Pulsar MSRD 1024 User manual

MSRD 1024
v.1.0
MSRD 27,6V/1A
Buffer switch mode power supply module
EN
Edition: 1st (14th Mar 2012)
Supercedes:---------------

www.pulsar.pl MSRD1024
2
CONTENTS:
1. Technical description.
1.1 General description
1.2. Block diagram
1.3. Description of components and connectors
1.4. Specifications
2. Installation.
2.1 Requirements
2.2 Installation procedure
3. Operating status indication.
3.1 LED indication
3.2. Technical outputs
4. Operation and use
4.1. Overload or short circuit of the PSU module output
4.2. Battery-assisted operation
4.3. Maintenance
1. Technical description
1.1 General description
A buffer PSU module is intended for an uninterrupted supply to alarm systems devices requiring stabilised
voltage of 24V/DC (+/-15%). The PSU module provides voltage of 27,6 V DC with current capacity:
1. Output current 1A (without a battery)
2. Output current 0,8A + 0,2A battery charge
3. Output current 0,5A + 0,5A battery charge
Total current of the receivers + battery: 1A max.
In case of power failure, a battery back-up is activated immediately. The battery charging current is preset to 0,2A.
Features:
•Uninterrupted supply of 27,6VDC/1A
•supply voltage: external transformer required
27-30VAC (AWT5172430, AWT049)
•high efficiency 85%
•battery charging and maintenance control
•deep discharge battery protection (UVP)
•battery output protection against short-circuit and
reverse polarity connection
•jumper selectable battery charging current
0,2A/0,5A
•battery fuse status control
•LED indication
• START facility for manual battery connection
• STOP button for battery disconnection during
battery-assisted operation
•FAC technical output indicating AC power
collapse
•FPS technical output indicating PSU failure
•protections:
•SCP short-circuit protection
•OLP overload protection
•surge protection

www.pulsar.pl MSRD1024
3
1.2. Block diagram.
Fig.1. Block diagram of the PSU module
1.3. Description of components and connectors (Fig.2, tab.1).
Table 1. Description of components and connectors (see Fig. 1).
Element no. Description
[1] AC, AUX, LB, F
BAT
LED indication for PSU module operating status
[2] FAC - technical output for no AC network - relay type Caution! In Fig.2. the set of contacts indicates potential-free status which corresponds to AC
power outage (AC power failure).
[3]
Technical outputs, open collector type:
FAC - AC absence technical output
normal status - L level (0V),
failure status: hi-Z level
indication time lag: approx. 10 sec.
GND – joint terminal (-)
FPS – technical output of the PSU failure – OC type
normal status - L level (0V),
failure status: hi-Z level
[4]
I
BAT
; pin – battery charging current adjustment
•I
BAT
= , Ibat =0,2A
•I
BAT
= , Ibat =0,5A
Caption: jumper on, jumper off
[5] V
ADJ
potentiometer, DC voltage adjustment
[6] F
BAT
fuse in the battery circuit
[7] STOP button (PSU module disconnection from the battery)
[8] START button (launching the PSU module from a battery)
[9]
Connectors:
+BAT- DC supply output (+BAT= red, -BAT = black)
+AUX- DC power output (+AUX= +U, -AUX=GND)
~AC~ – AC power input (27V-30V AC (e.g.AWT5172430, AWT049)

www.pulsar.pl MSRD1024
4
Fig. 2. The view of the PSU module
1.4. Specifications:
- electrical specifications (tab.2)
- mechanical specifications (tab.3)
- operating specifications (tab.4)
Electrical specifications (tab. 2).
Supply voltage 27V÷30V/AC (e.g.AWT5172430, AWT049)
Current consumption 1,6 A max.
Power frequency 50Hz
PSU power 28W
Efficiency 85%
Output voltage 22,0V÷27,6Vdc – buffer operation
20,0V÷27,6Vdc – battery-assisted operation
Output current 1A without a battery
0,8A + 0,2A battery charge
0,5A + 0,5A battery charge
Output voltage escalation, decrease, and keeping
time 20ms/40ms/12ms @Izn., Uac=min.
Voltage adjustment range 24,0 V÷ 28 V
Ripple voltage 40mV p-p max.
Current drawn by the PSU module systems 25 mA max.
Battery charging current 0,2A / 0,5A – I
BAT
jumper selectable
Short-circuit protection SCP 200% ÷ 250% of PSU module power - current limitation
and/or fuse damage in the battery circuit (fuse-element
replacement required)
Overload protection OLP
110% ÷ 150% (@25ºC÷55ºC) of PSU module power -
current limitation with the PTC resettable fuse, manual
restart (failure requires disconnection of the DC output
circuit)
Battery circuit SCP and reverse polarity
protections 2A- current limitation, F
BAT
fuse (failure requires fuse-
element replacement)
Deep discharge battery protection UVP U<20,0 V (± 5%) – disconnection (-BAT) of the battery

www.pulsar.pl MSRD1024
5
Technical outputs:
- FAC; output indicating failure of AC power
supply
- FPS; technical output of the PSU operation
status
-R – relay type, 1A@ 30Vdc/50Vac max.
CAUTION! In Fig.2. the set of contacts indicates potential-
free status which corresponds to AC power outage (AC
power failure)
- OC type, 50mA max., normal status: L (0V) level, failure:
hi-Z level, time lag: 10s.
- OC type, 50mA max. normal status: L (0V) level, failure:
hi-Z level (automatic return after restoration of correct
operation)
LED indication
- AC diode indicating AC power
- AUX diode indicating DC at the PSU output
- LB diode indicating battery charging process
- F
BAT
diode indicating battery fuse status
- red, normal status: permanently illuminated
- green, normal status: permanently illuminated
- yellow, the light intensity depends on battery charging
current
- blue, normal status: off, fuse failure: permanently
illuminated
F
BAT
fuse F 2A
Mechanical specifications (tab. 3).
Enclosure dimensions 70 x 69 x 89 (WxHxD)
Fixing on DIN TH35 rail
Net/gross weight 0,19kg/0,25kg
Enclosure plastic, white
Connectors power supply, outputs, battery outputs, technical outputs:
Φ0,63÷2,50 (AWG 22-10)
Operating specifications (tab.4).
Operating temperature -10ºC...+40ºC
Storage temperature -20ºC...+60ºC
Relative humidity 20%...90%, without condensation
Vibrations during operation unacceptable
Impulse waves during operation unacceptable
Direct insolation unacceptable
Vibrations and impulse waves during transport PN-83/T-42106
2. Installation.
2.1 Requirements
The buffer PSUmodule is to be mounted by a qualified installer, holding relevant permits and licenses
(applicable and required for a given country) for 230V/AC interference and low-voltage installations. The unit
should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative
humidity (RH=90% maximum, without condensation) and temperature from -10°C to +40°C. The PSU module sh all
work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of the enclosure.
The PSU module provides voltage of 27,6 V DC with current capacity:
1. Output current 1A (without a battery)
2. Output current 0,8A + 0,2A battery charge
3. Output current 0,5A + 0,5A battery charge
Total current of the receivers + battery: 1A max.
As the PSU module is designed for a continuous operation and is not equipped with a power-switch,
therefore an appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user
shall be informed about the method of unplugging (most frequently through separating and assigning an
appropriate fuse in the fuse-box). The electrical system shall follow valid standards and regulations.
The device should be installed in the metallic enclosure, distribution board (ICT cabinet) equipped with a DIN TH35
rail (35 mm wide). In order to meet the UE requirements, the rules concerning: supply, development and shielding

www.pulsar.pl MSRD1024
6
ought to be followed- accordingly to the application. The module requires 27-30V AC power supply with galvanic
separation (transformer insulation). The minimum power of the transformer: 40VA.
2.2 Installation procedure
1. Install an enclosure, a distribution board or a cabinet and lead the cables through the cable ducts.
2. Install the PSU module on the DIN rail: Mount the module onto the rail and block with a clip (Fig. 3)
3. Deliver the output voltage from the AC transformer to the ~AC~ terminals (27-30V, min40VA).
4. Connect the receivers’ cables to the +AUX, -AUX terminals of the terminal block on the PSU module’s board.
5. If necessary, connect the device conductors to the technical output, two pairs of contacts Cx-NCx-NOx
(alarm panel, controller, indicator, LED, etc.)
6. Activate the ~230V/AC supply (the AC red diode and AUX green diode should be permanently illuminated)
7. Check the output voltage (the PSU module voltage without load should amount to 27,6V-27,8V, during battery
charging 22,0-27,6VV). If the value of the voltage requires adjustment, it should be set by the V
adj
potentiometer,
monitoring the voltage at the AUX output of the PSU module.
8. Connect the battery in accordance with the signs: +BAT red to ‘plus’, -BAT black to ‘minus’, (the LB red diode will
be lit and the light should fade throughout the time of charging).
9. Once the tests and operation control have been completed, the enclosure/cabinet can be locked.
Rys.3. Mounting on a DIN rail.
3. Operating status indication.
3.1 LED indication
The PSU module is equipped with four diodes indicating operating status: AC, LB, AUX, F
BAT
.
•AC- red diode: under normal status (AC supply) the diode is permanently illuminated. The absence of AC
supply is indicated by the AC diode going out.
•AUX- green diode: indicates the DC supply status in the output of the PSU module. Under normal status,
the diode is permanently illuminated. In case of a short circuit or overload the diode goes out.
•LB- yellow diode: indicates battery charging process, the light intensity depends on the battery charging
current: 0,5A=100%.......0,0A=0%.
•F
BAT
- blue diode: under normal status, it is off. In case of fuse damage (burnt fuse-) the diode is lit.
3.2 Technical outputs
The PSU module is equipped with indication outputs:
•FAC - absence of AC supply output: - OC type output indicating AC power loss. In normal status, with
230V AC supply, the output is connected to ground (L level– 0V). In case of power loss, the PSU will switch
the output into a high impendence state, hi-Z, after 10 seconds.
•FAC - absence of AC supply output: - relay output indicating the absence of AC supply. In case of power
loss, the PSU module will switch the relay contacts after approx. 10 seconds.
CAUTION! In Fig.2. the contact set in the potential-free status corresponds to a state with no AC
power (AC power failure).
•FPS - technical output of the PSU operation status: OC type output indicating the PSU failure. In
normal state (during correct operation) the output is connected to ground (L level – 0V). In case of incorrect
operating parameters (voltage, current, temperature), the output is switched into a high impendance state –
hi-Z.

www.pulsar.pl MSRD1024
7
4. Operation and use.
4.1 Overload or short circuit of the PSU module output
The AUX output of the PSU module is equipped with the PTC polymer fuse assisted protection. If the load
of the PSU module exceeds 1A (load 110% ÷ 150% @25ºC of the PSU module power), the output voltage is
automatically cut off and indicated by the green diode going out. To restore the output power, cut off the output
load for approximately 1 minute.
In case of a short-circuit in the AUX, BAT output, (load 200% ÷ 250% of the PSU module power) or reverse
battery connection, the F
BAT
fuse in the battery circuit becomes permanently damaged and the restoration of the
voltage at the BAT output requires the replacement of the fuse.
4.2 Battery assisted operation
In case of the main power outage, the device is immediately switched into a battery-assisted operation.
In order to run the PSU module from the battery only, connect the BAT connectors in accordance with the
signs:
+ BAT red to ‘plus’ and, - BAT black to 'minus’ then press the START button on the main board and hold it for 5
seconds.
The PSU module is equipped with the discharged battery disconnection system (UVP).
4.3 Maintenance
Any and all maintenance operations may be performed following the disconnection of the PSU module from
the power supply network. The PSU module does not require performing any specific maintenance measures,
however, in case of significant dust rate, its interior is recommended to be cleaned with compressed air. In case of
fuse replacement, use a replacement of the same parameters.

www.pulsar.pl MSRD1024
8
WEEE MARK
According to the EU WEE Directive – It is required not to dispose of electric or
electronic waste as unsorted municipal waste and to collect such WEEE separatel .
The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed
of but recycled according to the applicable law.
GENERAL WARRANTY CONDITIONS
1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a two-year warranty for the equipment starting from the initial product date
of purchase placed on the receipt.
2. If a purchase proof is missing a three-year warranty period is counted from the device’s production date.
3. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the
manufacturer’s discretion) if the malfunction is due to the manufacturer includes manufacturing or material defects unless such
defects have been reported within the warranty period (item 1 and 2).
4. The equipment subject to warranty is to be brought to the place where it was purchased or directly to the main office of the
manufacturer.
5. The warranty applies to complete equipment accompanied by a properly filled warranty claim with a description of the defect.
6. Should the claim be accepted the manufacturer is obliged to provide warranty repairs at the earliest convenience however not
later that within 14 days from the delivery to the service centre of the manufacturer.
7. The repair period mentioned in item 6 may be prolonged if there are no technical possibilities to carry out the repairs or if the
equipment has been conditionally accepted due to the breaking warranty terms by the claimant.
8. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer exclusively.
9. The warranty does not cover the defects of the equipment resulting from:
- reasons beyond the manufacturer's control
- mechanical damage
- improper storage and transport
- use that violates the operation manual or equipment’s intended use
- fortuitous events including lightning discharges power failures fire flood high temperatures and chemical agents
- improper installation and configuration (in defiance with the manual)
10. The warranty is void in any of the following circumstances:
- construction changes
- repairs carried out by any unauthorized service center
- damage or removal of warranty labels
- modifications of the serial number
11. The liability of the manufacturer towards the buyer is limited to the value of the equipment determined according to the
wholesale prices suggested by the manufacturer on the day of purchase.
12. The manufacturer takes no responsibility for the defects that result from:
- the damaging malfunctioning or inability to operate the equipment
- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the
recommendations and requirements contained in the manual or the use of the equipment.
Pulsar K.Bogusz Sp.j.
Siedlec 150 32-744 Łapczyca Poland
Tel. [phone] Fax. [phone]
e-mail: [e-mail] [e-mail]
http:// www.pulsar.pl