PRYME Radio Product Trooper SPM-2100 User manual

4version 1.00 May 2012
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: [phone]
TOLL FREE: 800.666.2654
WWW.PRYME.COM
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: [phone]
TOLL FREE: 800.666.2654
WWW.PRYME.COM
Trooper® SPM-2100
Heavy Duty Remote Speaker Microphone
USER’S GUIDE FOR REPLACEABLE CABLE
PRYME® is a trademark owned by PRYME Radio Products, Brea, CA.
All other product or service names are the property of their respective owners.
© 2012 PRYME Radio Products, Brea CA. All Rights Reserved
SUPPORT AND WARRANTY
PRYME Radio Products warrants this product against defects in materials or
workmanship for a period of one year from the date of retail purchase. PRYME will
repair or replace a defective unit, at our option, without charge for parts or labor.
The limited warranty is extended only to the original purchaser and is valid only to
consumers in the United States and Canada. It does not cover damage or failure
caused by or attributable to Acts of God, abuse, misuse, improper or abnormal
usage, faulty installation, improper maintenance, lightning, or other incidences of
excessive voltage, or any tampering or repairs by other than a PRYME authorized
repair facility. It does not cover replacement of consumable parts, transportation
costs, or damage in transit.
Repair or replacement under the terms of this warranty does not extend the terms
of this warranty. This warranty can only be modied by an ocer of PRYME Radio
Products, and then only in writing. Should this product prove defective in workman-
ship or material, the consumer’s sole remedies shall be such repair or replacement as
provided by the terms of this warranty. Under no circumstances shall PRYME Radio
Products be liable for any loss or damage, direct, consequential, or incidental, arising
out of the use of or inability to use this product. Some states do not allow limitations
on how long an implied warranty lasts or the exclusions or limitations of incidental or
consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives you specic legal rights. You may also have other rights, which
may vary, from state to state.
For support or warranty service on your PRYME product, contact us at 1-800-666-
2654 or visit us on the web at www.PRYME.com.
COPYRIGHT AND TRADEMARK INFO
© 2012 PRYME Radio Products, Brea CA. All rights reserved. PRYME® is a trademark
owned by PRYME Radio Products. All other product or service names are the property
of their respective owners.
version 1.00 May 2012
Microphone Head
Replaceable Cable
Assembled SPM-2100

2 3
4. Insert the small athead screwdriver under the locking tab of the RJ45 connector
and push the tab up.
STEP TWO: ATTACHING THE NEW CABLE
1. Insert the RJ45 connector on the new
microphone cable into the jack on the
SPM-2100 TROOPER microphone head.
The tab of the RJ45 connector should be
on the back side of the microphone head.
2. Push the RJ45 connector into the jack
until the tab "clicks" and locks into place.
3. Slide the protective rubber boot up
the microphone cable and over the RJ45
jack on the SPM-2100 TROOPER
microphone head until is completely
covers the jack. This boot keeps dust,
dirt, and moisture out of the RJ45 jack
and the microphone should not be
operated unless it is in place.
2. Using the screwdriver as a
lever, push the boot down o
the mic head.
3. Once the boot is clear of the mic head, push
it down the cable away from the microphone
to expose the RJ45 (telephone handset style)
connector.
In order to install a new microphone cable, you
will rst need to remove any microphone cable
that is currently installed on your SPM-2100 series
TROOPER microphone. If no mic cable is installed,
skip to STEP TWO on next page.
1. Remove the protective rubber boot that
covers the RJ45 connector on the bottom of the
TROOPER microphone head. To do this, insert a
small athead screw driver under the rubber boot,
between the boot and the microphone head.
TOOLS: To replace the microphone cable, you will need a small at head screwdriver.
STEP ONE: REMOVE THE EXISTING CABLE (IF NEEDED)
Removing and Replacing the Cable for the SPM-2100
5. Once the tab had been pushed up,
the cable should be "unlocked" from
the microphone. Pull the cable out of
the microphone head. The cable and
microphone head should now be
separate from each other.
‘CLICK’