ProMinent DULCOMARIN II DXM Series Wiring diagram

Part No. 986906 ProMinent Dosiertechnik GmbH ·69123 Heidelberg ·Germany BA DC 048 12/08 GB
Please carefully read these operating instructions before use! ·Do not discard!
The operator shall be liable for any damage caused by installation or operating errors!
ProMinent
®
Please enter the identcode of your module!
DXMa ___ ___ ___ ___ ___ ___
A-Module
Supplementary Instructions
DULCOMARIN®II, A Module
(Actuator Module, Pumps and
Standard Signal Outputs mA)
DXMaA
BA_DC_048_12_08_GB.p65 17.12.2008, 11:51 Uhr1

ProMinent®
Page 2
Imprint:
Supplementary Instructions
DULCOMARIN®II, A Module
(Actuator Module, Pumps and Standard Signal Outputs mA)
DXMaA
© ProMinent Dosiertechnik GmbH, 2004
ProMinent Dosiertechnik GmbH
Im Schuhmachergewann 5-11
69123 Heidelberg
Germany
Phone: [phone]
Fax: [phone]
[email protected]
www.prominent.com
Technical changes reserved.
Printed in Germany
Imprint
These operating resp. supplementary instructions apply only in conjunction
with the following ticked operating resp. supplementary instructions:
Operating Instructions Multi-Channel Measuring and Control System
DULCOMARIN
®
II Swimming Pool Controller and Disinfection Controller DXCa
Part 1: Mounting and Installation
Operating Instructions Multi-Channel Measuring and Control System
DULCOMARIN
®
II Swimming Pool Controller DXCa
Part 2: Operation
Operating Instructions Multi-Channel Measuring and Control System
DULCOMARIN
®
II Disinfection Controller DXCa
Part 2: Operation
Supplementary Instructions DULCOMARIN
®
II Videographic Recorder
Operation
Supplementary Instructions DULCOMARIN
®
II, M Module
(Measurement Module for pH, Redox/ORP, Temperature) DXMaM
Operation
Supplementary Instructions DULCOMARIN
®
II, M Module
(Measurement Module for pH, Redox/ORP, Temperature) DXMaM
Connection
Supplementary Instructions DULCOMARIN
®
II, A Module
(Actuator Module, Pumps and Standard Signal Outputs mA) DXMaA
Supplementary Instructions DULCOMARIN
®
II, N Module
(Power Supply Module without Relays) DXMaN
Supplementary Instructions DULCOMARIN
®
II, P Module
(Power Supply Module with Relays) DXMaP
Supplementary Instructions DULCOMARIN
®
II, I Module
(Current Input Module, Standard Signal Inputs mA) DXMaI
✓
✓
✓
BA_DC_048_12_08_GB.p65 17.12.2008, 11:52 Uhr2

ProMinent®Page 3
Page
Identcode ......................................................................................... 4
1About this Module ................................................................. 5
2Safety Chapter ....................................................................... 5
3Storage and Transport .......................................................... 5
4Mounting and Installation ..................................................... 5
5Technical Data ....................................................................... 6
6Terminal Assignment ............................................................ 6
7Terminal Connection Diagram ............................................. 7
Contents
BA_DC_048_12_08_GB.p65 17.12.2008, 11:52 Uhr3

ProMinent®
Page 4
Identcode
Identcode
The identcode describes the external modules for the DULCOMARIN®II, series DXM
Only the measurement module in the mounting type W “wall-mounted”is available with controls and different languages.
DXMa Internal modules for DULCOMARIN®II, series DXC
These modules can be ordered via the identcode of the DXC (see “Operating Instructions Multi-Channel Measuring and Control System
DULCOMARIN®II Swimming Pool Controller and Disinfection Controller DXCa, Part 1: Mounting and Installation”).
2) only with Version: 2, no operator control
DXMa Measurement module for DULCOMARIN®II, series DXM
Module:
AA-module, actuator module: 3 pump and 4 standard signal outputs mA
Type of mounting:
WWall mounting (IP 65)
HMounting rail (IP 20)
ERetrofit module (installation module for DXCa, IP 20)
Version:
2Without controls
3Without controls (only mounting type “E”and “H”)
Application:
0Standard
Language:
00 No controls 2)
Approval:
01 CE mark
DXMa A W 2 0 00 01
BA_DC_048_12_08_GB.p65 17.12.2008, 11:52 Uhr4

ProMinent®Page 5
About this Module / Safety Chapter / Storage and Transport / Mounting and Installation
1About this Module
The actuator module DXMaA provides to the DULCOMARIN®II with the control options for
3 dosing pumps via pulse frequency, e.g. to raise and lower the pH value or to dose
disinfectants.
The actuator module DXMaA is equipped with the following outputs:
•4 standard signal outputs 0/4…20 mA, user-programmable and scalable for the measuring
values of e.g. pH value, redox/ORP, concentration of free chlorine or total chlorine or
combined chlorine or temperature.
•3 frequency outputs for controlling dosing pumps, e.g. to raise and lower the pH value or to
dose disinfectants.
and the following inputs:
•3 digital inputs for evaluating the alarm relay of the dosing pumps and for monitoring of the
tank level.
2Safety Chapter
The actuator module DXMaA may only be used as component part of the DULCOMARIN®II.
The installation may only be performed by specially trained personnel!
3Storage and Transport
Only store and transport the module in its original packaging.
CAUTION
Also protect the packaged module against humidity and exposure to chemicals.
Environmental conditions for storage and transport:
Temperature: - 10 °C to 70 °C
Climate: Permissible relative humidity: 95%, non-condensing (DIN IEC 60068-2-30)
4Mounting and Installation
WARNING
•The installation may only be performed by specially trained personnel!
•Please carefully read the instructions in the “Operating Instructions Multi-Channel
Measuring and Control System DULCOMARIN®II Swimming Pool Controller and
Disinfection Controller DXCa, Part 1: Mounting and Installation” before carrying out any
mounting and installation work!
CAUTION
The standard signals can be distorted, which might have consequences for the process!
Only devices with own electrical isolation of the individual standard signal inputs (e.g.
standard signal inputs of a recorder, …) may be directly connected to the standard signal
outputs!
If a multi-channel standard signal input module of a PLC is to be connected to several
standard signal outputs of the DXMaA module, each standard signal line is to be routed via
a 3-way standard signal separator (a 3-way standard signal separator electrically isolates
the input, the output and the supply voltage).
In case of several standard signal lines, a multi-channel isolating amplifier can be used.
ProMinent recommends 4-channel isolating amplifiers of the type LC-TV-4I.4I of the
company of Rinck (www.rinck-electronic.de) or of the type 6185D of the company of PR
Electronics (www.prelectronics.de) to connect up to 4 standard signal lines.
NOTE
The terminal connection diagram is enclosed at the end of these supplementary
instructions.
Carry out the CAN connection as described in the “Operating Instructions Multi-Channel
Measuring and Control System DULCOMARIN®II Swimming Pool Controller and Disinfection
Controller DXCa, Part 1: Mounting and Installation”.
BA_DC_048_12_08_GB.p65 17.12.2008, 11:52 Uhr5

ProMinent®
Page 6
5Technical Data
Electrical data
Frequency outputs
(Opto-MOS relay)
for pump control
(R1, R2, R3): Contact type: make contact with series inductance, interference-suppressed
Load rating: 400 V peak, 250 mA switching current, max. 0.8 W
maximum frequency: 8.33 Hz (500 strokes/min.)
Close/open time: 5 ms
Digital inputs
(K1, K2, K3) (Kl. 9 – 14): galvanically isolated among each other
Insulation voltage: 500 V
max. switch frequency: 2 kHz
Connectable contacts: mechanical relays
max. connectable cable length: 20 m
Standard signal outputs mA
(I out 1 - I out 4): Insulation voltage: 500 V
Output range: 0/4-20 mA (programmable)
23 mA for error message
maximum load: 400 Ω
Accuracy: 0.5% of the output range
For the installation, Chap. 4 “Mounting and installation”must be observed!
Environmental conditions
Storage temperature: -10...70 °C
Type of protection IP 20 (within the housing DXM: IP 65)
Humidity: Permissible relative humidity: 95 %, non-condensing (DIN IEC 60068-2-30)
Materials
Housing: PPE-GF 10
6Terminal Assignment
Technical Data / Terminal Assignment
Description Terminal Terminal no. Pole Function
description
Frequency output 1 R 1 1+pH lowering pump (control)
2- pH raising pump
3+chlorine pump (control)
Frequency output 2 R 2 redox pump
4- acid pump
Frequency output 3 5+ flocculant pump
R 3 redox pump
6- chlorine pump
Digital input 1 K 1 7+ error pump
8-
Digital input 2 K 2 9+ error pump
10 -
Digital input 3 K 3 11 + error pump
12 -
Power output 0/4-20 mA 1 I out 1 13 + pH value
14 - control variable pH lowering
control variable pH raising
control variable chlorination
control variable flocculation
control variable redox/ORP
(recorder connection)
BA_DC_048_12_08_GB.p65 17.12.2008, 11:52 Uhr6

ProMinent®Page 7
Power output 0/4-20 mA 2 I out 2 15 + redox/ORP value
16 - control variable pH lowering
control variable pH raising
control variable chlorination
control variable flocculation
control variable redox/ORP
(recorder connection)
Power output 0/4-20 mA 3 I out 3 17 + chlorine value
18 - control variable pH lowering
control variable pH raising
control variable chlorination
control variable flocculation
control variable redox/ORP
(recorder connection)
Power output 0/4-20 mA 4 I out 4 19 + combined chlorine
20 - control variable pH lowering
control variable pH raising
control variable chlorination
control variable flocculation
control variable redox/ORP
(recorder connection)
Terminal Assignment / Terminal Connection Diagram
Description Terminal Terminal no. Pole Function
description
7Terminal Connection Diagram
Extra-low voltage
Relay outputs
Digital inputs
DXMaA
Internal
External
R1 R2 R3 K1 K2 K3
Standard signal outputs
0/4 - 20 mA
I out 1 I out 2 I out 4I out 3
BA_DC_048_12_08_GB.p65 17.12.2008, 11:52 Uhr7

ProMinent®
Page 8
Technical changes reserved.
ProMinent Dosiertechnik GmbH
Im Schuhmachergewann 5-11
69123 Heidelberg
Germany
Phone: [phone]
Fax: [phone]
[email protected]
www.prominent.com
BA_DC_048_12_08_GB.p65 17.12.2008, 11:52 Uhr8