Prostat CVM-780 User manual

User Manual
CVM-780
CONTACT VOLTMETER


  Page
I. Introducon 4
II. General Descripons 4
III. Theory of Operaon 6
IV. Notes & Cauons 6
V. Receiving & Instrument Setup 8
VI. Making Electrostac Voltage Measurements 13
VII. Performance Characteriscs & Consideraons 14
VIII. Capacitance & Accuracy 17
IX. Measuring Insulators 18
X. Recording Measurement from Analog Output 18
XI. Instrument Maintenance 19
XII. Warranty 20
General Specicaons 21

Copyright © 2011 by Prostat® Corporaon. All rights reserved. Printed in the United States of America. No part of this
manual may be used or reproduced in any manner whatsoever without wrien permission. For informaon contact
Prostat Corporaon, 1072 Tower Lane, Bensenville, IL 60106 USA
Prostat is the registered trademark of Prostat® Corporaon

4Rev. D / January 2015
CVM-780 Contact Voltmeter
I. 
The Prostat CVM-780 is a portable high impedance voltmeter with
an acve probe system used for locang and measuring electrostac
potenals on conductors and other materials. Its intended purpose
is to determine voltages on crical conductors such as devices and
assemblies in electronics industry manufacturing and test environ-
ments. It is indispensible for
• Analyzing the electronic manufacturing/test/repair process
to determine levels of protecon for ESD sensive devices
from Machine Model (MM) and Charge Device Model
(CDM) damage, and
• Locang cause(s) of ESD failures.
• Measuring voltages on devices, subassemblies, assembly equipment, xtures, automac test
xtures, tools, chassis, mobile equipment, dissipave materials, etc.
The CVM-780 Contact Voltmeter™ combines the ease of use of a digital voltmeter with the high input im-
pedance and low input capacitance of a true electrostac voltmeter in a small, portable, baery operated
package. The contact probe enables you to measure voltages with pinpoint accuracy. Ceramic Probe Tips
allow accurate measurement without signicant ESD or RF generaon. Robust metal ps are supplied for
general audit and equipment measurements.
Being a true electrostac voltmeter, not a eld meter means that the CVM-780 reads real voltage, without
confusing it with electrostac eld strength, which can be disnctly dierent. The CVM-780 uses a unique
acve probe design which is fully guarded and shielded for minimal interference with the surrounding E
eld. The CVM-780 is powered by rechargeable Nickel Metal Hydride baeries; a compact universal bat-
tery charger is supplied for internaonal use. Properly used, the CVM-780 Contact Voltmeter will become
one of your most valuable portable ESD Analysis tools.
II. 
The CVM-780 features a large easy to read LED display, analog output, and rechargeable baery in a shock
absorbent package, and a specially designed acve probe assembly.
A. The probe assembly is connected to the CVM-780 case using
a supplied 6-foot DB9 cable
B. Ceramic or metal probe ps are used to make direct contact
with objects and surfaces under test. Voltage is shared with
the probe assembly, the measurement is calculated, and
shown on the LED display

5
Rev. D / January 2015
CVM-780 Contact Voltmeter

Ceramic ps are fragile and used for direct contact with ESD sen-
sive devices and assemblies. Metal ps are robust and used to
measure equipment, xtures, tools and other non-ESD sensive
elements.
C. Connect the CVM-780 to a previously tested ground to provide a
dened reference for accurate measurements
D. CVM-780 intended measurement range is 0 - ±525 volts in
one volt increments. All measurements are immediately
shown in the 3 digit LED display. Polarity switching during
measurements is automac
E. The round brass front panel
ground plate is used as a
zero reference for the
instrument. Between
measurements the probe
p (ceramic or metal pin) is placed in contact with the ground
plate to conrm the probe p’s zero voltage as displayed on the
panel LED. Instrument zero is adjusted using the manual adjust-
ment provided below the LED display.
F. An analog output mini-jack receptacle is provided for monitoring or recording CVM-780 measure-
ments. The analog output jack provides an output of 0.1 millivolt for each 1.0 volt measured by
the CVM-780. The output is independent of the meter indicaon to maximize response me. The
output is compable with the Prostat® PGA-710 or PGA-710B Autoanalysis System™.
G. A universal AC/DC baery charger is provided for charging the AA sized Metal Hydride recharge-
able baeries. Baery life is approximately 3.5 hours. Fully charged baeries should provide a full
day of measurements if the unit is turned OFF when not in use.

6Rev. D / January 2015
CVM-780 Contact Voltmeter
H. A small p replacement tool is supplied to prevent probe and
p damage when exchanging ps. The p should never be over
ghtened
I. An outer removable rubber boot reduces mechanical shock
during portable operaons and provides an easel stand during
use.
J. few alcohol prep wipes are included to periodically clean the
black insulator mounted at the front of the probe assembly. The wipe may be used to clean the
probe and instrument cases.  the alcohol wipes on the display LED.
III. 
The CVM-780 operaon is quite unique.
A. As the probe p of the CVM-780 approaches a charged conductor it senses the conductor’s
charge. The p is driven by the probe to match the conductor’s polarity and increases p voltage
as its distance to the conductor decreases.
B. While p voltage connues to increase as it approaches the charged conductor, the CVM-780
probe p does not reach the conductor’s full voltage unl it physically contacts the charged con-
ductor.
C. At the moment of contact a small transfer of electrons occurs from the conductor to the CVM-780
p that completes the measurement. The probe p voltage will be well within
1. 5% of the conductor’s original voltage, ±2 counts from ±25 to ±525 volts, and
2. Within 10% ±2 counts at <±25 volt measurements.
Therefore the change in conductor voltage at moment of p contact is very small.
D. Though very small electron transfer occurs at moment of contact, there is no measureable “ESD”
event when employing ceramic ps. The small amount of electron transfer is controlled by both p
and probe design. Also, there is no signicant RF generated because the electron transfer is small
and “relavely slow” to avoid a discharge event.
E. The resulng measurement accuracy depends on the actual voltage of the conductor, the length
and types of probe ps, and the inuences in the measurement environment. Environmental
inuences include presence and movement of objects and bodies, ambient condions, and size of
objects and their distance to ground (Capacitance).
IV. 
The CVM-780 is a precision instrument designed to measure electrostac DC voltage.

7
Rev. D / January 2015
CVM-780 Contact Voltmeter
• Do not use the instrument or probe assembly for AC measurement applicaons
• Do not expose the instrument it to shock or excessive moisture.
• Use good measurement pracces at all mes.
Warranty is  if either the instrument case or probe assembly are opened or misused. There are no
user adjustments inside the instrument or probe assembly. Contact Prostat Corporaon for service, fur-
ther informaon and operaonal suggesons

Internal instrument and probe voltage can exceed ±575 volts.
  the instrument case or probe assembly as painful personal
shock may occur.
 into instrument connectors
  any unauthorized instrument, xture or device to the
CVM-780 instrument or probe assembly as permanent equipment damage
and, or an unsafe condion may occur.
  when
metal probe p is installed
 The CVM-780 probe assembly uses very sharp pin-like ceramic and metal ps for measure-
ments that will cause painful and possibly serious injury if not handled with care.
• Keep probe p covered with supplied probe p cover when not in actual use.
• Store reserve ps in supplied foam lined plasc accessories case
• DO NOT make contact to people with ceramic or metal pin ps; REMOVE pin ps when making
personnel measurements
The CVM-780 instrument is designed to measure electrostac voltage on objects; -

 The operator is grounded during normal operaons while holding the probe assembly. Do not
make contact with, or touch energized AC circuits with your free hand or the probe p assembly
This instrument is not intended for use in ammable or combusble environments
Ceramic and metal measurement ps are supplied with this instrument. Tips are costly to replace
and may be easily damaged. Handle them with care; store them in the supplied accessory box.
Lost or damaged ps can be replaced by con-
tacng your Authorized PROSTAT Reseller.
The CVM-780 must be connected to an approved ground for proper operaon and accurate mea-
surements
 The CVM-780 is powered by rechargeable metal hydride baeries. Dispose of depleted baeries in
a safe manner and in accordance with local laws and ordinance.
 DO NOT OPEN the instrument or probe assembly. There are no customer serviceable parts or ad-
justments inside the instrument package or probe assembly.
The CVM-780 has been in test and use for over 2 years prior to manufacture for general ESD applicaons.

8Rev. D / January 2015
CVM-780 Contact Voltmeter
It has proven itself reliable and quite stable. The customer should have few if any problems with this
unique instrument. If aer examining this manual and you have quesons, contact Prostat or its Autho-
rized Resellers for assistance. See the “Warranty” secon later in this document for detailed informaon
regarding further coverage and support.
Prostat Corporaon assumes no liability in the event of instrument misuse, ignoring above Notes, CAU-
TION’s and WARNING’s. Should the instrument be opened or serviced by unauthorized personnel or dam-
aged by misuse, all liability, repair, replacement and freight costs are the customer’s responsibility.
V. 
The CVM-780 meter assembly, probe and accessories set is shipped in foam lined shipping package and
includes the following items:
A. CVM-780 Meter Assembly with 4 each rechargeable Metal Hydride baeries (AA size) installed
during inial assembly and test.
B. Rubberized “boot” to enhance instrument protecon during mobile operaons, which incorpo-
rates an easel stand to assist viewing during measurements.
C. CVM-780 Probe assembly is an acve assembly equipped with precision electronics. Its sensing p
is protected by a removable p cover.
D. Probe/Meter DB-9 style cable connects the meter assembly and acve probe
E. Universal baery charger for recharging installed metal hydride baeries
B C D

9
Rev. D / January 2015
CVM-780 Contact Voltmeter
F. Accessories box containing
1. 2 Metal probe ps, approximately 0.9 and 0.4 inches
2. 2 Ceramic probe ps, approximately 0.9 and 0.4 inches
3. Tip installaon and removal tool
G. Q007B ESD Grounding Cube for connecng to equipment ground in
North American facilies
H. PFP-861LL 72 Inch Green ground lead
I. Heavy duty bulldog clip supplied for connecon to ESD common point ground points
CVM-780 Contact Voltmeter
Probe Assembly
6 . DB-9 Connecon Cable
Q007B ESD
Grounding Cube
Universal Baery Charger
PFP-861LL 72 inch Green
Lead
Pin Set & Tool
G H I
Analog Connecon
Cable

10 Rev. D / January 2015
CVM-780 Contact Voltmeter
 
Low Ba Indicator
Manual Zero
LED
Display
Ground
Plate
J. Before using the CVM-780 fully charge the
metal hydride baeries using supplied universal
baery charger.
1. Plug charger into a standard AC outlet. Use
appropriate adapter if necessary.
2. Plug charger’s DC output connector rmly
into the CVM-780 charging receptacle locat-
ed in the side panel of the Meter assembly
3. Baery charging LED will be ORANGE during
charging and GREEN when charge is com-
pleted.
4. Disconnect the charger from AC when
charge is complete and for mobile operaons
K. Install a ceramic or metal probe measurement p at the front end of the probe assembly
1. Remove the p cover by PULLING it straight o the probe. Avoid twisng the cover during its
removal or installaon.
2. Select an appropriate p from the accessory box.
Probe Tips have very sharp points – handle them with care to avoid injury

11
Rev. D / January 2015
CVM-780 Contact Voltmeter
3. Ceramic ps are used for making direct contact with ESD sensive parts and assemblies during
precision measurements
CERAMIC TIPS ARE FRAGILE. They are brile, and should be handled carefully to avoid
damage. Tips are not covered by warranty and are costly to replace.
4. Metal ps are used for general audit and equipment measurements
5. Short ps (0.4 in) provide greater accuracy than long ps (0.9 in) – See Performance Character-
iscs for detailed informaon
6. Use the supplied p installaon and removal tool to install the selected p.
7. Simplify installaon by inserng the pin point into the installaon tool.
8. Place the threaded pin base into the front probe gold threaded receptacle
9. Screw the pin clockwise unl just nger ght and seated into the threaded receptacle.
DO NOT OVER TIGHTEN TIP DURING INSTALLATION. Excess torque may damage the
probe assembly or pin and cause diculty during p replacement.
10. The supplied p tool is used to install and loosen the p during replacement

12 Rev. D / January 2015
CVM-780 Contact Voltmeter
11. Always replace probe p cover to prevent damage to ps
and to avoid personal injury when
a. probe is not actually in use
b. during transport
c. While in storage.
L. Connect the Probe and Meter assemblies using the DB-9 cable
a. Carefully insert the 9 pin cable/meter connectors to the meter front end panel and to the
probe connecon box. Secure them in posion with the installed thumb screws. Do not
over ghten.
b. Insure the DB-9 cable is not twisted or kinked
 Avoid tangling or catching the cable on foreign or moving objects during use
M. Connect the CVM-780 to an earth ground
a. Insert the Green ground wire banana in the green Ground
receptacle located on the side panel of the Meter assem-
bly.
b. Connect the free end of the ground wire to ground using
the supplied grounding block or alligator clip
the CVM-780 must be connected to an approved ground
for proper operaon and accurate measurements
Avoid tangling or catching the ground wire on foreign
OR MOVING objects during use
 The operator is grounded during normal operaons while holding the probe assembly.
Do not make contact with, or touch energized circuits with your free hand or the probe p
assembly

13
Rev. D / January 2015
CVM-780 Contact Voltmeter
VI. 
The CVM-780 is designed to measure electrostac voltage on conductors without discharging the object
in queson. When using metal probe ps, a slight voltage dierenal during metal to metal contact will
cause low level ESD and RFI generaon. When using a ceramic probe p small ESD events and low level
RFI generaon are avoided. Use the following guidelines for making measurements on conductors. These
procedures assume the above receiving and setup steps above are completed, and all cauons and warn-
ings are followed.
1. Release the easel stand at the back of the unit and stand the
CVM in a semi vercal posion.
Place the instrument on a stable plaorm, or hand hold the
instrument with the easel retracted
2. Locate the power switch on the side panel and slide it toward
the meter’s front end to the ON posion.
a. The front panel LED display will illuminate
b. The instrument is energized for operaon
3. Remove the probe p cover by pulling it straight o. Do not twist the cover unnecessarily.
4. Place the probe p in direct contact with the round brass ground plate on the instrument’s
front panel
a. The LED should indicate 000
b. To adjust LED indicaon while the probe is grounded, turn the sloed Manual Zero knob
unl the LED indicates 000
Ground the p using this procedure between measurements

When the probe p is not in contact with ground or making a dened measurement,
the measurement system is “oang”. When oang free of a contact measurement any
indicated displayed voltage is normal and not meaningful. (See Instrument
Maintenance, below.)

14 Rev. D / January 2015
CVM-780 Contact Voltmeter
5. Once the probe is zeroed touch the p to the conducve ob-
ject being measured
a. Hold the probe steady with slight pressure on the p.
Avoid p damage, 

b. The voltage measurement will be seen on the front panel
LED display
c. Indicated voltage will stabilize quickly, usually within 2 to 5 seconds
d. Should changes in displayed voltage occur during measurement they are typically due to:
i. Natural ionizaon of the electrostac charge to air
ii. The eect of nearby ionizaon
iii. Capacive coupling with moving objects and personnel nearby
iv. Charging or Discharge of the conducve object being measured by means other than
the CVM-780 measurement
6. Ground probe p to the front panel ground plate
between measurements
7. Turn the CVM-780 power switch to OFF when instru-
ment is not in use, and replace probe p cover
8. If Low Ba LED on front panel illuminates, recharge
the unit’s baeries.  The CVM-780 may be
used for measurements during charging. However,
as baery voltage will be changing during the charge
be sure to ground and re-zero the probe p between
measurements.
VII. 
While CVM-780 measurements are easily performed, one should develop and pracce a consistent tech-
nique to make accurate measurements with the CVM-780. Grounding the instrument is important for
accurate results because “ground” is the instrument’s zero reference for its measurement circuit.
The CVM-780 probe is “acve”. Its internal components assess p voltage as it approaches a charged
conductor. It communicates with the instrument package to increase, and provide similar p voltage upon
contact with the conductor being measured. The front panel LED displays p voltage measurements upon
contact with an object or material.
Once the measurement is obtained, separaon from the conductor being measured does not reset the
probe to zero. In eect it remains at a similar voltage as the last measurement, or may “oat”. Grounding
the p between measurements resets the system to zero as can be seen of the front panel LED display.

15
Rev. D / January 2015
CVM-780 Contact Voltmeter

When the probe p is not in contact with ground or making a dened measurement, the
measurement system is “oang”. When oang free of a contact measurement any indi-
cated displayed voltage is not meaningful. (See Instrument Maintenance, below.)
Tip Selecon
Tip selecon is a maer of praccality, but will inuence measurement ac-
curacy. Typical measurement error is quite small regardless of p selecon:
≤ ±5%, ±2 Counts from ±25 to ±525 Volts
≤ ±10%, ±2 Counts from 0 to ± 25 Volts
However, performance accuracy will vary within these tolerances depending
on p material and p length. Comparave measurements indicate the fol-
lowing general guidelines for p performance.
Metal Tips Largest deviaon from reference Small ESD/RFI
Ceramic Tips Smallest deviaon from reference No ESD/RFI
Long Tips (0.9 – 1.3”) Largest deviaon from reference
Short Tips (0.4 – 0.6”) Smallest deviaon from reference
Consequently, the least accurate p is a long metal p; while the most accurate is a short ceramic p. In
all cases, accuracy will also vary based on technique, ambient condions, ground reference quality and
other variables discussed below.
Measurement Error
When measuring a constant, precision DC voltage reference, error is typically 1 volt or less, but always
equal to or less than ±2 volts. The circuit is capable of measuring the instrument’s enre voltage range, as
follows:
 
1A 500 V ≤ ±5 V
2A 100 V ≤ ±2 V
3A 50 V ≤ ±2 V
1B 10 V ≤ ±1 V
This procedure conrms the ability of the CVM-780 to measure DC voltage accurately, as would be ex-
pected of any good quality DC voltmeter. Variables within the error range are usually aributed to manual
zeroing of the instrument to ground. Indicaon of praccal measurement performance error in process
applicaons is a dierent maer and most important.
There are many variables in the manufacturing environment that will inuence measurement perfor-
mance of a contact voltmeter. To minimize those variables and esmate instrument measurement er-
ror, contact measurement of a charged precision 20 pF capacitor is made while the capacitor’s voltage is
monitored by a second high impedance contact voltmeter. The procedure creates a stable contact voltage
measurement situaon, as follows:

16 Rev. D / January 2015
CVM-780 Contact Voltmeter
1. A 20pF is placed on a ground plane and a high impedance contact voltage probe connected to
its charging conductor.
2. The capacitor is charged to a dened voltage using a precision DC voltage supply.
3. The CVM-780 under test is grounded and its probe zeroed.
4. The capacitor’s charged conductor is measured with the CVM-780 under test.
5. The CVM-780’s measurement deviaon from the (a) inial capacitor’s reference voltage before
contact by the CVM under test and (b) the installed voltage monitor aer test are recorded.
6. The data is then used to calculate the capacitor’s voltage change due to the measurement and
any deviaon seen between the installed reference instrument and the unit under test.
Typical measurement deviaon is summarized below.

 -



1C 450 - 525 V <±5% ±2 Counts ≤ ±2 Volts
2C 75 - 150 V <±5% ±2 Counts ≤ ±2 Volts
3C 40 - 65 V <±5% ±2 Counts ≤ ±2 Volts
4C <25 V <±10% ±2 Counts ≤ ±2 Volts
In the Performance Measurements table, above, the % DEV. FROM INITIAL CAPACITOR VOLTAGE is the to-
tal voltage change of the charged, monitored capacitor when the CVM under test makes contact with the
reference capacitor’s conductor. At the moment of contact by the CVM under test, the reference capacitor
system voltage changes slightly. The percent change from the capacitor’s inial voltage is based on a com-
binaon of two elements (a) the addional capacitance of the probe assembly p to that of the oang
capacitor and (b) some inevitable electron transfer between the capacitor conductor and the probe p.
The instrument monitoring the capacitor and the CVM-780 under test are both high impedance contact
voltmeters with very low capacive loading on the measurement. Consequently, if well zeroed and prop-
erly grounded they should each measure the same voltage on the capacitor aer contact of the CVM-780.
under test. Any error would be that of operator zero adjustment and ground anomalies. Thus a 2 volt or
less dierence between the two voltmeters would be considered acceptable.
Note that the precision reference capacitor is used to conrm CVM-780 performance by providing a stable
voltage plaorm. The use of charge plate monitors in CVM-780 performance tesng is avoided because
(a) while total CPM capacitance changes at the moment of probe contact, (b) total CPM capacitance var-
ies dramacally with its design and surroundings, including the operator and other moving objects in the
vicinity. Using a reference capacitor minimizes these measurement variables.
Thus, in real world the accuracy of praccal CVM-780 measurements of a conducve object are based on:
• The object’s capacitance and charge in combinaon with
• The probe assembly’s capacitance
• Ambient condions
• Process dynamics
• The small transfer of electrons between the probe p and the object under test

17
Rev. D / January 2015
CVM-780 Contact Voltmeter
Understanding these variables and the process condions heightens the value of the operator’s measure-
ments.
Metal Tips
Metal ps are far more robust than ceramic materials and less prone to damage. These ps are provided
for general audit and analysis measurements of equipment, chairs, carts, material handling items, tools,
xtures, etc. where many voltage measurements may be required, but close tolerance accuracy, minor
voltage discharge and low level RF generaon are not major factors. Metal ps should be used in these
applicaons to minimize use and potenal damage to ceramic ps.
Note that when using metal ps to measure conductors the slight dierenal voltage between the p
and the conductor at the moment of contact will result in some electron transfer. This, in turn, creates a
very small ESD event, and results in low level RFI signal being generated. These events are not harmful in
all but the most sensive environments, are dicult to see and usually not measureable in most applica-
ons. However, this is why metal ps are recommend for general audit measurements and ceramic ps
for ESD sensive device and assembly measurements.
Ceramic Tips
Ceramic ps provide the most accurate contact voltage measurements, and do so without causing a mea-
sureable ESD event or the resulng generaon of RFI. These materials are compounded and formed to
provide a controlled transfer of electrons upon contact with a conducve object. They are ideal for direct
contact measurement of ESD sensive devices and assemblies, or in areas and situaons where any ESD
or RFI may pose a problem.
Unfortunately, the ceramic ps are fragile, quite brile and can be easily damaged if one is not careful. In
addion, replacements are costly. When making general measurements use the metal ps and preserve
your expensive ceramic ps for crical device and assembly applicaons.
VIII. 
Actual accuracy is dependent on the user’s steady and reproducible technique, and environmental dy-
namics. In parcular, capacitance (C) of the item being measured relave to ground and other nearby
objects. This is based on
Q = CV
And,
Q = V
C
Where,
Q= Charge on the object
C= Capacitance of the item under test related to its size and distance to ground and other objects
V = Resulng voltage on object
Thus, any nearby movement of equipment components, personnel or objects may inuence the item
under test’s capacitance and subsequently its voltage. In a relavely non-dynamic environment measure-
ments are very accurate and stable. As a guideline, dene the measurement environment as the operator
and objects within 1 to 2 feet of the item being measured.
The eect of capacitance can be easily demonstrated. Apply voltage to the oang plate of a Charge Plate
Monitor (CPM). A standard six inch CPM will have a capacitance of approximately 20pF. While observing
the CPM’s plate voltage move your hand slowly back and forth near the surface of the oang plate. If

18 Rev. D / January 2015
CVM-780 Contact Voltmeter
you are grounded your capacitance will cause voltage measurement variance as your hand approaches,
and then leaves the CPM’s immediate vicinity. If you are ungrounded, your combined body charge, eld
and capacitance will have a signicant impact on the plate’s measurement. Repeat the measurement
while measuring the approximate voltage of the CPM oang plate with the CVM-780. You will see a simi-
lar shi in voltage as someone else’s hand approaches, and then leaves the vicinity of CPM’s surface.
The relaonship of Charge (Q), Capacitance (C) and Voltage (V) is the essence of electrostac measure-
ment and analysis. Prostat uses this relaonship to assess CVM-780 accuracy and performance.
 
Insulators are very dicult to measure accurately as almost every charge combinaon may be on the
material’s surface in immediate proximity to each other. When using a eld meter, one typically sees the
strongest eld polarity although both posive and negave charges may reside on the surface.
The CVM-780 is not designed to provide accurate and repeatable measurements of insulators. It will mea-
sure the voltage at the point of contact with an insulator. One might consider this an indicaon of voltage,
but not an exact material measurement. Unfortunately once the p makes contact and separates from the
surface aer the measurement, a new charge is triboelectrically generated at that point, and that spot’s
voltage will be changed. Thus, the measurement is only an approximate indicaon of surface voltage at a
point and is not repeatable.
 
The CVM-780 may be used to record indicated voltage with the PGA-710 and PGA-710B Autoanalysis
System™, or similar recording device. Be sure to zero both the CVM-780 and the recording device at the
same me.
When using the PGA-710 or PGA-710B, follow these steps:
A. Start the Autoanalysis Soware on your computer, connect the PGA-710 or PGA-710B and ener-
gize the operang system
B. In the Autoanalysis Soware:
1. Select the  dropdown menu
2. Open the window
C. Connect the supplied analog cable to the CVM-780 and PGA-710 or PGA-710B
D. Setup, ground and energize the CVM-780
E. Place the CVM probe assembly p against the front panel ground plate and adjust its approximate
zero point.
F. Click the Preview buon to start the graph display operaon.
G. Compare the CVM-780’s LED displayed voltage with the voltage displayed in the Current Measures
window of the Autoanalysis screen.

19
Rev. D / January 2015
CVM-780 Contact Voltmeter
1. If the PGA-710 or PGA-710B and CVM-780 zero seng are the same measurement recordings
can be made
2. If they are not the same, stop the Preview and proceed as follows.
H. Adjust the CVM-780 carefully to display 000 on its LED.
I. Select the Autoanalysis  drop down menu and open the  window. In the Volt-
age secon:
a. Click  buon, then
b. Click  buon, then
c. Click  buon to close the window and acve the zero reset
J. Start the Autoanalysis  and compare the  to the CVM-780’s LED
voltage; they should both be 000 ±1 volt.
As measured voltage increases, there is a small deviaon between CVM-780 displayed voltage and PGA-
710 or PGA-710B recorded voltage. It may be as low as ±2 volts below ±200 volts and increase to 5 or 6
volts deviaon at ±500 volts. The fact that the measurement can be made relavely accurately at that
level is signicant; the 5 to 6 volts deviaon is generally not an important error.
 
Maintenance ps and care of the CVM-780 follow.
A. There are no user adjustments or maintenance items inside the instrument case or probe assem-
bly. Do not open the case or probe as this will damage the instrument and VOID its warranty. War-
ranty seals are a reminder not to open these units.
B. Clean the surfaces of the instrument case and probe assembly with a low linng, non-abrasive
cloth lightly dampened with 70% soluon of alcohol and 30% water.
C. It is important to keep the front probe assembly black insulator very clean. Surface contaminants
on this insulator will cause voltage leakage to the probe’s grounded metal surface resulng in
unstable measurements. Use a low linng, non-abrasive cloth lightly dampened with 70% soluon
of alcohol and 30% water to clean the insulator. Alcohol prep wipes are useful for removing nger
oils and contaminants.
D. Excessive voltage dri while the probe is “oang” – that is, while not grounded or making a
contact measurement – may be caused by a large charge on the black insulator used for probe p
mounng. Insulator surface charge is caused by installing and removing the probe p cover. Exces-
sive “twisng” of the p cover increases this charge. This charge does not aect instrument ac-
curacy, but may become distracng. If desired remove this charge by exposing the probe assembly
to a balanced bench top ionizer. Note that the ionizer’s oset voltage (unbalance) will be displayed
on the CVM-780’s LED.

20 Rev. D / January 2015
CVM-780 Contact Voltmeter
E. Store the CVM-780 in a clean, dry environment with the p cover installed. For long term storage,
remove the Metal Hydride baeries.
F. Replacement Metal Hydride AA size rechargeable baeries are readily available in retail stores
and from electrical suppliers. Do not use any other rechargeable baery in your CVM-780.

The CVM-780’s baery recharging circuit is designed for the specied Metal Hydride baer-
ies. Use of any other baery with the CVM baery circuit and recharger may damage the
instrument, can be unsafe by causing overheang and possibly re, which will also void the
instrument’s warranty.
Do not expose the instrument or probe assembly to excessive shock or vibraon. The rubberized protec-
ve boot is intended to minimize mechanical shock and damage. However, it is not a substute for care-
ful handling.

Prostat Warranty
Prostat Corporaon expressly warrants that for a period of one (1) year from the date of purchase, that
Prostat instruments will be free from defects in material (parts) and workmanship (labor). If PROSTAT
receives noce of such defect during the warranty period, Prostat will replace at its expense such parts
that it determines to be defecve. Any defecve part must be returned to PROSTAT postage prepaid with
proof of purchase date.
Warranty Exclusions – THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT
WARRANTIES, EXPRESS AND IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, WHICH ARE SPECIFICALLY DISCLAIMED. The express warranty will not apply to defects or dam-
age due to accidents, neglect, misuse, alteraons, operator error, or failure to properly maintain, clean,
or repair products. Limit of Liability – in no event will Prostat or any seller be responsible or liable for
special, incidental, or consequenal losses or damages, under any legal theory including but not limited
to contract, negligence, or strict liability.
Fulllment by Prostat of its express warranty obligaons described above will be purchaser’s exclusive
remedy and will be Prostat’s and seller’s limit of liability for any breach of warranty or otherwise.