan
baterai ledakan. Baterai harus dibuang dengan benar sesuai dengan peraturan setempat.
Jangan membuka atau merusak baterai. Keluarnya elektrolit dapat menyebabkan
cedera pada kulit dan mata. Ini mungkin beracun.
Jangan membongkar sistem UPS.
Penyimpanan dan Pemeliharaan6