PureLink WHD100T User manual

WHD100T/R (WHD030-V2)
User Manual | Benutzerhandbuch
V2 | 2017-11

- 2 -
DEUTSCH
Appendix - supported Resolutions
Anhang - Unterstützte Auösungen
11 - 17
19
ENGLISH03 - 09

- 3 - ENGLISH
TABLE OF CONTENT
1. INTRODUCTION ............................................................................................................................................................................ 4
2. INTENDED USE ............................................................................................................................................................................ 4
3. INTENDED COUNTRIES .................................................................................................................................................................. 4
4. SAFETY INSTRUCTIONS ................................................................................................................................................................ 4
5. PACKAGE CONTENT....................................................................................................................................................................... 5
6. INSTALLATION............................................................................................................................................................................... 5
6.1 The PureLink WHD030-V2 Transmitter (TX) ....................................................................................................................................................................................5
6.2 The PureLink WHD030-V2 Receiver (RX) .........................................................................................................................................................................................6
7. USAGE .......................................................................................................................................................................................... 6
7.1 Switch the PureLink WHD030-V2 ON................................................................................................................................................................................................6
7.2 Switch your equipment ON..................................................................................................................................................................................................................6
7.3 Standby mode.........................................................................................................................................................................................................................................6
8. FREQUENTLY ASKED QUESTIONS .................................................................................................................................................. 7
No connection................................................................................................................................................................................................................................................7
No signal available from chosen source..................................................................................................................................................................................................7
Video resolution is not supported............................................................................................................................................................................................................7
Laptop or PC settings ...................................................................................................................................................................................................................................7
9. TECHNICAL DATA .......................................................................................................................................................................... 8
Resolutions.....................................................................................................................................................................................................................................................8
Wireless...........................................................................................................................................................................................................................................................8
Transmitter (TX) .............................................................................................................................................................................................................................................8
Receiver (RX) ..................................................................................................................................................................................................................................................8
Power supply..................................................................................................................................................................................................................................................8
Frequency Band & max. RF Power.............................................................................................................................................................................................................8
Transmitter......................................................................................................................................................................................................................................................8
Receiver...........................................................................................................................................................................................................................................................8
10. CLEANING .................................................................................................................................................................................... 8
11. MAINTENANCE ............................................................................................................................................................................ 9
12. WARRANTY AND LIABILITY .......................................................................................................................................................... 9
13. CE CONFORMITY ........................................................................................................................................................................... 9
14. DISPOSAL OF THE DEVICE............................................................................................................................................................. 9
15. DISCLAIMER ................................................................................................................................................................................ 9
16. APPENDIX - SUPPORTED RESOLUTIONS ...................................................................................................................................... 19

- 4 -
1. INTRODUCTION
Congratulations on your purchase of the PureLink WHD030-V2! Replace your HDMI cable wirelessly and locate your HDTV
or projector wherever you want in the same room. No need to worry about the location of your HD equipment. Perfect if
you would rather not see cables running across the walls or if you do not want to (or cannot) drill holes and lay cables.
Suitable for all HDMI equipment, such as Blu-ray®, HD set-top box or Laptop.
PureLink products are manufactured with the utmost precision and are top quality. Please read this manual carefully and
follow the instructions in order to get the very best from this product.
2. INTENDED USE
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product for
purposes other than those described above, the product may be damaged. In addition, improper use can cause hazards
such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only together with its operating
instructions.
3. INTENDED COUNTRIES
Germany
Austria
4. SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety
instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury
or damage to property. Such cases will invalidate the warranty/guarantee.
The device is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly. These may become dangerous playing material for children.
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture, flammable gases,
vapors and solvents.
Do not place the product under any mechanical stress.
If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe
operation can no longer be guaranteed if the product:
· is visibly damaged,
· is no longer working properly,
· has been stored for an extended period in poor ambient conditions or
· has been subjected to any serious transport-related stresses.
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
Also observe the safety and operating instructions of any other devices which are connected to the product.
Consult an expert when in doubt about the operation, safety or connection of the device.
Make sure to observe the polarity and magnitude of the output voltage. Incorrect polarity or excessive voltage input
leads to the destruction of the connected electrical appliance.
Sufficient ventilation is essential when operating the product. Do not cover the product. Never place the product on a
table cloth or on a carpet! Place it on a hard, flame resistant base.

The product should not be used immediately after it has been brought from an area of cold temperature to an area
of warm temperature. Condensed water might destroy the product. Wait until the product adapts to the new ambient
temperature before use.
Make sure that the output of the power adapter is not short-circuited.
Suffocation Risk! Keep packaging materials away from children!
5. PACKAGE CONTENT
1x PureLink WHD030-V2 Transmitter (TX, WHD100T)
1x PureLink WHD030-V2 Receiver (RX, WHD100R)
2x Energy-saving switch mode power adapter
1x HDMI cable 1.5 m
1x Mini USB cable
1x Plugs + screws
1x User Manual
6. INSTALLATION
6.1 THE PURELINK WHD030-V2 TRANSMITTER (TX)
1. Connect your WHD030-V2 transmitter to your HD device (HDMI OUT) or laptop (HDMI OUT).
2. Connect the power adapter to the USB port on the WHD030-V2 transmitter and to a socket.If your HD device or Laptop
has a USB port you can also use the USB cable to power the WHD030-V2 transmitter.
ENGLISH
- 5 -

- 6 -
6.2 THE PURELINK WHD030-V2 RECEIVER (RX)
1. Connect your HDTV or HD Projector (HDMI IN) via an HDMI cable to the WHD030-V2 Receiver (HDMI OUT).
2. Connect the power adapter to the USB IN on the WHD030-V2 Receiver and to an electrical socket.
Note: Use the 2 plugs and 2 screws if you wish to attach the WHD030-V2 Receiver to the wall (e.g. behind your HDTV).
7. USAGE
7.1 SWITCH THE PURELINK WHD030-V2 ON
1. Once both power adapters have been inserted into the socket, the PureLink WHD030-V2 transmitter and receiver will
switch on automatically.
2. While warming up, both power LEDs will flash blue until the signal connection between the transmitter and receiver
has been established. It takes about 80 seconds for the system to start up.
3. If there is a good connection between the transmitter and receiver, both LEDs will light up and remain blue.
Note: Place the transmitter and receiver at least 1 meter apart to ensure a good connection.
7.2 SWITCH YOUR EQUIPMENT ON
1. Switch the HDTV or HD Projector ON and select the HDMI input on this device to which you have connected the
PureLink WHD030-V2 Receiver.
2. Switch the HD device or Laptop to which the PureLink WHD030-V2 transmitter is connected ON.
3. If there is a good connection between your HD device and the HDTV (or HD Projector), both LEDs on the receiver will
light up in blue constantly (see table in the event of another situation).
7.3 STANDBY MODE
If the power supply to the PureLink WHD030-V2 Transmitter is interrupted (power adapter or USB power cable), the
PureLink WHD030-V2 Receiver will switch to Standby mode after 10 minutes. If the PureLink WHD030-V2 Transmitter is
then powered up once again, the receiver will automatically detect this and switch back ON.

ENGLISH
- 7 -
Mode Status description Power LED
receiver
Status LED
receiver
Display on
HDTV / projector
Standby Low power consumption,
all functions are o. Red O
Starting up System is sarting up, this takes
about 80 seconds. Flashes blue Flashes
No connection
If the system is not able to make a
connection for 80 seconds during
start-up, it continues to search for
available channels.
Flashes blue Flashes
Connected
No input signal available from
chosen source. Blue Flashes 3x per second
Video resolution is not supported. Blue Flashes 1x per second
Video resolution is recognised
and connection between transmit-
ter and receiver is stable.
Blue Blue
Audio and video will be
reproduced on your HDTV /
projector
8. FREQUENTLY ASKED QUESTIONS
NO CONNECTION
If the PureLink WHD030-V2 is not able to make a stable connection for 80 seconds during start-up, the PureLink
WHD030-V2 Receiver is probably outside the range of the PureLink WHD030-V2 Transmitter. Place them closer to each
other (a minimum distance of 1 meters apart) and check whether the connection can be made.
NO SIGNAL AVAILABLE FROM CHOSEN SOURCE
The PureLink WHD030-V2 does not recognize an input signal on the selected SOURCE.
• Check whether the correct HDMI source has been selected and whether this is ON.
• Check whether the HDMI cable between the PureLink WHD030-V2 Transmitter and HD device is connected properly.
• Replace the HDMI cable to the HD device.
VIDEO RESOLUTION IS NOT SUPPORTED
The video resolution that is set on your HD device is not recognized by the PureLink WHD030-V2 Transmitter.
• Connect the HD device directly to the HDTV or projector and check whether the set video resolution corresponds to
the resolutions that are supported.
LAPTOP OR PC SETTINGS
• Consult your Laptop or PC instructions for the correct picture and audio settings.
• Check to ensure that the resolution set corresponds to the resolutions that are supported.
Do you have other questions that have not been resolved by the above information?
Please contact us on www.purelink.de/en/service/support/

- 8 -
9. TECHNICAL DATA
RESOLUTIONS
Supported HDTV resolution (HDMI) 480p, 576p, 720p, 1080i, 1080p
Supported PC resolution (max.) 1600x1200 px
Supported 3D formats 1080p @23.98/24 Hz, 720p @59.94/60/50 Hz
Supported audio formats (digital) Up to 6 Mbps AC-3 and DTS
WIRELESS
Operational frequency 4.9 - 5.9 GHz
Operational range Up to 10 meters LOS (line of sight)
System latency No latency (<1ms)
TRANSMITTER (TX)
HDMI input 1x HDMI-A (19-pin female)
Dimensions 30 x 82.2 x 17.5 mm
RECEIVER (RX)
HDMI output 1x HDMI-A (19-pin female)
Dimensions 194.8 x 146.8 x 31 mm
POWER SUPPLY
Switch mode power adapter 100-240VAC @ 50-60Hz, 5VDC 1.5A
Specifications may be modified without prior notice.
FREQUENCY BAND & MAX. RF POWER
TRANSMITTER
5180-5240MHz: 8.29dBm
5260-5350MHz: 8.29dBm
5500-5700MHz: 8.66dBm
RECEIVER
5180-5240MHz: 22.03dBm
5260-5350MHz: 22.88dBm
5500-5700MHz: 22.04dBm
10.CLEANING
Before cleaning the product must be disconnected from mains socket and all electrical loads.
Only use dry and soft cloth to clear the housing of the Product.
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause damage to the
housing and malfunctioning.
To clean the product, a dry, soft and clean cloth is sufficient. Do not apply too much pressure to the housing as this may
cause scratch marks.

ENGLISH
- 9 -
11.MAINTENANCE
There are no components located inside the product you need to maintain. Never open/dismantle the product.
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.
If you have questions which remain unanswered by these operating instructions, contact our technical support service or
other technical personnel.
12.WARRANTY AND LIABILITY
The producer grants 2 years warranty to a new device.
As the manufacturer has no influence on installation, warranty only applies to the product itself.
If any fault or damage is detected on your product, please contact your dealer and provide your sales slip or invoice
as evidence of the purchase, if necessary. Your dealer will repair the fault either on site, or send the device to the
manufacturer. You make the work of our technicians considerably easier, describing possible faults in detail – only then
you can be assured that faults, occurring only rarely, will be found and repaired with certainty!
The manufacturer is not liable for damages to persons or property caused by improper installation, operation or
maintenance, not described in this manual.
Do not alter or modify the product or its accessories.
Any use other than described in this user`s manual is not permitted and causes loss of warranty, loss of guarantee, and
non-liability.
13.CE CONFORMITY
PureLink GmbH hereby declares that the PureLink WHD030-V2 radio communication system complies with
Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet address:
www.purelink.de/ce/4260134125208_CE.pdf
14.DISPOSAL OF THE DEVICE
WEEE-Reg. No.: DE 93847290
According to the European WEEE directive, any electrical and electronic equipment must not be disposed with consumers
waste. As a consumer, you are committed by law to reposit electrical and electronic devices to public collecting points or
to the dealer for free at the end of the device’s lifetime. Details are regulated in the respective national legislations. The
garbage can symbol on the product, in the manual or on the packaging refers to these terms. With the return of your used
devices you actively take part in protecting the environment.
15.DISCLAIMER
This product complies with the statutory national and European requirements. All company names and product names
are trademarks of their respective owners.
All rights reserved.
We reserve our right for misprints and changes of the device, packing or user`s manual.
HDMI®is a registered trademark of HDMI Licensing L.L.C.

- 10 -