Pulsar MSEP412V User manual

1
MSEP412V
v.1.0
MSEP video module 4 channels BNC
EN**
Edition: 1 from 24.09.2013
Supercedes the edition: ---------
Features:
 BNC connector for connecting the video signal
 video signal’s detection
 four channels of video input/output
 four channels of power supply (max. 4x1A)
 LED indication
 warranty – 5 year from the production date
1. Technical description.
The 4-channel video module is intended for CCTV systems where the video signal and the cameras’ supply are
delivered using a 75 ohm coaxial cable integrated with two power wires (YAP type).The module enables connecting 4
camcorders and 4 independent power supply units which can work within the same earth potential. MSEP412V does
not have galvanic insolation, either between the input and the output, or between individual channels. The module is
intended for working in connection with the PSBSEP04124 power supply unit, featuring 4 supplying channels with
independent adjustment of output voltage, within the range of 12÷18V.
Fig.1. Example of the module’s application.

2
1.1. Description of the module’s components and connectors (fig2, tab.1)
Table 1.
No
[rys.2] Description
[1] Connectors:
-OUT1+ … -OUT4+ - output voltage for supplying the cameras
[2] Connectors:
-IN1+ … -IN4+ - DC input power
[3] Connector BNC: input of the camera’s video signal
[4] Connector BNC: output of the video signal to the recorder
[5] LED L1…L4 – yellow diodes indicating presence of video signal in individual video
channels
[6] LED DC – green diode indicating presence of DC input power
Fig.2. The view of the MSEP412V video module.
2. Specifications:
- electrical specifications (tab.2)
- mechanical specifications (tab.3)
- operating specifications (tab.4)
Table 2.
Supply voltage 8V÷30V/DC
Output voltage consistent with the supply voltage
Number of video inputs/outputs 4
Output current 4x1A max.
Current consumption by the module’s systems 30 mA max.
LED indication:
- DC diode indicating DC power status
- L1…L4 diode indicating presence of video
signal in individual video channels
- green, normal status: permanently illuminated
- yellow, normal status: permanently illuminated
Operating conditions 2nd environmental class, -10°C ÷40°C
Table 3.
Dimensions 38 x 270 x 25 (WxLxH) [mm]
Fixing dowel pins x 10 (PCB fi=4,2 mm)
Connectors Supply: Ф0,41÷1,63 (AWG 26-14)
Video: BNC
Net/gross weight 0,10/0,14kg
Operating specifications (tab.4).
Operating temperature -10ºC...+40ºC
Storage temperature -20ºC...+60ºC
Relative humidity 20%...90%, without condensation
Vibrations during operation unacceptable
Impulse waves during operation unacceptable
Direct insolation unacceptable
Vibrations and impulse waves during transport PN-83/T-42106

3
3. Installation.
3.1. Requirements.
The module is to be mounted by a qualified installer, holding relevant permits and licenses (applicable and
required for a given country) for 230V/AC interference and low-voltage installations. The unit should be mounted in
confined spaces, in accordance with the 2nd environmental class, with normal relative humidity (RH=90% maximum,
without condensation) and temperature from -10°C to +40°C.
Before installation, define the maximum distance between the module and the supplied camera, taking into
account voltage drops at the wires and the camera’s minimum voltage.
3.2. Installation procedure.
1. Mount the video module on dowel pins, inside the enclosure (the dowel pins shall be fixed prior to the installation of
the enclosure/cabinet).
2. Lead the DC voltage to the +IN1-…+IN-4 terminals, keeping the polarisation.
3. Connect the receivers’ wires to +OUT1-…+OUT4- connectors on the module’s board.
4. Connect the video signal to the receivers and recorder to BNC sockets.
5. Connect the DC power (green LED should be permanently illuminated).
6. Once the tests and operation control have been completed, the enclosure/cabinet can be locked.
4. LED indication.
The module features LEDs indicating operating status:
 DC - green diode: under normal status (DC supply) the diode is permanently illuminated. The absence of DC
supply is indicated by the diode going out.
 L1…L4 - yellow diodes: indicate presence of the video signal. Under normal status (presence of video
signal) the diodes are permanently illuminated. If the camera is off, or there is no video signal – the diodes are
off.
5. Operation and use.
Since the video module is not equipped with an overload/a short-circuit protection, it must be provided by using an
appropriate power supply unit (e.g. PSBSEP04124) or a fuse strip.
6. Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the power
supply network. The PSU does not require performing any specific maintenance measures. However, in case of a
thick dust layer, clean the PSU only with compressed air.

4
WEEE MARK
According to the EU WEE Directive – It is required not to dispose of electric or electronic waste
as unsorted municipal waste and to collect such WEEE separately.
Pulsar K.Bogusz Sp.j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [e-mail], [e-mail]
http:// www.pulsar.pl, www.zasilacze.pl
GENERAL WARRANTY CONDITIONS
1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a five-years warranty for the equipment, counted from the
device’s production date.
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the
manufacturer’s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects,
unless such defects have been reported within the warranty period (item 1).
3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main
office of the manufacturer.
4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description
of the defect.
5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest
convenienve, however not later that within 14 days from the delivery to the service centre of the manufacturer.
6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the
repairs, or if the equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.
7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer,
exclusively.
8. The warranty does not cover the defects of the equipment, resulting from:
- reasons beyond the manufacturer's control,
- mechanical damage,
- improper storage and transport,
- use that violates the operation manual or equipment’s intended use
- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical
agents,
- improper installation and configuration (in defiance with the manual),
9. The warranty is void in any of the following circumstances:
- construction changes
- repairs carried out by any unauthorized service center
- damage or removal of warranty labels
- modifications of the serial number
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined
according to the wholesale prices suggested by the manufacturer on the day of purchase.
11. The manufacturer takes no reponsibility for the defects that result from:
- the damaging, malfunctioning or inability to operate the equipment
- defects that result from using the equipment outside its stated specifications and operating parameters failing to
abide by the recommendations and requirements contained in the manual, or the use of the equipment.