protech SA-5800 User manual

USER
MANUAL
SA-5800
Intel®6th/7th Gen.Core
i7/i5/i3/Pentium®/Celeron®
ProcessorBook-SizedPC
SA-5800 M1

SA-5800
Intel®6th/7th Gen. Core  i7/i5/i3/
Pentimu®/ Celeron®Processor
Book-Sized PC
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Feb. 2018. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery
only with the
same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the system may have high
electrical voltage. We strongly recommend that only qualified
engineers are allowed to service
and disassemble the
system. If any damages should occur on the system and are
caused by unauthorized servicing, it will not be covered by
the product warranty.

i
Contents
1Introduction .........................................................................................1-1
1.1 About This Manual ....................................................................1-2
2Getting Started ....................................................................................2-1
2.1 Packing List...............................................................................2-2
2.2 System Specifications ...............................................................2-3
2.3 System Overview ......................................................................2-4
2.3.1 Front View .........................................................................2-4
2.3.2 Rear View..........................................................................2-4
2.3.3 Top View............................................................................2-5
2.3.4 Bottom View ......................................................................2-5
2.3.5 Side View...........................................................................2-6
2.3.6 Quarter View......................................................................2-6
2.4 Safety Precautions....................................................................2-7
3System Configuration.........................................................................3-1
3.1 Rear I/O Ports Diagram.............................................................3-2
3.2 JUMPER & CONNECTOR QUICK REFERENCE TABLE........3-3
3.3 COMPONENT LOCATIONS .....................................................3-5
3.3.1 Top View and Jumper Settings of SA-5800.......................3-5
3.3.2 Bottom View of SA-5800 ...................................................3-6
3.4 HOW TO SET JUMPERS .........................................................3-7
3.5 Setting Connectors and Jumpers..............................................3-9
3.5.1 COM1, COM2 Port Pin9 Definition Selection Guide.........3-9
3.5.2 Dual COM Ports ..............................................................3-10
3.5.3 COM1 RS-232/422/485 Selection...................................3-11

ii
3.5.4 COM1 RS-485 Auto Flow Selection................................3-12
3.5.5 LAN and USB 3.0 Ports...................................................3-13
3.5.6 Internal USB 2.0 Connectors...........................................3-15
3.5.7 VGA Port..........................................................................3-16
3.5.8 DisplayPort (DP) Connector............................................3-17
3.5.9 DC IN 3 Pins Terminal Block (12V) .................................3-18
3.5.10 HD Audio Connector........................................................3-19
3.5.11 Digital Input / Output Connector......................................3-20
3.5.12 Front Panel Connector ....................................................3-21
3.5.13 System Fan Connector....................................................3-22
3.5.14 CPU Fan Connector........................................................3-22
3.5.15 M.2 SSD Connector.........................................................3-23
3.5.16 PCI Express Slot .............................................................3-24
3.5.17 SATA 3.0 Connectors ......................................................3-26
3.5.18 HDD Power Connectors..................................................3-27
3.5.19 ATX Power Input Connector............................................3-27
3.5.20 DIO Port Power Connector..............................................3-28
3.5.21 AT / ATX Mode Selection.................................................3-29
3.5.22 SPI Override Protection Selection...................................3-30
3.5.23 Case Open Detection Connector (option).......................3-30
3.5.24 Low Pin Count (LPC) Connector.....................................3-31
3.5.25 VCCIO Voltage Selection ................................................3-31
3.5.26 Clear CMOS Data Selection............................................3-32
4Software Utilities.................................................................................4-1
4.1 Introduction................................................................................4-2
4.2 Installing Intel®Chipset Software Installation Utility..................4-4
4.3 Intel®Management Engine Components Installer Installation..4-5

iii
4.4 Intel®USB 3.0 eXtensible Host Controller Utility ......................4-6
4.5 Installing Graphics Driver Utility................................................4-7
4.6 Installing LAN Driver Utility........................................................4-8
4.7 Installing Sound Driver Utility....................................................4-9
4.8 Installing Microsoft Hotfix kb3211320 and kb3213986 Driver Utility
................................................................................................... 4-9
5BIOS SETUP ........................................................................................5-1
5.1 Introduction................................................................................5-2
5.2 Accessing Setup Utility..............................................................5-3
5.3 Main...........................................................................................5-6
5.4 Advanced ..................................................................................5-8
5.4.1 Advanced – CPU Configuration ........................................5-9
5.4.2 Advanced – SATA Configuration .....................................5-11
5.4.3 Advanced – PCH-FW Configuration................................5-12
5.4.4 Advanced – Trusted Computing......................................5-13
5.4.5 Advanced – ACPI Settings ..............................................5-14
5.4.6 Advanced – F81866 Super IO Configuration ..................5-15
5.4.7 Advanced – Hardware Monitor........................................5-18
Smart Fan Mode Configuration ...................................................5-19
5.4.8 Advanced – F81866 Watchdog.......................................5-20
5.4.9 Advanced – Network Stack Configuration.......................5-21
5.4.10 Advanced – USB Configuration.......................................5-22
5.5 Chipset ....................................................................................5-23
5.5.1 Chipset – System Agent (SA) Configuration ...................5-24
Chipset – SA Configuration – Memory Configuration..................5-25
Chipset – System Agent (SA) Configuration – Graphics

iv
Configuration ...............................................................................5-27
Chipset –System Agent (SA) Configuration – PEG Port
Configuration...............................................................................5-29
5.5.2 Chipset – PCH-IO Configuration.....................................5-30
5.6 Security ...................................................................................5-31
5.7 Boot.........................................................................................5-33
5.7.1 Boot – CSM Configuration...............................................5-35
5.8 Save & Exit..............................................................................5-37
Appendix A System Diagrams....................................................A-1
SA-5800 I/O Shield Assembly Exploded Diagram....................................A-2
SA-5800 Mother Board and Cooler Exploded Diagram ...........................A-3
SA-5800 Riser Card Assembly Exploded Diagram..................................A-4
SA-5800 HDD / SSD Assembly Exploded Diagram.................................A-5
SA-5800 Top Cover Assembly Exploded Diagram...................................A-6
Appendix B Technical Summary................................................B-1
System Block Diagram .............................................................................B-2
Interrupt Map ............................................................................................B-3
I/O MAP..................................................................................................B-14
Memory Map...........................................................................................B-16
Configuring WatchDog Timer .................................................................B-18
Flash BIOS Update.................................................................................B-20

v
Revision History
The revision history of SA-5800 User Manual is described below:
Version No.
Revision History
Page No.
Date
M1
Initial Release
-
2018/02

SA-5800 SERIES USER MANUAL
Page: 1-1
1 Introduction
This chapter provides the introduction for SA-5800 as well
as the framework of the user manual.
The following topic is included:
•About This Manual

Chapter 1 Introduction
SA-5800 SERIES USER MANUAL
Page: 1-2
1.1 About This Manual
Thank you for purchasing our SA-5800 system. The SA-5800 provides faster
processing speed, greater expandability and can handle more tasks than before. This
manual is designed to assist you how to install and set up the whole system. It
contains 5 chapters and 2 appendixes. Users can configure SA-5800 according to their
own needs. This user manual is intended for service personnel with strong hardware
background. It is not intended for general users.
The following section outlines the structure of this user manual.
Chapter 1 Introduction
This chapter provides the introduction for SA-5800 as well as the framework of the
user manual.
Chapter 2 Getting Started
This chapter describes the package contents and outlines SA-5800 specifications.
Read the safety reminders carefully on how to take care of SA-5800 motherboard
properly.
Chapter 3 System Configuration
This chapter describes the locations and functions of the system motherboard
components. You will learn how to properly configure the connectors and system
configuration jumpers on the motherboard and configure the system to meet your own
needs.
Chapter 4 Software Utilities
This chapter contains helpful information for proper installations of the Intel Chipset
Software Installation Utility, Intel® Management Engine Components Installer, USB
3.0 eXtensible Host Controller Utility, Graphics Driver Utility, LAN Driver Utility,
Sound Driver Utility and Hotfix Driver Utility.
Chapter 5 BIOS Setup
This chapter indicates you how to change the BIOS configurations.
Appendix A System Diagrams
This appendix provides the exploded diagrams and part numbers of the SA-5800.
Appendix B Technical Summary
This appendix provides the information about the allocation maps for SA-5800
system block diagram, system resources, Watchdog Timer Configuration and Flash
BIOS Update.
.