Pulsar AWZ525 User manual

1
AWZ525
v.1.0
PC3
Time Relay Module
Edition: 1 from 02.03.2015
Replaces edition: -------------- EN**
The module’s features:
10 ÷ 14V DC power supply
extension of the trigger pulse for the time set
time range from 1 second to 5 min.
Relay output
Activated by plus "S +" or ground (minus) „S-„
Optical indication of power supply, triggering signal
and relay output status
Warranty - 2 years from the production date
CONTENTS.
1. General description
2. Components arrangement
3. Specifications
4. Operating modes
1. General description.
The PC3 time module is a transceiver that allows extending the trigger pulse for a short period of time set
by the potentiometer. The device can operate in two modes: extension of time activated by the pulse or by the
triggering signal loss. The range of the measured times is between 1s. - 5 minutes.
2. Components arrangement.
The figure below shows the arrangement of the most important components and connectors of the relay
module.
Fig.1. The view of the module.

2
Table 1. The description of components and connectors of the module.
3. Specifications
No.
[Fig.1]
Description
Connector:
+12V- - The module’s power supply, DC voltage
S+ - control input supplied by the positive power supply
S- - control input activated by the negative power supply (power supply minus)
–REL relay connector
CAUTION ! In Fig.1 the set of contacts shows a potential-free status of the relay.
LED (green): –optical indication
green –supply voltage
green –trigger signal indication (S + or S-)
red –The REL relay activation indication –(the LED is on when the relay is activated )
Operating mode jumper:
mode 1
mode 2
Description: jumper on, jumper on
Time range jumper:
1s –60s. time range
5s –5 min. time range
Description: jumper on, jumper on
Potentiometer for time adjustment
Relay
Supply voltage
10÷14V DC
Power consumption
5 mA/25 mA (inactive/active relay) (±5%)
S+ input
10÷14V DC control
S- input
0V (GND) control
Time range
Range 1: 1s ÷ 60s
Range 2: 5s ÷ 5 min
The number of relays
1
Maximum connection voltage
50V AC /30V DC
Maximum connection current
1 A
Maximum contact resistance
<100 mOhm
Optical indication of operation
LED light
Operation parameters
II environmental class,
-10°C - 40°C, relative humidity Rh=75%max. No condensation.
Dimensions
59 x 43 x 21 (WxHxD)
Mounting
mounting tape or dowel pins x2 (holes3mm)
Connectors
Ф0,51÷2,05 mm (AWG 24-12)
Net/gross weight
0,03 /0,05 [kg]

3
4. Operation modes.
The time module can operate in two modes:
- Mode 1 (jumper on)
- The triggering signal activates the relay. The system waits for a trigger signal loss. After the signal loss, the T
time countdown begins.
Once the countdown is finished, if no new triggering signal is generated, the relay will switch off.
If a triggering signal is generated during the T time countdown, the T time countdown will start with the S
triggering signal loss.
- Mode 2 (jumper off)
- The S triggering signal activates the relay for the T time period. If a triggering signal is longer than the T time,
the relay will switch off with the triggering signal loss.
Fig.2 Time diagrams of the module.

4
Pulsar
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax [phone]
E-mail: [email protected], [email protected]
http:// www.pulsar.pl, www.zasilacze.pl
WARRANTY
Pulsar (the manufacturer) grants a two -year warranty for the
equipment, counted from the device’s production date.
WEEE LABEL
According to the European Union WEEE Directive, waste electrical and electronic equipment should be disposed of separately from
normal household waste. Waste electrical and electronic equipment must not be disposed of with normal household waste.