Pyle Pro PDWM9000 User manual

PDWM9000 User’s Manual
CH. A CH.A MIN MIN MAX MAX
RECEIVER LCD
UHF PROFESSIONAL
WIRELESS MICROPHONE
POWE
R
RECEIVER LCD
AF RF
CH 02: 801 . 50MHz
AF RF
CH 02: 801 . 50MHz

1
Thank you for selecting th PLL
Synthesized Diversity System. Before operating please read this
instruction manual carefully and thoroughly in order to understand the
correct operating procedures and achieve the best results.
The PDWM9000 is an UHF wireless
system. Designed for professional applications, it has a 1U rackmount
, balanced XLR and unbalanced 1/4” connections.
e PDWM9000 Dual UHF
advanced PLL synthesized
receiver
This system includes the following accessories:
Audio Output Cable
Antennas (2)
Instruction Manual
AC Power Cable
1. Parts Name and Functions
B. Rear Panel
A. Front Panel
Fig. 1
(3) (5) (3) (5)(4) (4)
CH. A CH.A MIN MIN MAX MAX
RECEIVER LCD
UHF PROFESSIONAL
WIRELESS MICROPHONE
(2)
POWE
R
RECEIVER LCD
(1) (6) (7) (6) (8) (1)(9)
OUT B MIX OUT OUT A DC12
ANT B ANT A
AC:110/220V 50/60Hz
Fig. 2
Introduction
AF RF
CH 02: 801 . 50MHz
AF RF
CH 02: 801 . 50MHz
(1) Antenna Connector
(2) Power Switch & LED Indicator
(3) Channel Selector
(4) LCD Display
(5) Volume Control
(6) Individual Balanced Audio Output Jacks
(7) Mixed Unbalanced Audio Output Jack
(8) DC 12V Power Input Jack
(9) AC Power Input Jack
(10) Voltage Selector
(10)

2
2. Installation of the Receiver
Fig. 3
Connect the AC power cable to the 110/220V AC jack (9) and the other end
into an AC outlet. Check the voltage selector (10) as shown in Fig. 4.
1. Power Connection
2. Audio Output Connection:
(A) 1/4” Unbalanced Output: Connect from the unbalanced
output jack (7) of the receiver the input jack of the amplifier,
as shown in Fig. 3.
(B) XLR Balanced Output: Connect an XLR cable from the balanced
output jack (8) of the receiver to the input jack of the mixer or amplifier,
as shown in Fig.3. There are two individual outputs corresponding to
the two microphones.
a 1/4” cable
to mixer or
This outputs the sound from both microphones
together.
ANT B ANT A
OUT B MIX OUT OUT A DC12 AC: 110V/220V 50/60Hz
Fig. 4
ANT A
DC12 AC: 110/220V 50/60Hz
Fig.5
1:GND
2:HOT
3:COLD
12
3
+

3. Extend antennas A & B. Make them perpendicular with the
machine.
4. Push the power switch to turn on the unit.
5. Adjust the volume using the control knobs on the receiver.
• The receiver should be placed more than 3 ft. above the floor and
3 ft. away from the wall.
• Antennas should be fully extended for best reception.
Receiver Location
3. Parts Name And Function (Microphone)
Fig. 6
CH MHZ
01:08 1.25
1 3 45
2
1. Grill
2. Three position switch (on top).
3. LCD Display
4. Channel Selectors
5. Battery Housing

3
4. Operation of the Microphone
Frequency & Channel Listing
2. Turn on the microphone.
3. The microphone features a three position switch. Place the switch in
Stand By (middle position) to mute the sound without turning off the mic.
1. Screw the battery box cover counter clockwise. Insert a 9v battery
(check the polarity).
Mic B
NO. Frequency Range NO. Frequency Range
790.75MHz 1 801.25MHz
2 791.15MHz 2 801.55MHz
3 791.55MHz 3 801.85MHz
4 791.95MHz 4 802.15MHz
5 792.35MHz 5 802.45MHz
6 792.75MHz 6 802.75MHz
7 793.15MHz 7 803.05MHz
8 793.55MHz 8 803.35MHz
9 793.95MHz 9 803.65MHz
10 794.35MHz 10 803.95MHz
11 794.75MHz 11 804.25MHz
12 795.15MHz 12 804.55MHz
13 795.55MHz 13 804.85MHz
14 795.95MHz 14 805.15MHz
15 796.35MHz 15 805.45MHz
16 796.75MHz 16 805.75MHz
Mic A
1

5
6. Specifications
System Specifications
Carrier Frequency: UHF 790-806MHz
Frequency Stabilization < 30ppm
Dynamic Range: More Than 90dB
Total Harmonic Distortion: Less Than 0.5%
Frequency Response: 40HZ-15KHZ 3dB
Audio Output Level: Unbalanced Out: 0 400mV
......................
........................
............
...................
....................
................ ±
–
–
±
±
Balanced Out: 0 ±200mV
1. Unit does not turn on.
• Make sure the power cable is connected properly.
2. AF display moves, but there is no sound output.
3. The effective receiving distance decreases.
• Check the fuse.
• Check the voltage selector
• Check volume level.
• Check audio cable.
• Check the settings on your amplifier
• Change batteries.
• Check for any devices that may be causing interference.
4. Sound Quality Deteriorates
• Change Batteries.
• Check for any devices that may be causing interference.
• Do not use two machines with the same frequency at the
same time.
Receiver Specifications
Power Supply: AC 11 220V 50 DC12V
Power Consumption: 5 Watts
S/N Ratio: 90 B
Image & Spurious Rejection: 80d
Border Upon Channel Rejection: 80d
Receiving Sensitivty: 10dBuV(SINAD=30dB)
...........................
....................
................................
..........
......
....................
0 60HZ/ HZ or
>d
>B
>B
<
5. Troubleshooting
Caution:
Do not open the unit. There are no user serviceable parts
inside. Refer service to a qualified technician.

6
0dB
60H 14KH
40H 300H 1K 5K 10K 14K 20K 30K
Diagram of AF Frequency Response
Attention:
Microphone Specifications
Transmitter Power: ......
Modulation Type: .......
Max Deviation: .........
Spurious Emission: ......
Battery Voltage: ........
Battery Life: ...........
Noise Control:..........
8.5mW
FM, F3F
+25Khz
>40dB (with carrier)
9V
Approx. 8 Hours
Advanced Noise Reduction Circuitry
1. For best reception, always maintain line of site between the
transmitter and receiver.
2. Avoid direct sunshine or rain and distance the unit as far as
possible from magnetic fields.