Pyle Pro PDWM5300 User manual

OPERATION MANUALOPERATION MANUAL
PDWM5300
UHF PLL Diversity Wireless
Microphone System w/ LCD
UHF PLL Diversity Wireless
Microphone System w/ LCD
PDWM 5300
UHF PLL Diversity Wireless
Microphone System w/ LCD
UHF PLL Diversity Wireless
Microphone System w/ LCD
PDWM 5300
OPERATION MANUALOPERATION MANUAL
PDWM5300

1
Precautions
Hand-held microphone
Receiver
Installation
Trouble shooting
Specifications
Thank you for buying the PDWM5300 Wireless System. Please
read through these operation instructions so you will know how
to operate your model properly. After you read it, put it away in a
safe place for future reference.
Avoid exposure of the system to rain or moisture.
No user-serviceable parts inside the system. Refer all servicing to a qualified
technician only.
Handle the wireless system carefully, dropping or other shocks may cause
failure.
Avoid using the system where it may be subjected to heat, such as direct sunlight,
near radiators or other heat sources.
Should any liquid be spilt on the system, stop using it immediately. It may be
possible to dry the system, but you should have it checked by a qualified technician
before using it again.
Take care with the main power adapter and lead. If damaged in any way, do not use
the system and refer to a qualified technician for repair.
Only use the system with the supplied components. Do not attempt to use with any
other main power supply adapter .
If the is not going to be used for a while, remove the battery to
prevent leakage. In the event of electrolyte leakage inside the battery compartment,
carefully remove the leakage with a damp cloth. Take care not to get battery
electrolyte in contact with your skin, however if it does, wash your hands under a
running tap. If electrolyte comes into contact with your eyes, seek medical advice
immediately.
Only replace the battery with the same or an equivalent type.
Please dispose of old batteries in an environmentally friendly manner in accordance
with the relevant legislation.
Do not use any solvents to clean any part of the .
wireless system
wireless system

2
+
-
+
-
7
6
ON
OFF
1234
ON DIP
CH11
801.8MHz
CH03
797.0MHz
CH09
800.6MHz
CH01
795.8MHz
CH10
801.2MHz
CH02
796.4MHz
CH07
799.4MHz
CH05
798.2MHz
CH06
798.8MHz
CH04
797.6MHz
CH08
800.0MHz
CH00
795.2MHz
CH12
802.4MHz
CH13
803.0MHz
CH14
803.6MHz
CH15
804.2MHz
FREQUENCY CHART
1. Unscrew the battery cover at the end of the microphone. Install the
provided 2 1.5V batteries, taking care to fit it with the correct polarity
connected.
2. According to frequency Chart on the battery cover, adjust the CH
selector to make the microphone to be the same frequency as receiver.
3. Check the battery by switching the microphone ON. The red LED will
come on. This indicates correct operation. If the red LED is dim, this
indicates the battery is low and should be changed. If the red LED does
not come on at all, it indicates the battery is dead and should be replaced.
PARTS DESCRIPTION
OPERATION
1. Mesh: cartridgeinside
2. Tube
3. Power LEDindicator
4. Power andMute switch: Switchon and off the microphone.
Move the switchto middle positionto mute themic.
5. Battery compartment
6. Battery Cover
7. CH selector

3
1.
2. Insert one end of included audio cable into AF OUT on rear panel,
and the other end into LINE IN of amplifier or mixer.
3. Connect the power adaptor from DC 12V of receiver to a main power socket.
4. Switch on the receiver. The power indicator comes on. LCD display will
illuminate.
Make sure the microphone and receiver to be of same frequency.
5. Switch on the microphone.
W
display on the bottom of LCD display panel.
Connect the antennas A and B. Make sure they are vertical.
""
""
Press
exit.
A letter "A" or "B" will appear in the top right of the
LCD, indicating the diversity reception. RF strength (in dB) is indicated in the
bottom left corner of the display. hen you speak into the microphone, AF
signal will
SET once, there will be a mark displayed on LCD panel.
Now you can adjust frequency by UP/DOWN buttons. Press SET again to
1. Power Switch: Turn on power switch, the display of LCD will illuminate.
2. Power LED indicator: Turn on power switch, this indicator will illuminate.
3. SET: Press once to adjust frequency by UP/DOWN buttons. Press again to exit.
4. UP: Channel UP
5. DOWN: Channel DOWN
6. LCD Display
7. Volume control
8. Antenna Aand B
9. Balanced output
10. Unbalanced output
11. 12V DC IN
PARTS DESCRIPTION
OPERATION
CH00 795.2MHz
00dB AF

4
Using the supplied audio cable, connect from the AF OUT jack socket to the
LINE IN socket on amplifier.
Connect the mains power adaptor from "DC 12V"
jack to a suitable mains power socket.
Alternatively, you can connect an XLR cable to
the XLR balanced output.
Installation Location:
At least 3 ft. above ground level
At Least 3 ft. away from wall
MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE

5
The on air
indicator does
not light up
The wireless microphone is not
turned on. Turn on the wireless microphone
The microphone receiver is not
turned on. Turn on the microphone receiver
and the connected audio equipment
The microphone receiver is not
connected properly.
No sound
The battery in the wireless
microphone is weak. Replace the battery.
The microphone receiver is not
turned on .
Turn on the microphone receiver
and the connected audio equipment.
The connected audio equipment is
not turned on. Turn on the audio equipment.
The speakers/headphones. are not
connected to the audio equipment.
Connect the speakers/
headphones
The sound is
distorted
The battery in the wireless
microphone is weak. Replace the battery.
The AUDIO OUT on the receiver
is not set correctly.
A howling noise
heard from the
speakers.
The distance between the wireless
microphone and speakers are too
close.
Move the wireless microphone
away from the speakers or
change the direction of the
microphone.
The battery in the wireless
microphone is weak Replace the battery.
Adjust the volumecontrols.
Turn on the microphone receiver
and the connected audio equipment
Make sure micand receiver are
set to thesame frequency.
Frequency not setcorrectly.

6
A. Overall System
C
B. Receiver
C. Transmitter
Tr
arrier Frequency: UHF 795~805MHz
Frequency Stabilization: less than 30ppm
Dynamic Range: more than 90dB
Total Harmonic Distortion: less than 0.5%
Frequency Response: 40hz~15khz 3dB
Audio Output Level: separate type:0~ 400mV
Mix Type: 0~ 200mV
Power Supply: DC 12V
Consume Power: 4W
Signal/Noise Ratio: more than 90dB
Image & Spurious Rejection: more than 80dB
Border upon Channel Rejection: more than 80dB
Receiving Sensitivity: 10dBuv(sinad=30dB)
De-emphasis: 50us
ansmitting Power: 8.5mW
Modulation Type : FM,F3F
Max Deviation: 25KHz
Spurious Emission: more than 40dB(with carrier)
Power Supply: 3V