Pulsar MSRK 3024 User manual

MSRK 3024
v.1.0
MSRK 27,6V/3A/OC
Buffer, switch mode power supply module
with technical outputs.
EN**
Edition: 2 from 11.05.2015
Supersedes the edition: 1 from 11.06.2014

www.pulsar.pl MSRK3024
2
Features:
DC 27,6V/3A uninterruptible power supply
high efficiency 92%
low voltage ripple
battery charging and maintenance control
excessive discharging (UVP) protection
battery output full protection against short-circuit
and reverse polarity connection
jumper selectable battery charge current 0,5A/1A
START facility for manual battery connection
LED indication
EPS technical output indicating AC power loss
–OC type
PSU technical output indicating PSU failure –OC type
LoB technical output indicating battery low voltage
–OC type
adjustable times indicating AC power failure
protections:
SCP short-circuit protection
OLP overload protection
OHP overheat protection
overvoltage protection
warranty –5 year from the production date
CONTENTS:
1. Technical description.
1.1. General description.
1.2. Block diagram.
1.3. Description of components and connectors.
1.4. Specifications.
2. Installation.
2.1. Requirements.
2.2. Installation procedure.
3. Operating status indication.
3.1. LED indication.
3.2. Technical outputs.
4. Operation and use.
4.1. Overload or short circuit of the PSU module output.
4.2. Running the PSU module from the bartery.
4.3. Deep discharge battery protection UVP.
4.4. Maintenance.
1. Technical description.
1.1 General description.
A buffer PSU module is intended for an uninterrupted supply to devices requiring stabilised voltage of 24V
DC (+/-15%). The PSU module provides voltage of 27,6V DC with current capacity:
1. Output current 3A + 0,5A battery charge
2. Output current 2,5A + 1A battery charge
Total device current + battery: 3,5A max.
In case of power failure, a battery back-up is activated immediately.

www.pulsar.pl MSRK3024
3
1.2. Block diagram (fig.1)
Fig.1. Block diagram of the PSU module
1.3. Description of components and connectors PSU module.
Table 1. Elements of the PSU module pcb (fig. 2).
Element no.
Description
[1]
PBAT; pins - configuration of UVP battery protection function
PBAT = protection (disconnection) of the battery off
PBAT = protection (disconnection) of the battery on
TAC; pins TAC - configuration of time lag of AC failure indication
TAC = time lag T= 10s
TAC = time lag T= 60s
Legend: jumper installed jumper removed
[2]
START button (launching from battery)
[3]
VADJ potentiometer, DC 24 ÷ 29V adjustment
[4]
FBAT fuse in the battery circuit, F5A / 250V
[5]
Terminals:
~AC~ –AC power input
EPS –technical output of AC power failure indication
hi-Z state = AC power failure
0V state = AC power - O.K.
PSU –technical output of PSU failure indication
hi-Z state = failure
0V state = PSU status O.K.
LoB –technical output of low battery voltage indication
hi-Z state = battery voltage UBAT <23V
0V state= battery O.K.
+BAT- –terminals for battery connection
+AUX- –DC power output, (+AUX= +U, -AUX=GND)
Description: hi-Z –high impedance, 0V –connection to the ground GND
[6]
LEDs –optical indication:
AC - AC voltage
LB - battery charge
AUX - output voltage DC
[7]
Connector to the external LED indicators.
[8]
IBAT jumper–battery charging current selection
IBAT = Ibat =0,5A
IBAT = Ibat =1A
Legend: jumper installed jumper removed

www.pulsar.pl MSRK3024
4
Fig.2. View of the PSU module
1.4 Specifications:
- electrical parameters (tab.3)
- mechanical parameters (tab.4)
- operating parameters (tab.5)
Electrical parameters (tab. 3).
Mains supply
33V AC
150VA min. (e.g. AWT034)
Current up to
5,4 A max.
Power frequency
50Hz
Power
97 W
Efficiency
92%
Output voltage
22V÷ 27,6V DC –buffer operation
20V÷ 27,6V DC –battery-assisted operation
Output current
3A + 0,5A battery charge
2,5A + 1A battery charge
Voltage adjustment range
24V÷ 29V DC
Ripple
130 mV p-p max.
Current consumption by PSU module systems
20 mA
Battery charging current
0,5A / 1A - jumper selectable
Short-circuit protection SCP
Electronic - current limitation and/or activation of the FBAT
melting fuse in the battery circuit (failure requires fuse
replacement). Automatic return.
Overload protection OLP
110% ÷ 150% (@25ºC) of power supply, manual restart (the
fault requires disconnection of the DC output circuit)
Battery circuit SCP and reverse polarity protections
F 5A - current limitation, FBAT fuse (in case of a failure, fuse-
element replacement required)
Surge protection
varistors
Excessive discharge protection UVP
U<20V (± 5%) –disconnect of connection battery,
configuration by the PBAT jumper
LED indication:
- AC diode indicating AC power
- AUX diode indicating DC at the PSU output
- LB diode indicating battery charging process
- red, normal status: permanently illuminated, failure: off
- green, normal status: permanently illuminated, failure: off
- yellow, the light intensity depends on battery charging
current

www.pulsar.pl MSRK3024
5
Technical outputs:
- EPS; output indicating AC power failure
- PSU; output indicating DC absence / PSU
module failure
- LoB output indicating battery low voltage
-OC type: 50mA max.
Normal operation: L state (0V),
failure: hi-Z state,
- delay time 10s/60s (+/-20%) –jumper selectable TAC
- OC type: 50mA max.
Normal operation: L state (0V),
failure: hi-Z state,
- OC type, 50mA max.
Normal operation (UBAT >23V): L state (0V),
failure (UBAT <23V): hi-Z state
FBAT fuse
F5A / 250V
Mechanical parameters (tab. 4).
Enclosure dimensions
105 x 143 x 44 (WxLxH) [mm] (+/- 2)
Fixation
Dowel pins x4 (PCB fi=4,2 mm)
Net/gross weight
0,22kg/0,35kg
Connectors
Outputs: Ф0,41÷1,63 (AWG 26-14)
Battery output BAT: 6,3F-2,5, 30cm
Operating parameters (tab.5).
Environmental class
II
Operating temperature
-10ºC...+40ºC
Storage temperature
-20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
According to PN-83/T-42106
2. Installation.
2.1. Requirements.
The buffer PSU module is to be mounted by a qualified installer, holding relevant permits and licenses
(applicable and required for a given country) for 230V/AC and low-voltage installations. The unit should be mounted in
confined spaces, in accordance with the II-nd environmental class, with normal relative humidity (RH=90% maximum,
without condensing) and temperature from -10°C to +40°C.
The unit should be mounted in a metal enclosure (cabinet) in a vertical position so as to ensure free, convection
air flow through the vents.
In order to meet the EU requirements, follow the guidelines on: power supply, enclosures and shielding:
- according to application. The module requires 33V AC power supply with galvanic. (transformer) isolation.
1. Output current 3A + 0,5A battery charge
2. Output current 2,5A + 1A battery charge
Total device current + battery: 3,5A max.
As the PSU module is designed for a continuous operation and is not equipped with a power-switch,
therefore an appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be
informed about the method of unplugging (most frequently through separating and assigning an appropriate fuse in the
fuse-box). The electrical system shall follow valid standards and regulations.
2.2. Installation procedure.
1. Before installation, cut off the voltage in the 230V power-supply circuit.
2. Install the enclosure or cabinet and lead the cables through the cable ducts.
3. Install the PSU module on mounting pins (the mounting pins should be installed before the assembly of the
enclosure/cabinet).
4. Deliver the AC voltage to the ~AC~ terminals.
5. Connect the receivers’ cables to the +AUX, -AUX terminals of the terminal box on the PSU board.
6. If needed, connect the device cables to the technical outputs:
- EPS; technical output indicating AC power failure
- PSU; technical output indicating PSU failure.
- LoB; technical output indicating low battery voltage
7. Using the IBAT pins, determine the maximum battery charging current the should be determine, in accordance with
battery parameters.

www.pulsar.pl MSRK3024
6
8. Using the PBAT pins, determine whether the function of disconnecting the discharged battery U<20V (+/-5%) is to be on
or off. The battery protection is on if the PBAT jumper is removed.
Make the connections between the battery and the power supply panel paying special attention to the correct polarity.
9.Connect the ~ 230V AC power to the transformer. The corresponding LEDs on the PCB of the power supply module
should be ON: red AC and green AUX LED. The yellow LB LED should be ON during battery charging.
11. Check the output voltage (the PSU voltage without load should amount to 27,2V÷ 27,8V, during battery charging
22V÷ 27,6V). If the value of the voltage requires adjustment, it should be set by the VADJ potentiometer, monitoring the
voltage at the AUX output of the PSU module.
12. Check the current consumption of the receivers, taking into account the battery charging current, so as not to exceed
the total current efficiency of the PSU (section 1.1).
13. Once the tests and control operation have been completed, close the enclosure/cabinet.
3. Operating status indication.
3.1 LED indication.
The PSU module is equipped with three diodes indicating operating status: AC, LB, AUX.
AC- red diode: under normal status (AC supply) the diode is permanently illuminated. The absence of AC
supply is indicated by the AC diode going off.
LB - yellow diode: indicates the battery charging process; the intensity of illumination is dependent on the
charging current.
AUX- green diode: indicates the DC supply status in the output of the PSU module. Under normal status,
the diode is permanently illuminated and in case of a short-circuit or overload, the diode goes off.
3.2. Technical outputs
The PSU module is equipped with indication outputs:
EPS - technical output indicating AC power failure.
The output indicates AC power failure. Under normal status –with the AC supply on, the output is shorted
to ground GND. In case of power failure, the PSU will switch the output into hi-Z high impedance state after
a time set by the TAC jumper.
PSU –output indicating failure PSU module.
The output indicates failure PSU module. Under normal status (correct operation) the output is shorted to
ground GND. If there is no DC voltage at the output (eg short circuit), the output is switched into hi-Z high
impedance state.
PSU failure can be caused by the following events:
- Short circuit at the output
- Output overload
- DC/DC voltage converter failure
- Under voltage protection activation
LoB –output indicating low battery voltage.
The output indicates low battery voltage. Under normal status (UBAT > 23V) the output is shorted to ground
GND, when the battery voltage drops too low (UBAT < 23V) the output is switched into hi-Z high impedance
state.
The power supply technical outputs are open collector (OC) type, as shown schematically below.
Fig. 3. Electrical diagram of OC technical outputs.

www.pulsar.pl MSRK3024
7
4. Operation and use.
4.1 Overload or short circuit of the PSU module output.
The AUX output of the PSU module is equipped with the PTC polymer fuse assisted protection. If the load
of the PSU module exceeds Imax (load 110% ÷ 150% @25ºC of the PSU module power), the output voltage is
automatically cut off and indicated by the green diode going off. To restore the output power, cut off the output load
for approximately 1 minute.
In case of of the short-circuit to the AUX, BAT output, or incorrect connection of the battery, the fuse FBAT in
the battery circuit becomes permanently damaged and the restoration of the voltage at the BAT output requires the
replacement of the fuse.
4.2 Running the PSU module from the battery.
The power supply module is equipped with the button on the PCB allowing to run the PSU from the battery,
when needed. To do that, press and hold the START button on the unit board for 1 second.
4.3 Deep discharge battery protection UVP.
The power supply is equipped with deep discharge battery protection (UVP). If the voltage at the battery
terminals drops below 20V±0.5V during battery-assisted operation, the batteries will be disconnected. The battery
protection is on when the PBAT jumper is off.
Caution.
It is not recommended to disable UVP since deep discharge of the batteries reduces their ability to
store energy, their capacity and lifetime.
4.4 Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU module from the
power supply network. The PSU module does not require performing any specific maintenance measures, however, in
the case of significant dust rate, its interior is recommended to be cleaned with compressed air. In case of fuse
replacement, use a replacement of the same parameters.

www.pulsar.pl MSRK3024
8
WEEE MARK
According to the EU WEE Directive –It is required not to dispose of electric or electronic waste as
unsorted municipal waste and to collect such WEEE separately.
The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but recycled
according to the applicable law.
THE GENERAL WARRANTY CONDITIONS
1. Pulsar (the manufacturer) grants a five-years warranty for the equipment, counted from the device’s production date.
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the
manufacturer’s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects, unless such
defects have been reported within the warranty period (item 1).
3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the
manufacturer.
4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.
5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenienve, however not
later that within 14 days from the delivery to the service centre of the manufacturer.
6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the
equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.
7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.
8. The warranty does not cover the defects of the equipment, resulting from:
- reasons beyond the manufacturer's control,
- mechanical damage,
- improper storage and transport,
- use that violates the operation manual or equipment’s intended use
- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,
- improper installation and configuration (in defiance with the manual),
9. The warranty is void in any of the following circumstances:
- construction changes
- repairs carried out by any unauthorized service center
- damage or removal of warranty labels
- modifications of the serial number
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the
wholesale prices suggested by the manufacturer on the day of purchase.
11. The manufacturer takes no reponsibility for the defects that result from:
- the damaging, malfunctioning or inability to operate the equipment
- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the
recommendations and requirements contained in the manual, or the use of the equipment.
Pulsar
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [email protected], [email protected]
http:// www.pulsar.pl, www.zasilacze.pl