Protech Bs-u830 User manual

USER

MANUAL

BS-U830

Fanless Embedded PC with

Intel®Celeron®/ Pentium®/

Atom®SoC Processor

BS-U830 M1

BS-U830

Fanless Embedded PC with Intel®Celeron® /

Pentium®/ Atom®SoC Processor

All trademarks and registered trademarks mentioned herein are the

property of their respective owners.

This manual is copyrighted in Nov. 2022. You may not reproduce

or transmit in any form or by any means, electronic, or

mechanical, including photocopying and recording.

DISCLAIMER

This user’smanual is meant to assist users in installing and setting up

the system. The information contained in this document is subject to

change without any notice.

CE NOTICE

This is a class A product. In a domestic environment this product may

cause radio interference in which case the user may be required totake

adequate measures.

FCC NOTICE

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment

not expressly approve by the party responsible for compliance could

void your authority to operate such equipment.

CAUTION: Danger of explosion may occur when the battery

is incorrectly replaced. Replace the battery only with the

same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s

instructions.

WARNING: Some internal parts of the system may have high

electrical voltage. We strongly recommend that only qualified

engineers are allowed to s

ervice and disassemble the

system. If any damages should occur on the system and are

caused by unauthorized servicing, it will not be covered by

the product warranty.

Contents

1Introduction ......................................................................................... 1-1

1.1 About This Manual .................................................................... 1-2

2Getting Started .................................................................................... 2-1

2.1 Package List.............................................................................. 2-2

2.2 System Overview ...................................................................... 2-3

2.2.1 Front View ......................................................................... 2-3

2.2.2 Rear View .......................................................................... 2-3

2.2.3 Top View ............................................................................ 2-4

2.2.4 Side View........................................................................... 2-5

2.2.5 Bottom View ...................................................................... 2-6

2.3 System Specifications ............................................................... 2-7

2.4 Safety Precautions .................................................................... 2-9

3System Configuration......................................................................... 3-1

3.1 External System I/O Ports Diagrams ........................................ 3-2

3.1.1 Rear I/O Ports Diagrams ................................................... 3-2

3.2 Jumper & Connector Quick Reference Table............................ 3-2

3.3 Component Locations of System Main Board........................... 3-4

3.3.1 Top View of Main Board BE-U830..................................... 3-4

3.3.2 Jumper Setting of Main Board BE-U830 ........................... 3-5

3.3.3 Bottom View of Main Board BE-U830 .............................3-12

3.4 How to Set Jumpers................................................................3-13

3.5 I/O Ports .................................................................................. 3-15

3.5.1Power Button ................................................................... 3-15

3.5.2 DC In 12/24V ................................................................... 3-15

3.5.3 COM1 Port (COM1).........................................................3-16

3.5.4 COM2 Port (COM2).........................................................3-16

3.5.5 Dual LAN Ports (LAN1, LAN2) ........................................ 3-17

3.5.6 Dual LAN Ports (LAN3, LAN4) (option) ........................... 3-18

3.5.7 3 x 1 USB 2.0 Ports (USB2) ............................................3-19

3.5.8 Dual USB 3.0 Ports (USB1) ............................................ 3-20

3.5.9 Dual USB 2.0 Port (USB3) .............................................. 3-21

3.5.10 Display Port (DP) Port Connector (DP) ...........................3-22

3.5.11 HDMI Connector (HDMI) .................................................3-23

3.5.12 Digital Input/Output Connector (DIO) .............................. 3-24

3.6 Setting Connectors and Jumpers............................................ 3-25

3.6.1 COM1 and COM2 Connector (JCOM1, JCOM2) ............3-25

3.6.2 2 x Internal USB 2.0 Pin Headers (JUSB1)..................... 3-26

3.6.3 Internal USB 2.0 Wafer (JUSB2) ..................................... 3-26

3.6.4 Digital Input / Output Connectors (JDIO1, JDIO2) .......... 3-27

3.6.5 HD Audio Connector (JAUDIO1) .....................................3-28

3.6.6 Mini PCI Express Slot (M_PCIE1)...................................3-29

3.6.7 Micro SIM Card Socket (SIM1)........................................ 3-30

3.6.8 LVDS Inverter Connector (JINV1) ................................... 3-31

3.6.9 LVDS Connector (LVDS1) ............................................... 3-32

3.6.10 M.2 Wi-Fi Express Slot (M2_E1) ..................................... 3-33

3.6.11 M.2 SSD Express Slot (M2_M1) ..................................... 3-35

3.6.12 SATA 3.0 & HDD Power Connectors (SATA1, JHD_PWR1)

......................................................................................... 3-37

3.6.13 RTC Connector (JBAT1).................................................. 3-38

3.6.14 Power LED Connector (JLED1) ...................................... 3-38

3.6.15 Power Button Connector (JBTN1)................................... 3-38

3.6.16 COM1 Port Voltage Selection (JP_COM1)...................... 3-39

3.6.17 USB1 Port Power Selection (JP_USB1) ......................... 3-40

iii

3.6.18 LVDS Voltage Selection (JP_VDD1) ...............................3-41

3.6.19 Low Pin Count Selection (JP_LPC1)...............................3-42

3.6.20 LVDS Sequence Control Selection (JP1) ........................ 3-43

3.6.21 LVDS Backlight Control Selection (JP7).......................... 3-44

3.6.22 Clear CMOS Data Selection (JCOMS1)..........................3-45

4Software Utilities ................................................................................. 4-1

4.1 Introduction................................................................................ 4-2

4.2 Installing Intel®Chipset Software Installation Utility .................. 4-3

4.3 Installing Graphics Driver Utility ................................................ 4-4

4.4 Installing LAN Driver Utility........................................................ 4-5

4.5 Installing Sound Driver Utility .................................................... 4-6

4.6 Installing Intel®Management Engine Components Driver Installer

.................................................................................................. 4-7

5BIOS SETUP ........................................................................................ 5-1

5.1 Introduction................................................................................ 5-2

5.2 Accessing Setup Utility.............................................................. 5-3

5.3 Main........................................................................................... 5-6

5.4 Advanced .................................................................................. 5-8

5.4.1 Advanced – CPU Configuration ........................................ 5-9

5.4.2 Advanced – PCH-FW Configuration................................ 5-10

5.4.3 Advanced – ACPI Settings .............................................. 5-11

5.4.4 Advanced – F81967 Super IO Configuration ..................5-12

F81967 Super IO Configuration – Serial Port 1 Configuration ....5-13

F81967 Super IO Configuration – Serial Port 2 Configuration ....5-14

5.4.5 Advanced – Hardware Monitor........................................ 5-15

5.4.6 Advanced – F81967 Watchdog .......................................5-16

5.4.7 Advanced – S5 RTC Wake Settings................................ 5-17

5.4.8Advanced – PTN3460 EDID Configuration .....................5-18

5.4.9 Advanced – USB Configuration.......................................5-19

5.4.10 Advanced – Network Stack Configuration.......................5-20

5.4.11 Advanced – NVMe Configuration .................................... 5-21

5.5 Chipset .................................................................................... 5-22

5.5.1 Chipset – System Agent (SA) Configuration ...................5-23

System Agent (SA) Configuration – Memory Configuration ........5-24

5.5.2 Chipset – PCH-IO Configuratioin .................................... 5-26

PCH-IO Configuration – PCI Express Configuration...................5-27