PureLink DTE RX User manual

DTE Owner’s Manual
DVI, RS-232 and IR Extender over
HDBaseT w/POE
PureLinkTM
535 East Crescent Ave
Ramsey, NJ 07446
Tel: [phone]
Fax: [phone]
Website : www.purelinkav.com
E-mail : [e-mail]
For Technical Support, contact us at
: [email protected]

Package Contents
Please make sure all of the following items are included in the package:
1 x Transmitter Module
1 x DTE Receiver Module
1 x Power adapter DC 48V
1 x User Manual
1 x IR Blaster Cable (Peak wavelength 940nm)
1 x IR Receiver cable
4 x Screws
8 x Foot pads
Description
The PureLink DTE is a transmitter and receiver set for long distance extension of DVI
video and embedded audio (if supported) with bi-directional control signals ( RS-232
and IR) over single CAT 5/6/7- type cable. It is designed on HDBaseT technology which
can extend the signals up to 330ft (100m) at 1080p@60Hz or 1920x1200@60Hz
resolution with POE. A compact and low profile enclosure makes the DTE ideal for
extending DTE video, embedded audio (if supported), and bi-directional control signal to
limited space environment such as behind a flat-panel display.
PureLink DTE is HDCP compliant and it enables the reliable, long distance extension of
DVI signals, supporting Deep Color and full 3D and embedded HD lossless audio formats.
In addition, EDID and HDCP communication is being maintained between a source and
display. Also, the DTE includes an RS-232 and IR insertion port, allowing bi-directional
control of an AV device.
Features
Zero loss & Zero noise delivery of digital high definition video and audio signal
using UTP connection, DTE delivers HD signals over CAT5/6/7-type cables
without loss or digital interference maintaining the clarity and colors. Noise
cancellation and error correction logic enhances HD video and audio signals over
long distance.
Compact and Robust enclosure design allows for discreet installation behind a
flat-panel display.
Designed based on HDBaseT Technology, supporting support Deep Color and
full 3D support over a single low cost CATx interface with up to 330ft (100m) at

PureLink by Dtrovision
3
1080p or 1920x1200 resolution.
Controls signals including bi-directional RS-232 and IR function.
Bi-Directional RS232 interface –commands and data can flow in both directions
via RS232, allowing status requests and control of the destination unit.
Max. Data Rate- 10.2 Gbps.
HDCP (High-bandwidth Digital Content Protection) Support.
DVI verion 1.0 support
LED signal indicator
Product application note
Figure 1 –Schematic Connection Diagram of DTE Tx/Rx
Product Specification
Transmitter

PureLink by Dtrovision
4
Model
DTE Tx
Input type
DVI, 1 port
RS232, 1 port (bi-direction)
Output type
CATx (HDBaseT), 1 port
IR, 1 port
Supporting Display
Resolutions
VGA ~ WUXGA (up to 1920 x 1200 @ 60Hz),
480i ~ 1080p
Max. Distance
1920x1200 @ 60Hz or
1080p @60Hz: 330ft (100m)
Connector Type
DC Power Jack
DVI Female
RJ-45
IR
Serial
Conformations
DVI version 1.0 With HDCP
Power Rating
DC 48V, 1.05A
Dimension (WxDxH)
5.90’’ x 3.15’’ x 1.38’’ (150 x 80 x 35 mm)
Weight
0.73 lbs (0.33 kg)
Receiver

PureLink by Dtrovision
5
Model
DTE Rx
Input type
CATx (HDBaseT), 1 port
IR, 1 port
Output type
DVI, 1 port
RS232, 1 port (bi-direction)
Supporting Display
Resolutions
VGA ~ WUXGA (up to 1920 x 1200 @ 60Hz),
480i ~ 1080p
Max. Distance
1920x1200 @ 60Hz or
1080p @60Hz: 330ft (100m)
Connector Type
DC Power Jack
DVI Female
RJ-45
IR
Serial
Conformations
DVI version 1.0 With HDCP
Power Rating
DC 5V , 2A
Dimension (WxDxH)
5.90’’ x 3.15’’ x 1.38’’ (150 x 80 x 35 mm)
Weight
0.73 lbs (0.33 kg)
*Please use CAT6a/CAT7 cable for maximum distance transmission.

PureLink by Dtrovision
6
Operation and Reliability Specification
1. Operating Environment
Temperature : 32F ~ 131F (0℃~ 55℃)
Humidity : 10% ~ 80%
Altitude : 3,000m Max.
2. Transit Environment
Temperature : -13F ~ 140F (-25℃~ 60℃)
Humidity : 5% ~ 95%
Altitude : 15,000m Max.
3. Storage Environment
Temperature : -4F ~ 185F (-20℃~ 85℃)
Humidity : 5% ~ 95%
Altitude : 3,000m Max.
4. Reliability
MTBF: 90% at over 50,000 hours aging test
In compliance with LCD Monitor reliability test standard

PureLink by Dtrovision
7
Installation and Connection Instructions
1. Turn off both the video source and the display before connecting any cables.
2. Connect CATx cable between the DTE transmitter and the DTE receiver.
3. Connect DVI cable between the source and the DTE transmitter AND the DTE
receiver and the display.
4. Connect the power supply unit to DTE transmitter and DTE receiver module.
5. Turn on Display.
6. Turn on Video Source.
How to terminate CATx cable
DTE was designed to conform to TIA/EIA-568-B standard. Please ensure that each PIN
layout of DTE transmitter and DTE receiver are corresponding with the picture below
before connecting the cable. Please note that CAT5e or above level cable enables to
deliver better video quality and longer distance.
For HDBaseT 
For 10/100Mbps Ethernet 
Pin
TIA/EIA-568B
Wire color
Digital RGB
1
Orange/ White
DATA0 +
2
Orange
DATA0 -
3
Green/ White
DATA1
4
Blue
DATA2 +
5
Blue/ White
DATA2
6
Green
DATA1 -
7
Brown/ White
DATA3
8
Brown
DATA3 -
Pin
TIA/EIA-568B
Wire color
Digital RGB
1
Orange/ White
RX +
2
Orange
RX -
3
Green/ White
TX +
4
Blue
N/C
5
Blue/ White
N/C
6
Green
TX -
7
Brown/ White
N/C
8
Brown
N/C

PureLink by Dtrovision
8
CATx cable
Link cable recommend use high quality CAT5, CAT5e, CAT6, CAT6a, CAT7 UTP / STP or
FTP cable.
Transmission Distance
The maximum transmission distance up to 100meters, use lower resolution won’t
extend longer distance
If connection through the wall socket, the cable length must less 5 meters between DVI
extender and wall jack, as below drawing:
IR Receiver Cable Directions:
Put it into the DTE Rx IR IN port and place the IR receiver cable, so that you can point to
it easily with your IR remote controller
IR Blaster Cable Directions:
Plug IR blaster cable plug into DTE Tx IR OUT port, it sits in front of the device receiver’s
IR sensor, which is located on the front panel.
IR cable pin out

PureLink by Dtrovision
9
RS-232/Serial pin out
Caution:
The CATx wiring must be away from any elecromagnetic wave equipment, i.e :
mobile phone, microwave, radio, fluorescent lamp, high voltage power lines.
Do not place IR transmitter near from IR receiver to avoid mutual interference

PureLink by Dtrovision
10
Chapter 3. Additional Information
3.1 Manufacturer’s Warranty (3 Years)
PureLink warrants this DTE HDBaseT extender to be free from defects in
workmanship and materials, under normal use and service, for a period of three (3)
year from the date of purchase from PureLink or its authorized resellers.
If the product does not operate as warranted during the applicable warranty period,
PureLink shall, at its option and expense, execute one of the following as necessary:
1. Repair the defective product or part
2. Deliver to customer and equivalent product or part to replace the defective
item
3. Refund to customer the purchase price paid for the defective product
All products that are replaced become the property of PureLink. Replacement
products may be new or reconditioned. Repaired or replacement products or parts
come with a 90-day warranty or the remainder of the warranty period. PureLink
shall not be responsible for any software, firmware, information, or memory data
loss of contained in, stored on, or integrated with any products returned to PureLink
for repair under warranty.
3.2 Customer Service
Any customer service inquiries can be submitted electronically through the Q&A
form on our website ( www.purelinkav.com ).
For immediate assistance please contact us at [phone] to reach our customer
care or tech support team.