Proluxe TACO BELL Vantage SL Compact User manual

Operations Manual
Vantage SL Compact - Compact Split Lid Grill
Model #: SL1266TB
WWW.PROLUXE.COM
Version: 022822

Congratulations on your selection of
the Vantage SL Compact Split Lid
Grill. Proluxe is a leading
manufacturer of food preparation
and cooking equipment designed for
the most demanding commercial
kitchens. Proluxe equipment is a
result of the highest quality
engineering and time-tested design.
This manual includes installation,
operation, and maintenance
procedures for your new split lid
grill. Please read this manual
carefully and keep it with your
machine for proper operation and
lasting service.
G E T T I N G S T A R T E D
Please read carefully before attempting to
use this appliance.
1. Place in location where it will be used
allowing for clearances per the
dimensions indicated. Allow 2”
minimum clearance between
adjacent equipment and/or wall
areas.
2. Plug into proper 3 prong wall outlet.
If other appliances are connected to
the same circuit make sure the total
load does not exceed a maximum
ampacity of the circuit. Electrical
information is as follows:
Electrical:
●Voltage: 120/230
●Amps: 15.83/8.3
●Hertz: 50/60
●Watts: 1900/1900
PLUG
●120V: 72” cord and NEMA 6-20P
approved plug.
●230V: 72” cord and plug per country
requirements.
3. Press the power button, the green
light above will illuminate when
powered on.The display flashes and
shows left preset timer during
warm-up. Pre-heat time will be 40-50
minutes. When the set point is
reached, the display stops flashing
and beeps 3 times.
4. Simply place product on either side of
the grill, close lid and press the
desired pre-set time cycle 10 or 20
seconds. After the time cycle is
finished press it again to reset the
time cycle.
1

I N T E R N A T I O N A L S Y M B O L S
Power Off
Power On
Hot Surface
Risk of Electrical Shock
Protective Earth Terminal
Caution - Warning
S A F E T Y S U M M A R Y
Warning
To reduce the risk of electrical shock, do not
remove or open cover. No user-serviceable
parts inside. Refer servicing to qualified
personnel.
In case of power cord damage, do not
attempt to repair or replace the power cord.
Please contact the manufacturer or the local
distributor.
Warning
For continued protection against fire and
electric shock, replace with the same type
and rating fuse. Listed Supplemental Fuse
rated max 3A, 120Vac.
Caution Hot
Avoid touching hot surfaces while operating
the machine.
Caution
When servicing or cleaning the machine,
make sure that the power cord is removed
from the wall socket.
During normal operation, the base of the
machine must be installed or placed above
the wall socket.
2

T E M P E R A T U R E/T I M E R
S E T T I N G S
How to Find Set Temperature
To find the temperature of upper platens:
Press and hold the TEMP button and the
arrow up (↑) button at the same time.
To find the temperature of bottom platens:
Press and hold the TEMP button and the
arrow down (↓) button at the same time.
Adjusting the Set Temperature
1. Press and hold the TEMP button and
the arrow up (↑) button at the same
time for 15 seconds.
2. The current temperature with display
on the right digital display screen
only.
3. Using the up (↑) and down (↓) adjust
the temperature to your desired
setting.
4. Once your desired temperature is set,
push the TEMP button to return.
Adjusting the Set Time
1. Press the TEMP button first and then
select the desired timer button and
hold for 5 seconds.
2. The current temperature with display
on the right digital display screen
only.
3. Using the up (↑) and down (↓) adjust
the timer to your desired setting.
4. Once your desired temperature is set,
push the TEMP button to return.
Note: When adjusting the timer settings, the
right set of buttons control the left side. Your
left side timer will automatically set to your
right control settings. If you desire a separate
left timer you can manually adjust the left
side timer without affecting the right timer.
3

C L E A N C Y C L E
Start Cycle
To start a clean cycle, push CLEAN button
once so the CLEAN LED light is turned on. All
preset LED’s are turned off, and the
temperature set point is changed to the clean
set point of 275°F. This also initiates the cool
down to clean set point condition as well the
display starts flashing until the clean set
point is reached.
Stop Cycle
To stop the clean cycle, simply press the
CLEAN button once to deactivate the clean
cycle. The CLEAN LED is turned off, the
preset LED’s are restored, the temperature
set point is changed to the main set point.
Again, the warm-up condition is initiated and
the display flashes until the cook set point is
reached.
Change Clean Temp
275°F is the factory default temp for the
CLEAN cycle. To change the CLEAN cycle
temp, simultaneously hold down the TEMP
and CLEAN buttons for 15 seconds. The
current temp setting will display on the right
digital display only. Using the up or down
arrows to adjust to the desired temp.
P R E V E N T A T I V E
M A I N T E N A N C E
Proluxe machines are relatively maintenance
free. For a long lifespan, the following
preventative maintenance should be
followed:
Daily Care:
1. Platens: Turn your machine off and allow
to cool down before attempting to clean.
These platens should only be cleaned with
mild soap and warm water then wiped off
with a clean, soft cloth or soft sponge.
2. Exterior surfaces: Wipe daily with mild
soap and warm water.
DO NOT use ice or cold water to cool the
unit down. This can cause platens to warp.
Service Problems:
Contact our factory at [phone] (U.S.
only) or approved service agency. When
contacting the factory for information, parts
or service instructions, please provide the
serial number of the machine be provided.
This number can be found on the serial plate
located on the rear of the machine.
4

Vantage SL Compact Troubleshoot Guide - Model #: SL1266TB
Problem
Cause
Action
Ref #
Power Button on
Digital Controller
face is depressed but
doesn’t turn on.
1. Power cord is not plugged in.
2. Circuit breaker is tripped off in the
site's breaker box.
3. Transformer has taken an
electrical surge and is damaged.
4. Check voltage on the secondary
side of the Transformer. If you read
12VDC then you are receiving
voltage to the controller.
5. Possible blown fuse.
1. Plug the power cord into wall
receptacle and power button.
2. Reset circuit breaker that the
grill is plugged into. Depress
Power Button to turn on.
3. Replace Transformer after you
check secondary side of
transformer. If working properly,
you should receive 12vdc.
4. Replace controller. Controller
should be on once the power
button is depressed.
5. Replace fuse.
77
-----
39
31
32
Digital Controller's
LED's are scrambled
or randomly erratic.
If when turning on,
the display will first
go to segment check
1. Possibly a component on the
Digital controller is damaged.
2. Control needs to reset.
1. Replace digital controller.
2. While unit is on unplug unit,
wait for 1 min. Then plug machine
on again and depress the power
button.
-----
31
Digital Controller on
startup goes through
LED segment check
(8888) then to
version # and then
loops back to to the
above reboot.
The relay driver on the digital control
may be blown.
Replace digital controller.
31
Digital display shows
PROB. No heat on
any platen.
Sensor lost it's continuity as shown
on a muti-meter.
Disconnect prob that is open (no
continuity as shown on a multi-
meter. Must replace sensor
(RTD). Do not cut and splice new
sensor. Install new 2000 ohm
RTD sensor to under side of heat
platen and reconnect to the
controller.
37,
38
5

When depressing the
tactile button on
digital controller,
nothing happens.
The tactile buttons under the overlay
may be not close enough to activate.
Same goes if the buttons are already
pressed by overlay without
depressing button.
Carefully (no too much at one
time to avoid fracturing the
traces on the controller) tighten
the nuts on the back of the
controller until button activate.
Same goes in reverse if buttons
are held down by the overlay.
Digital display shows
relay and particular
zone is overheating.
Beeper not
functioning or
intermittent beeper
sound.
1. The relay on the switched side is
not opening to regulate temperature.
2. Beeper on digital control board
failed.
1. Replace the relay.
2. Replace digital controller board
27
31
If setpoint is reached
but slightly off in
temperature.
Offset may need to be calibrated and
adjusted.
Call [phone] ext. 129 for
instructions.
Heater platen
overheating
If the relay (depending on the year of
the model) on the coil side are
receiving 12vdc indicates the
controller is functioning properly. On
the switching side of the relay, is
there 120 vac going to the heater in
question. If there is no voltage on
the to the switching side of the relay
to the heaters, the relay is not
working properly.
Replace relay If the controller's
heat-on LED is not lit indicating
the controller is working
properly.
27
6

7

8

9

Vantage SL Compact Part List - Model #: SL1266TB
ITEM #
DESCRIPTION
SL1266TBA - 120V
QTY.
1
UPPER PLATEN, INSULATION
11018344074C1
2
2
LOWER PLATEN, INSULATION
11018344019
1
3
HANDLE SPRING ADJUSTING COLLAR
110115528
2
4
SPRING TORSION LH
1101023154L
1
5
SPRING TORSION RH
1101023154R
1
6
BASE FRAME ASSEMBLY
11018344038
1
7
LOWER PLATEN INSULATION COVER
11018344018
1
8
COVER, BOTTOM ASSY
11018344022
1
9
TUBING-PAD
110115531
2
10
SHROUD, LEFT ASSY
11018344044
1
11
SHROUD, RIGHT ASSY FOR SPATULA HOLDER
PG17804
1
12
CAM COLLAR
110115530
2
13
SHIM, SHROUD COVER
11018344014
2
14
SHIM, LOWER PLATEN
11018344030
1
15
STOP, HEX PIN
11018344037
2
16
LEVELING BRACKET
11018344023
2
17
COVER, REAR
11018344016
1
18
PLUNGER ASSEMBLY
110115544
2
19
CLEVIS ASSY LEFT HAND
11018344013
1
20
CLEVIS ASSY RIGHT HAND
11018344012
1
21
HANDLE LEFT ASSEMBLY
11018344027
1
22
HANDLE RIGHT ASSEMBLY
11018344026
1
23
GREASE TRAY ASSY
11018344005
1
24
PIN, PIVOT FRONT
11017088865
2
25
TOP LINK
11018344017
2
26
SPACER, LINK
11018344024
2
27
SINK, HEAT, ALUMINUM (SSR)
11057322
3
28
WIRE HARNESS
11018344050
1
29
OVERLAY SL1266, TACO BELL
OSL1266TBB
1
30
TRANSFORMER INSULATION
1101159180
1
31
DIGITAL CONTROL 3 ZONE SOFTWARE REV 5.54
1101041052
1
32
FUSE BUSS 1 AMP
MPPF701R
1
10

33
MARKER STRIP #4 DOUBLE
MS6014
2
34
FUSE HOLDER 1 AMP
MPPF708
1
35
TERMINAL BLOCK #4, DOUBLE
6014
2
ITEM #
DESCRIPTION
SL1266TBA - 120V
QTY.
36
SOLID STATE RELAY, 25 AMPS
PL2425
3
37
2000 OHM RTD, BOTTOM SENSOR
1108881102
1
38
RTD TOP SENSOR 45.5"
1108881101
2
39
TRANSFORMER
11096975
1
40
STRAIN RELIEF
1106546468
1
41
WASHER, SAE #8
WSAE8
6
42
WASHER, LOCK INTERNAL TOOTH 5/16"
WLIT516
4
43
WASHER, LOCK 1/4
WL14
2
44
WASHER, INTERNAL TOOTH LOCK #8
WLIT8
3
45
WASHER, CUT 5/16
WC516
6
46
WASHER, INTERNAL TOOTH LOCK #6
WLIT6
6
47
WASHER, 5/16" SPLIT LOCK
WL516
10
48
WASHER, SAE 3/8"
WSAE38
12
49
WASHER, LOCK 3/8
WL38
4
50
WASHER, .311 OD X .150 ID X .20 THK
311150019
6
51
WASHER, HI-TEMP COMPRESS, NON-ASBESTOS
C4401
2
52
SCREW, PAN HEAD PHILLIPS 8-32X 3/8 SS
SP83238S
16
53
SCREW, SET 3/8-16 X 1-1/2
SST3816112
4
54
SCREW, SET 3/8-16 X 1/2
SST381612
5
55
SCREW, PHILLIPS PAN 2-56x1/4
SP25614
1
56
SCREW, PAN HEAD PHILLIPS 8-32 X 1/2
SP83212
10
57
SCREW, PHILLIPS PAN HEAD 8-32 X 1/4
SP83214
2
58
SCREW, PAN HEAD 8-32 X 1
SP8321
1
59
SCREW, SET 5/16-18 X 3/8 KNURLED POINT
SST5161838KN
12
60
SCREW, SET 3/8-16 X 1
SST38161
2
61
BOLT, SOCKET HD 5/16-18X3/4"
SSH5161834
6
62
BOLT, 5/16 -18 x 1 SS HEX HEAD
BH516181S
4
63
BOLT, HEX 1/4-20X1
BH14201
2
64
NUT, HEX 6-32
NH632
6
65
NUT, HEX 1/4-20
NH1420
2
66
NUT, HEX 3/8-16
NH3816
4
11

67
NUT, HEX 8-32
NH832
3
68
BUSHING, TEFLON, 3/4" ID X 7/8" OD X 1" L
110115541
4
ITEM #
DESCRIPTION
SL1266TBA - 120V
QTY.
69
BUSHING, FLANGED TEFLON 3/4 ID X .875 OD X .5 L
110115563
4
70
BUSHING TEFLON 3/4" ID X 7/8" OD X 3/4" L
110113441
2
71
SPRING, DETENT
110115555
2
72
LOW CLEARANCE CLIP
LCC3478
4
73
NYLON SPACER 1/4 X .141 X 9/32
11090109
6
74
HANDLE GRIP
110901168
2
75
FEET, RUBBER 3/4
11016546469
4
76
RETAINING RING
11017088867
8
77
POWER CORD, 30 AMPS
1101591174
1
78
PIN, LEVELER, REAR
11018344048
2
79
SPATULA HOLDER
PG17803
1
80
SL1266 MANUAL, TACO BELL
MSL1266TBA
1
A1
UPPER PLATEN WITH WIRING LEFT SIDE
11018344074120LK
1
A2
UPPER PLATEN WITH WIRING RIGHT SIDE
11018344074120RK
1
A3
UPPER PLATEN LEFT SIDE ASSY
11018344075120LAK
1
A4
UPPER PLATEN RIGHT SIDE ASSY
11018344075120RAK
1
A5
LOWER PLATEN WITH WIRING
11018344032120K
1
A6
LOWER PLATEN ASSY
11018344032120AK
1
A7
CONTROLLER TEMPERATURE ASSEMBLY
11018344035K
1
12

13

Warranty & Return Policy
Proluxe warrants all products manufactured
by it against defects in workmanship or
materials from the date of purchase for a
period of 1 year on parts and labor. This
warranty applies to only equipment
purchased and used in the United States.
Warranty period shall begin when equipment
ships. Warranty travel will only be covered
for 60 miles.
ALL WARRANTY SERVICE CALLS MUST BE
APPROVED BY PROLUXE. IF THIS
PROCEDURE IS NOT FOLLOWED,
WARRANTY SERVICE WILL NOT BE
COVERED. WARRANTY SERVICE WILL BE
PAID ON STRAIGHT TIME, OVERTIME WILL
NOT BE COVERED.
Service Calls
Contact our factory to obtain warranty
service. Proluxe must issue a return
authorization number, and call tag, or find the
name and location of a Factory Authorized
Service Center nearest you. When calling for
service, please furnish the model number,
serial number, and a
description of the problem.
E X C L U S I O N S
The warranties provided by Proluxe DO NOT
apply to the following:
●Damage due to misuse, abuse,
alteration, or accident.
●Improper or unauthorized repairs.
●Submerged in water.
●Damaged in shipment.
●Equipment exported to foreign
countries.
Special Order Equipment and
Accessories
Cannot be canceled and are not returnable
unless defective within the terms of this
warranty.
In no event shall Proluxe be liable for
consequential damages arising out of the
failure of any of its products if operated
improperly or caused by normal wear or
damaged by operator abuse.
Limited Lifetime Warranty on
Heating Elements
If replacement is needed, Proluxe will send
the new part at no charge but labor will not
be covered unless the unit is still under the 1
year manufacturer warranty.
R E T U R N E D M E R C H A N D I S E
P O L I C Y
Should it become necessary to return any of
the company’s products, the following
instructions must be adhered to: First,
contact our customer service department for
approval and a return authorization number.
Please have the serial number of your item
available at that time. All merchandise must
be shipped freight prepaid by customer or
service agency. Subject to the inspection of
the product by the company, a restocking
charge of 20% of the Net purchased price
paid to Proluxe will be assessed.
14

Merchandise may not be returned for credit
without prior written approval of Proluxe.
Collect shipments will not be accepted. No
returns after 60 days of original shipment
date on machines. Purchased parts may not
be returned after 30 days. If upon inspection
by Proluxe or its authorized agent it is
determined the equipment has not been used
in an appropriate manner, has been modified,
or has not been properly maintained, or has
been subject to misuse, misapplication,
neglect, abuse, accident, unauthorized
modification, damage during transit, delivery,
fire, flood, act or war, riot or act of God, then
this warranty shall be deemed null and void.
T E R M S & C O N D I T I O N S
1. Price List prices are suggested retail prices
and are shown in U.S. Dollars.
2. Terms of Payment: 1% 10 days, NET 30
days.
3. New Accounts: Satisfactory credit
information must be provided before open
account status can be extended.
Unless agreed otherwise, all shipments will
be made C.O.D., Cash in advance.
4. Pricing: Prices, specifications, model
numbers, capacities and accessories are
subject to change without notice.
5. Freight/Routing: Method of shipment will
be determined by Proluxe unless otherwise
advised by purchaser.
6. Damaged Claims: All merchandise shipped
at purchaser’s risk. Inspection must be made
by purchaser at time goods are received. If
goods are damaged, the PURCHASER shall
request that the agent of the transportation
company make a written notation on the
proper shipping documents immediately and
then file a claim for damages.
Note: Goods damaged in shipping are
non-returnable.
7. Returns: Machines may not be returned
after 60 days. Purchased parts may not be
returned after 30 days. A restocking fee of
20% will be assessed on non-warranty
returns.
8. Taxes: Prices indicated herein DO NOT
include State, Federal, Local or foreign taxes
or duties, nor do they include fees, permits,
insurance or other levies, all of which are the
responsibility of the purchaser.
9. All orders are subject to acceptance by
Proluxe.
10. Possession of this price list shall not be
considered an offer to sell
15