PureLink HTE Tx User manual

HTE Owner’s Manual
HDMI, RS-232, IR & Ethernet Extender
over HDBaseT with 3D, 4K, POE Support
HTE Tx HTE Rx
PureLinkTM
535 East Crescent Ave
Ramsey, NJ 07446
Tel: [phone]
Fax: [phone]
Website : www.purelinkav.com
E-mail : [e-mail]
For Technical Support, contact us at
: [email protected]

PureLink by Dtrovision
2
Package Contents
Please make sure all of the following items are included in the package:
1 x HTE Transmitter Module
1 x HTE Receiver Module
1 x Power adapter
1 x User Manual
Description
The PureLink HTE is a transmitter and receiver set for long distance extension of HDMI
video and embedded audio with bi-directional control signals ( RS-232 and IR) over
single CAT 5/6/7- type cable. It is designed on HDBaseT technology which allows full 3D
support with up to 330ft (100m) at 4K2K (UHD) resolution. A compact and low profile
enclosure makes the HTE ideal for extending HDMI video, embedded multi-channel
audio, bi-directional control signal, and Ethernet to limited space environment such as
behind a flat-panel display.
PureLink HTE is HDCP compliant and it enables the reliable, long distance extension of
HDMI signals, supporting Deep Color and full 3D and embedded HD lossless audio
formats. In addition, EDID and HDCP communication is being maintained between a
source and display. Also, the HTE includes an RS-232 and IR insertion port, allowing bi-
directional control of an AV device.
Features
Zero loss & Zero noise delivery of digital high definition video and audio signal
using UTP connection, HTE delivers HD signals over CAT5/6/7-type cables
without loss or digital interference maintaining the clarity and colors. Noise
cancellation and error correction logic enhances HDMI video and audio signals
over long distance.
Compact and Robust enclosure design allows for discreet installation behind a
flat-panel display.
Designed based on HDBaseT Technology, supporting support Deep Color and
full 3D support plus DTS-HD and Dolby TrueHD over a single low cost CATx
interface with up to 330ft (100m) at Ultra HD (4K) or 1920x1200 resolution.
Uncompressed high definition video up to 4K2K@30Hz@48bits and 3D.
Controls signals including bi-directional RS-232 and IR function.

PureLink by Dtrovision
3
Bi-Directional RS232 interface –commands and data can flow in both directions
via RS232, allowing status requests and control of the destination unit.
Max. Data Rate- 10.2 Gbps.
HDCP (High-bandwidth Digital Content Protection) Support.
HDMI version 1.4 Support.
Audio transmission support LPCM 7.1@192KHz, Dolby TrueHD, DTS-HD MA.
Support 10/100Mbps network, allow to connect the network TV or another
internet devices.
Support POE, only requires power on the transmitter
Model
HTE
Input Signal
HDMI
Output Signal
HDMI
Supporting Display
Resolutions
VGA ~ WUXGA (up to 1920 x 1200 @ 60Hz),
480i ~ 1080p, Ultra HD (4K) @ 30Hz
Max. Distance
1920x1200 @ 60Hz or
Ultra HD (4K) @30Hz: 330ft (100m)
Connector Type
DC Power Jack
HDMI 19 Pin Female (Type A)
RJ-45
IR
Serial
Conformations
HDMI version 1.4 With HDCP
Power Rating
DC 24V , 1A
Dimension (WxDxH)
Tx: 3.5’’ x 5.3’’ x 1.2’’ (88 x 135 x 30 mm)
Rx: 3.5’’ x 5.3’’ x 1.2’’ (88 x 135 x 30 mm)
Weight
Tx: 0.66 lbs (0.3 kg)
Rx: 0.66 lbs (0.3 kg)
*Please use CAT6a/CAT7 cable for maximum distance transmission.

PureLink by Dtrovision
4
* Travel Range Specification
Cable Type
Range
Pixel clock rate
Video Data Rate
Supported Video
CAT5e/CAT6
100 m
<= 225 MHz
<= 5.3 Gbps
(HD Video)
Up to 1080p, 60Hz, 36bpp (Data
rates lower than 5.3 Gbps or
below 225 MHz TMDS clock)
70 m
> 225 MHz
> 5.3 Gbps
(Ultra HD Video)
1080p 60Hz 48bpp, 1080p60Hz
3D, and Ultra HD (4K) @ 30Hz
CAT6a/CAT7
100 m
> 225 MHz
> 5.3 Gbps
(Ultra HD Video)
1080p 60Hz 48bpp, 1080p60Hz
3D, and Ultra HD (4K) @ 30Hz
Operation and Reliability Specification
1. Operating Environment
Temperature : 32F ~ 131F (0℃~ 55℃)
Humidity : 10% ~ 80%
Altitude : 3,000m Max.
2. Transit Environment
Temperature : -13F ~ 140F (-25℃~ 60℃)
Humidity : 5% ~ 95%
Altitude : 15,000m Max.
3. Storage Environment
Temperature : -4F ~ 185F (-20℃~ 85℃)
Humidity : 5% ~ 95%
Altitude : 3,000m Max.
4. Reliability
MTBF: 90% at over 50,000 hours aging test
In compliance with LCD Monitor reliability test standard

PureLink by Dtrovision
5
Installation and Connection Instructions
1. Turn off both the video source and the display before connecting any cables.
2. Connect CATx cable between the HTE transmitter and the HTE receiver.
3. Connect HDMI cable between the source and the HTE transmitter AND the HTE
receiver and the display.
4. Connect the power supply unit to HTE transmitter module.
(HTE receiver receives power from HTE transmitter)
5. Turn on Display.
6. Turn on Video Source.
How to terminate CATx cable
HTE was designed to conform to TIA/EIA-568-B standard. Please ensure that each PIN
layout of HTE transmitter and HTE receiver are corresponding with the picture below
before connecting the cable. Please note that CAT5e or above level cable enables to
deliver better video quality and longer distance.
For HDBaseT 
For 10/100Mbps Ethernet 
Pin
TIA/EIA-568B
Wire color
Digital RGB
1
Orange/ White
DATA0 +
2
Orange
DATA0 -
3
Green/ White
DATA1
4
Blue
DATA2 +
5
Blue/ White
DATA2
6
Green
DATA1 -
7
Brown/ White
DATA3
8
Brown
DATA3 -
Pin
TIA/EIA-568B
Wire color
Digital RGB
1
Orange/ White
RX +
2
Orange
RX -
3
Green/ White
TX +
4
Blue
N/C
5
Blue/ White
N/C
6
Green
TX -
7
Brown/ White
N/C
8
Brown
N/C

PureLink by Dtrovision
6
CATx cable
Link cable recommend use high quality CAT5, CAT5e, CAT6, CAT6a, CAT7 UTP / STP or
FTP cable.
Transmission Distance
The maximum transmission distance up to 100meters, use lower resolution won’t
extend longer distance
If connection through the wall socket, the cable length must less 5 meters between
HDMI extender and wall jack, as below drawing:

PureLink by Dtrovision
7
HTE Transmitter Specification
Transmitter Module Dimensions (W x D x H): 3.5’’ x 5.3’’ x 1.2’’ (88 x 135 x 30 mm)
Transmitter Module Weight : 0.66 lbs (0.3 kg)
Connection Ports:
HDMI IN: HDMI input
Green LED: Power On/Off Indication
Blue LED: IR receive
Red LED: IR transmit
IR Tx : IR output
IR Rx : IR input
RS232 : Bi-directional serial communication port
DC 24V :Power supply unit Input
RJ-45(CATx) : 2 x Ethernet
1 x HDBaseT output

PureLink by Dtrovision
8
HTE Receiver Specification
Receiver Module Dimensions (W x D x H): 3.5’’ x 5.3’’ x 1.2’’ (88 x 135 x 30 mm)
Receiver Module Weight : 0.66 lbs (0.3 kg)
Connection Ports:
HDMI OUT: HDMI output
Green LED: Power On/Off Indication
Blue LED: IR receive
Red LED: IR transmit
IR Tx : IR output
IR Rx : IR input
RS232 : Bi-directional serial communication port
RJ-45(CATx) : 2 x Ethernet
1 x HDBaseT output

PureLink by Dtrovision
9
LED Indication:
IR Status:
Color
LED Function
HTE Tx
HTE Rx
GREEN
Power
On: power on
BLUE
IR Receive
On: IR received signal
RED
IR Emit
On: IR emitting
HTBaseT Status:
Color
LED Function
HTE Tx
HTE Rx
GREEN
HDBaseT Linking
On: HDBaseT linking
BLUE
Reserve
No Function
RED
HDCP
On: with HDCP / Flash: Without HDCP / Off: HDMI
disconnect
10/100 Ethernet Port:
Color
LED Function
HTE Tx
HTE Rx
GREEN
Ethernet linking
On: Linking /Flash: data transmission
YELLOW
Reserve
No Function
Low Power Mode:
When there is no HDMI video signal input, or TV is not connected or power off, HTE
will enter a low-power mode to save power consumption. When it is on a low
power mode, it still provides Ethernet, RS-232, IR, and CEC signal transmission.
Caution:
1. The wiring must away from any equipment with electromagnetic wave, i.e.:
mobile phone, microwave, radio equipment, fluorescent lamp, high voltage
power lines.
2. This device is not a network equipment, do not connect with Network to avoid
damage.
3. IR transmitter do not put near from receiver to avoid mutual interference.

PureLink by Dtrovision
10
Technical Specification
Frequency Range: 25 ~ 165 MHz
Supporting Resolutions: Up to 1080p / 60Hz / 48 bit
Up to Ultra HD (4K) / 30Hz
Up to 1920x1200 / 60Hz
I/O Signal Standard: HDMI 1.4
Max Distance: Max 330ft (100m) at 4K2K@30Hz /
1920x1200@60Hz
RS-232 Connector: Transmitter: DB9 Female
Receiver: DB9 male
RS-232 Baud Rate: Up to 115200 bps / Full Duplex
IR Carrier: 38Khz / ±10°/ 5M / 2 Way
UTP Cable specification: CAT5/5e/6/6a/7
Ethernet Connector: RJ-45 with 2 LED
Ethernet Data Rate: 10 / 100Mbps
Ethernet Distance: Max 330ft (100m)
Input Ports: HDMI Female 19P (Type A) / RJ-45
Output Ports: HDMI Female 19P (Type A) / RJ-45
Power Consumption: Min Total 5W,
Max Total 15W
Power Rating: 24V DC / 1A
Weight: Transmitter –0.66 lbs (0.3 kg)
Receiver –0.66 lbs (0.3 kg)

PureLink by Dtrovision
11
Warranty
One (1) Year Warranty
Dtrovision warrants this HDMI, RS-232, IR, and Ethernet Extender over CATx with 3D, 4K,
POE Support to be free from defects in workmanship and materials, under normal use
and service, for a period of one (1) year from the date of purchase from Dtrovision or its
authorized resellers.
If a product does not work as warranted during the applicable warranty period,
Dtrovision shall, at its option and expense, repair the defective product or part, deliver
to customer an equivalent product or part to replace the defective item, or refund to
customer the purchase price paid for the defective product.
All products that are replaced will become the property of Dtrovision.
Replacement products may be new or reconditioned.
Dtrovision shall not be responsible for any software, firmware, information, or memory
data of customer contained in, stored on, or integrated with any products returned to
Dtrovision for repair under warranty or not.
Warranty Limitation and Exclusion
Dtrovision shall have no further obligation under the foregoing limited warranty if the
product has been damaged due to abuse, misuse, neglect, accident, unusual physical or
electrical stress, unauthorized modifications, tampering, alterations, or service other
than by Dtrovision or its authorized agents, causes other than from ordinary use or
failure to properly use the Product in the application for which said Product is intended.

PureLink by Dtrovision
12
FCC/CE Statement
This device complies with part 15 of FCC Rules and EN 55022/55024/61000-3 for CE
certification. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must not accept any interference
received, including interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 and 2 of FCC Rules and EN 55022/55024/61000-3 for CE
certification. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and. if not installed
and used in accordance with the instruction guide, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult a service representative for help.
Properly shielded and grounded cables and connectors must be used in order to comply
with FCC/CE emission limits. Changes or modifications not expressly approved by the
party responsible for compliance could void the user s authority to operate the
equipment.