Pyle PWPLGU208 User manual

readings prior to the installation of the wall plate to ensure
power has been disconnected.
Do not remove the outlet's wall plate until you are
certain that the outlet is not live. Exposed, live 120 volt AC
devices such as wall outlets and light switches can cause
severe injury, even death.
2. REMOVE THE EXISTING FACE PLATE COVER
Using a at head screwdriver, remove the existing wall
plate. The screw is located directly between the 2 socket of
the outlet. Turn the screwdriver counter-clockwise to
remove the screw. After removing the old wall plate and
you will see the outlet mounted in the electrical box in the
wall, then remove the bottom screw of the outlet.
3. INSTALL USB WALL PLATE CHARGER
Line up the 2 large outlet holes in the USB wall plate over
the 2 raised sockets of the exposed outlet and press the
wall plate to the outlet. Ensure the 2 metal contacts on the
back of the wall plate are alligned with the metal contal
contacts on the sides of the electrical outlet. lnstall the
short white screw provided with the wall plate in the
center hole, to attach the wall plate to the outlet. Now
install the long white screw through the lower hole in the
wall plate. Turn the screwdriver clockwise to tighten the
lower screw,which will pull the wall plate rmly against the
wall.
USBChargePowerWallPlateFrameCover
Smart USB Charge Wall Power Outlet Frame Cover,
Duplex Snap-On USB Fast-Charging Wall Plate
PWPLGU208
This USB wall plate is the easiest way to
add USB Fast-Charging capability to 15
Amp standard decor electrical outlets in
a home or business. For 20Amp outlets,
contact the dealer for alternate units.
Simply replace an existing single decor
wall plate with the Charger and enjoy
easy device charging that's always
ready to go.
The wall plate connects to a 15 amp standard decor outlet
and provides 2 USB charging ports without using up either
outlet electrical socket.
Please follow these directions carefully to safely install this
product.
CAUTION
It is critical to conrm that power has been shut o from the
fuse panel or circuit breaker box to the designated outlet
before starting the replacement. Teplacement of electrical
system wall plates cannot be done safely unless power has
been disconnected at the breaker panel or fuse panel for the
property. Test the outlet, with a voltage meter capable of
making the proper readings prior to the installation of the
wall plate, to ensure power has been disconnected.
You need to prepare a at head screwdriver for this installation.
INSTALLATION
Installing this wall plate takes just 3 simple steps:
1. TURN OFF THE POWER
Locate the electrical cuto point (breaker panel, fuse panel,
etc.) for the outlet to be used. Turn o the breaker switch or
remove the fuse.
Hint - It may help to plug in a lamp or similar device to the
outlet and turn it on. When you have found the correct
breaker or fuse, the light will go out. Additionally test the
outlet with a voltage meter capable of making the proper
1
2
3
Restart power to the outlet after confirming that the
installation is correct!
Congratulation! Your already finished the installation and now
just start to charge.
CLEANING
Clean the charger with a soft,dry cloth. lf a mild detergents
needed to clean tougher spots, shut o the outlet from the
fuse panel or circuit braker box and make sure that no
moisture gets inside the USB ports or outlet on the front of
the unit.
SUPPORT
If you have any questions or concerns which are not
addressed in this document, please contact PyleUSA tech
suupport. Do not attempt to troubleshoot any electrical
outlet without proper training.

Turn o the power
Remove the existing face plate cover
Install the new panel and tightened it
CORRECTINSTALLATIONSTEPS WRONGINSTALLATIONACTION PWPLGU208
USB Charge Power Wall Plate Frame Cover
Smart USB Charge Wall Power Outlet Frame Cover,
Duplex Snap-On USB Fast-Charging Wall Plate
Features:
• Instantly Add Dual USB Charging Ports to Existing
Outlets
• Quick & Hassle-Free ‘Snap-On’ & ‘Screw-In’ Installation
• USB Fast Charge Energy Eciency
• Universal Duplex Size Wall Plate Frame Cover Design
• Clean Installation with Modern Style
• Works with All of Today’s Latest Devices
• Integrated Charging LED Indicator Light
• Reliable, Safety Certied & Lab Tested
• Fireproof, Environmentally Friendly Construction
• Ideal for Home, Oce and Business Use
What’s in the Box:
• USB Wall Plate Frame
• Installation Screws
Technical Specications:
• Duplex Outlet Size/Type: Fits Universal Standard
1-Gang (Single Gang) Square StyleOutlets
• Fast-Charge Support:
15 Amp Standard Electrical Outlets
• USB Port Power Output: 2.1A (x2)
• Construction Material: 94V0 Fire-proof Plastic
• *Duplex Receptacle Not Included
• Power Output: 5V, 3.1A - MAX
• Power Supply: 100-240V, AC
• Dimension (L x W x H): 6.18’’ x 2.83’’ x 1.38’’ -inches
• Sold as: 1
1
2
3
1. Forget to turn
o the switch
2. Take o the power
socket from the wall
3. Finger dig into the
wall socket directly
4. Wrong direction
for the holder
5. Two hands insert hardly
www.PyleUSA.com