Qlightec QWTD Series User manual
QWTDL
-
WS
-
3
-
110/220
-
RAG
[Model number] [Sound] [Layer] [Voltage] [Color]
| | | | |
•
QWTDL
•
QWTDLF
•
WS-Warning sound
•
WP-Special warning
sound
•
WM-Melody
•
WA
-Alarm
•
1-1Layer
•
2-2Layers
•
3-3Layers
•
4-4Layers
•
5-5Layers
•
12-DC12V
•
24-DC24V
•
110/220-AC110V-220V
R-Red
A-Amber
G-Green
B-Blue
W-White
1
Wall Mount LED Signal Tower with Built-in Audible Alarm
QWTD
Ordering Specications
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o-• the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s speci¿cation.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, ¿re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product
that would void the warranty.
1. During wiring or maintenance, please completely turn o-• the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a ¿re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to ¿re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to ¿re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, ¿re, electric shock and loss of life.)
54
-30~+50
85d
B
Please scan the QR code
for more
detailed product information.
www.qlight.com
2
Model
number
Layer
Voltage Current
Certi¿cate
Weight Color
QWTDL
Steady type
QWTDLF
Steady/
Flashing
type
1
AC/DC12V
0.065A 0.14kg
R-Red
AC/DC24V
0.050A 0.14kg
AC110V-220V
Max. 0.025A 0.27kg
2
AC/DC12V
0.130A 0.18kg
R-Red
G-Green
AC/DC24V
0.050A 0.18kg
AC110V-220V
Max. 0.050A 0.32kg
3
AC/DC12V
0.195A 0.23kg
R-Red
A-Amber
G-Green
AC/DC24V
0.150A 0.23kg
AC110V-220V
Max. 0.075A 0.36kg
4
AC/DC12V
0.260A 0.27kg
R-Red
A-Amber
G-Green
B-Blue
AC/DC24V
0.200A 0.27kg
AC110V-220V
Max. 0.100A 0.41kg
5
AC/DC12V
0.325A 0.32kg
R-Red
A-Amber
G-Green
B-Blue
W-White
AC/DC24V
0.250A 0.32kg
AC110V-220V
Max. 0.125A 0.45kg
• Protection rating : IP54
• Ambient operating temperature : -30°C to +50°C
Current speci¿cations
Voltage
condition AC/DC12V AC/DC24V AC110-220V
Light
(Per layer) 0.040A 0.040A Max 0.024A
Sound 0.300A 0.160A Max 0.031A
Type Built-in sound Channel Type of sound
WS 5 Warning
Sounds
Ch1
Ch2
Ch3
Ch4
Ch5
Fire.A-ANG(560Hz-1.5kHz)
Emergency WA-U(600Hz-
1.5kHz)
Ambulance PI-PO(450Hz-
900Hz)
Machinery Fault(820Hz)
High Expansion(1kHz)
WP 5 Special
Warning
Sounds
Ch1
Ch2
Ch3
Ch4
Ch5
Fire.A-ANG(560Hz-1.5kHz)
Abandon Alarm(820Hz)
Machinery Fault(820Hz)
High Expansion(1kHz)
7 Short PI. / 1 Long(1kHz)
WM 5 Melodies
Ch1
Ch2
Ch3
Ch4
Ch5
Sweet Home
For Elise
Cuckoo’s Waltz
Piano Sonata
Turkish March
WA 5 Alarms
Ch1
Ch2
Ch3
Ch4
Ch5
Beep Intermittent
Door Chime
Phone Ring
PI.PI.PI Short
Tripping Beat
QWTD-WS 5 Warning Sounds
QWTD-WP 5 Special Warning Sounds
QWTD-WM 5 Melodies
QWTD-WA 5 Alarms
※AC type model has a free-voltage range of AC100V-240V.
Dimensions
(Unit : mm)
70
L
41
73 40
54
43 41 41 41 41
76
70
6-Ø4 HOLES
Ø13
CABLE ENTRY
21
8
18.5
Ø70
QWTD
LAYER L
1 154
2 195
3 236
4 277
5 318
※ CE compliant : DC12V/24V
Product Specications
Wiring Instructions
3
• QWTD series can be wired with either external contact or transistor.
• For QWTDLF model, user can choose light function between steady and ashing mode through wiring con¿guration.
• External power line - UL1015 AWG18(0.75sq) x 2C 400mm
External signal line - UL1007 AWG22(0.3sq) 400mm
QWTDL-DC/AC
(Steady Type)
QWTDL-DC/AC
(Steady Type)
External Contact
External Contact
External Transistor-NPN
External Transistor-NPN
QWTDLF-DC/AC
(Steady/Flashing Type)
QWTDLF-DC/AC
(Steady/Flashing Type)
Ch 1
Layer1
Layer1
Ch 2
Layer2
Layer2
Ch 3
Layer3
Layer3
Ch 4
Layer4
Layer4
Ch 5
Power
Layer5
Layer5
Ch 1
Layer1
Ch 2
Layer2
Ch 3
Layer3
Ch 4
Layer4
Ch 5
Layer5
Ch 1
Ch 1
Layer1
Layer1
Ch 2
Ch 2
Layer2
Layer2
Ch 3
Ch 3
Layer3
Layer3
Ch 4
Ch 4
Layer4
Layer4
Ch 5
Ch 5
Power
Power
Power
Layer5
Layer5
Red(R)
Amber(A)
Green(G)
Blue(B)
White(W)
Gray/Red(GR/ R)
Gray/Amber(GR/A)
Gray/Green(GR/ G)
Gray/Blue(GR/ B)
Gray/White(GR/ W)
Black(BK)
Red(R)
Amber(A)
Green(G)
Blue(B)
White(W)
Black(BK)
Red(R)
Amber(A)
Green(G)
Blue(B)
White(W)
Violet(VI)
White(W)
Black(BK)
White(W)
Black(BK) White(W)
Black(BK)
Black(BK)
Black(BK)
Violet(VI)
White(W)
Black(BK)
Common
Common
Common
Common
Common
Common
Red(R)
Amber(A)
Green(G)
Blue(B)
White(W)
Gray/Red(GR/ R)
Gray/Amber(GR/A)
Gray/Blue(GR/ B)
Gray/Green(GR/ G)
Gray/White(GR/ W)
Gray/Red(GR/ R)
Gray/Red(GR/ R)
Gray/Amber(GR/A)
Gray/Amber(GR/A)
Gray/Blue(GR/ B)
Gray/Blue(GR/ B)
Gray/Green(GR/ G)
Gray/Green(GR/ G)
Gray/White(GR/ W)
Gray/White(GR/ W)
1
2
3
4
5
Fuse Fuse
Fuse Fuse
Steady
Steady
Flash
Steady
Steady
Flash
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
4
Parts Denition
Sound Selection
■ Guide for WS/WP/WM/WA sound type models
Sound type products are factory set to its speci¿c sound.
The sounds can be con¿gured by using the following table.
Ch1 Ch2 Ch3 17 sounds per combination can be selected according to your preference.4 combinations are
available.
No. 1 2 3 Ch1 Ch2 Ch3 Ch4 Ch5
1000
No sound
2001
SND01 Fire.A-ANG SND02 Emergency WA-U SND03Ambulance PI-PO SND05 Machinery Fault
SND06 High Expansion
3010
SND01 Fire.A-ANG SND04AbandonAlarm SND05 Machinery Fault SND06 High Expansion
SND07 7 Short PI. / 1 Long
4011
SND08 Sweet Home SND09 For Elise SND10 Cuckoo's Waltz SND11 Piano Sonata SND12 Turkish March
5100
SND16 Beep Intermittent SND17 Door Chime SND18 Phone Ring SND19 PI.PI.PI Short SND20 Tripping Beat
ON(1)
OFF(0)
■ Sound Selection Switch
■ Sound Output Section
Please refer to page 4 ‘Sound Selection’
section of this manual for detailed instruction.
Head cover(ABS)
Speaker unit(ABS)
Screw(M4×25mm)
Rubber spacer
(PVC)
Mounting racket
(SPCC)
LED unit(PC)
5
Installation Environment and Protection Rating
•
This product is designed for indoor use with protection rating of IP54.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating
indicated(IP54), it may cause malfunction or damage to the product.
• For further information, please visit our website(www.qlight.com).
Replacing/ Rearranging LED Lens Units
Please ensure the power is o-• before replacing or rearranging the
LED units. Please carefully follow the following instructions.
1. Remove the head cover
②
by loosening the ¿xing screw
①
.
2. Remove the LED unit by pulling it
③
upward.
3. Replace or rearrange the LED units.
4. Assemble in the reverse order of removing the LED units, Be careful
not to let the rubber packing
④
¿tted on the top of each unit come o-•.
①
②
③
④
Installation
• The user need to install the mounting bracket on to the mounting surface ¿rst to ¿x the product body on to the mounting surface.
• Drill proper mounting holes in accordance with the number of LED lens unit, referring to the installation diagrams below.
① Remove the mounting bracket from the product by removing
two M4 screws from the speaker unit.
②Mount the mounting bracket to the mounting surface.
③ Hook the rear of the head cover to the upper bracket, then
push the body against the mounting bracket.
④After tightly attaching the product body to the mounting
bracket, tighten the two M4 screws removed in step ① at the
bottom of the speaker unit.
①
②
③ ④
M4-25 BOL
T
M4-25 BOLT
41414141
43
21
414141
43
21
43
21
41
43
21
4141
43
21
3-Ø4 HOLES
2-Ø4 HOLES
5-Ø4 HOLES
4-Ø4 HOLES
6-Ø4 HOLES
Ø13 CABLE
ENTRY
Ø13 CABLE
ENTRY
Ø13 CABLE
ENTRY
Ø13 CABLE
ENTRY
Ø13 CABLE
ENTRY
Product installation direction
■ Install the product in accordance with the manual. Otherwise rainwater or moisture may penetrate into the product.
ㆍ ELECTRONIC SOUNDER/SIGNAL HORN
Sounder part shall not be facing the sky.
Sounder part shall not be facing the sky.
ㆍBEACON/SIGNALING LIGHT
Power cord inlet part shall not be facing the sky.
Power cord inlet part shall not be facing the sky.
ㆍSIGNAL TOWER LIGHTS
ㆍHEAVY-DUTY & EXPLOSION PROOF SIGNALINGS
※ For products with a protection rating of less than IPX4, please install it vertically.
※ For products with a protection rating of less than IPX4, please install it vertically.
MEMO
Head O-ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. +82-2-2679-6152(Toll free. +82-80-328-2222) Fax. +82-2-2679-6154
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. +82-55-328-1111(Toll free. +82-80-328-1111)
Qlight OverSEAs Sales Dept |
704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : +82-51-620-4100
Qlight Public Relations & Marketing Team O-ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. +82-51-245-0017
3003 North First Street, Suite #341, San Jose, CA 95134 USA Tel. +1 - 408 - 519 - 5740 Fax. +1 - 408 - 519 - 5739
China Factory/ Shanghai Sales O-ce | #19, Nanda Road, Baoshan Area, Shanghai, China Tel. +86
-
21
-
6651
-
7100 Fax. +86
-
21
-
6315
-
3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86
-
513
-
8384
-
9999 Fax +86
-
513
-
8384
-
9910
Product Operation Inquiry / Customer Support +82-51-620-4100
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea ( Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea ( Postal Code : 50805)
For your safety
Speci¿cation and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - QWTD -2207A
Table of contents
Other Qlightec Security System manuals
