Qlightec QMPS User manual
1
Panel Mount Audible Alarm
QMPS
QMPS -12/24
[Model number] [Voltage]
| |
• QMPS
• 12/24-DC12V-24V
• 110/220-AC110V-220V
Model
number Voltage Current Sound Volume
(dB) Input Method/
No.of ch
&HUWL¿FDWH
Weight
QMPS
DC12V-24V Max. 0.750A
• Warning : 98dB
•
MP3
: 95dB
Bit Input:5Ch
Binary Input:30Ch
0.35kg
AC110V-220V Max. 0.100A
0.53kg
※DC type model has a free-voltage range of DC10V-30V.
※AC type model has a free-voltage range of AC100V-240V.
※CE Compliant, UL Listed : DC12V/24V
• Protection rating : IP54
• Ambient operating temperature : -25°C to +50°C
54
5025
95d
B
98d
B
Please scan the QR code for
more detailed product information.
www.qlight.com
ON
RUN
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
3OHDVHWXUQRWKHSRZHURIWKHSURGXFWLPPHGLDWHO\LILWIDLOVWRRSHUDWHSURSHUO\
&DUHIXOO\ZLUHWKHSURGXFWDFFRUGLQJWRHDFKSURGXFW¶VVSHFL¿FDWLRQ
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
)DLOXUHWRIROORZDQ\RIWKHLQVWUXFWLRQVDERYHPD\FDXVHPDOIXQFWLRQRUGDPDJHWRWKHSURGXFW¿UHDQGHOHFWULFVKRFN
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, and or malfunction of the
product that would void the warranty.
’XULQJZLULQJRUPDLQWHQDQFHSOHDVHFRPSOHWHO\WXUQRWKHSRZHURIWKHSURGXFW)DLOXUHWRIROORZWKLVPD\OHDGWRDQHOHFWULFVKRFN
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
UDWLQJVLQGLFDWHGIRUHDFKSURGXFW)DLOXUHWRIROORZWKHVHLQVWUXFWLRQVPD\FDXVHD¿UHWRWKHSURGXFWHOHFWULFVKRFNSK\VLFDOLQMXU\
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
IROORZWKHVHLQVWUXFWLRQVPD\OHDGWR¿UHHOHFWULFVKRFNRUSURGXFWGDPDJH
3OHDVHDSSO\WKHFRUUHFWYROWDJHWRWKHSURGXFW)DLOXUHWRIROORZWKHVHLQVWUXFWLRQVPD\OHDGWR¿UHHOHFWULFVKRFNRUSURGXFWGDPDJH
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
IROORZWKLVPD\FDXVHGDPDJHWRSURSHUW\¿UHHOHFWULFVKRFNDQGORVVRIOLIH
Ordering Specications
Product Specications
2
ON
RUN
5018
68
120
126
4
120
60
111
111
• When wiring the product with an external transistor, both NPN and PNP type transistors can be used.
QMPS-DC QMPS-AC
EXTERNAL CONTACT
SOUND DW
STOP
Fuse
Active at Busy
Maximum Load
500mA
Maximum Load
500mA
Maximum Load
500mA Maximum Load
500mA
Maximum Load
500mA
Maximum Load
500mA
Active at Busy
Active at Busy Active at Busy
Common
Common
Common
Active at Busy
Active at Busy
POWER
POWER
POWER
POWER
POWER
POWER
STOP
STOP
STOP
STOP
STOP
SOUND DW
SOUND DW
SOUND DW
SOUND DW
SOUND DW
EXTERNAL CONTACT
EXTERNAL TRASISTOR-NPN EXTERNAL TRASISTOR-NPN
EXTERNAL TRASISTOR-PNP
EXTERNAL TRASISTOR-PNP
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Fuse
Fuse Fuse
Fuse
Fuse
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
2 - Mounting Bracket
QMPS
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
Dimensions
(Units : mm)
Wiring Instructions
3
RUN
ON
SOUND SET
SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
Parts Denition
Installation
ㆍㆍFirst, cut a square hole (see the above dimensions) on the panel ①to mount the product.
ㆍㆍInsert the rubber packing ②and the product into the square hole of the panel.
ㆍㆍPlace the mounting bracket (2EA) ③and ④(provided with the product) on the sides of the body and tighten it with a screwdriver ⑤
please ensure the screws are securely tightened.
ㆍㆍMax. thickness allowed for mounting panel is 10mm.
- SD cards are sold separately.
RUN
ON
SOUND SET
SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
Mounting Bracket Operation
Indicator
Body (ABS)
Rubber Packing Terminal Block Cover
(PC)
Back Cover (ABS) Terminal Block
Front Cover (ABS)
Sound Selection Switch
Volume Switch
Play Mode Setting Switch
Fixing Bolt SD Card Slot
Installation Environment and Protection Rating
• This product is designed for use with protection rating of IP54.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating indica-
ted(IP54), it may cause malfunction or damage to the product.
• For further information, please visit our website(www.qlight.com).
SD Card
4
RUN
ON
SOUND SET
SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
①The red indicator light is on when voltage is supplied to the power
terminal.
②
The green indicator light is on when the product is operating normally.
Operation Indicator
①/RRVHQWKHFRYHU¿[LQJEROW0IDVWHQHGDWWKHERWWRPRIWKH
product.
②Gently press down the front cover and pull it down. (be careful that
WKHFRYHUPD\IDOORLI\RXDSSO\H[FHVVLYHIRUFH
• Can select between channel input methods (bit/ binary) and
various playback modes.
• 8VHDDWVFUHZGULYHUWRURWDWHRQHVSDFHDWDWLPH
(regardless of the direction of rotation.)
• Switch 0 and 9 have no function.
Removing the Front Cover
PLAY MODE
1 Bit Input Mode
• Play back one of the 5 built-in or external
sounds once
• For a built-in sound, the playback time is
about 10 seconds
2 Binary Input Mode
• Play back one of the 30 built-in or external
sounds once
• For a built-in sound, the playback time is
about 10 seconds
3Bit Input Hold
Playback Mode
• Play back one of the 5 built-in or external
sounds continuously
4Binary Input Hold
Playback Mode
• Play back one of the 30 built-in or external
sounds continuously
5Bit Input Sound
Reduction Mode
• Decrease the volume of the selected channel
by 15dB
• Play back one of the 5 built-in or external
sounds continuously
6Binary Input Sound
Reduction Mode
• Decrease the volume of the selected channel
by 15dB
• Play back one of the 30 built-in or external
sounds continuously
7Bit Input Sequence
Memory Playback
Mode
• When other channel signals are continuously
inputted within 3 seconds after inputting the
channel, the input order is memorized and
playback in the memorized order (playback
time is 3 - 5 seconds)
• The last input channel is played continuously
(Bit input only)
8 Test Mode
• In the test mode, the Ch1 of the built-in sound
or the external sound is automatically played
continuously
• Switch back to another mode to exit test mode
RUN
ON
SOUND SET
SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
RUN
ON
SOUND SET SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
PLAY MODE
Removing the front cover
Red steady light
Green ashing light
RUN
ON
SOUND SET SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
SD Card Slot
Sound
Selection
Switch
Play Mode
Selection
Switch
Volume Switch
Front Control Panel
Front Control Conguration
•
Select
between built
-in sounds and external
sounds (SD Card) using the sound selection
switch.
• Please be conscious of the number
selected
for your desired sound option.
- Switch 1 :
Can select between built-in
sound
and external sound options(SD Card).
- Switch 2,3 and 4 :
Can select sound group
from built-in sounds.
■ Select Built-in Voice Group
■
Selection between Built-in Sound and External Sound
(SD Card Type)
•
This is used when built-in sound mode is selected.
• Select between the six sound groups.
• Every group has 5 type of sounds.
• To play built-in sounds, set the sound setting
switch to the OFF (0) position.
• To play an external sound on the SD card, insert
the SD card into SD card slot and set the sound
setting switch to ON (1).
How to select bit type sound group
Sounds
No. 2 3 4
1 0 0 1
5 Warning Sounds
2 0 1 0
5 Special Warning Sounds (1st Group)
3 0 1 1
5 Melodies
4 1 0 0
5Alarms
5 1 0 1
5 Special Warning Sounds (2nd Group)
6 1 1 0
5 Special Warning Sounds (3rd Group)
ON(1)
OFF(0)
Sound Setting
Play Mode Setting
Play mode switch
Can rotate
regardless of
direction
5
RUN
ON
SOUND SET SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
RUN
ON
SOUND SET
SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
Rear Terminal Block Conguration
①
Terminal for power input.
②
The auxiliary terminal block outputs power that can operate auxiliary
equipment.
- Input voltage (DC12V) : DC11V output
- Input voltage (DC24V) : DC23V output
- Input voltage (AC) : DC24 ± 10% output
③
COM terminal for channel selection. Refer to Page2 for connection
method information.
④
Sound channel selection terminal. You can select the sound by using
external contact or transistor.
⑤
SOUND DW : When the terminal is connected, playback volume
is reduced by 15dB.
⑥
Stop playback (STOP) : When the terminal is connected during play-
back, playback stops.
Connects power
Provides auxiliary
power output
during operation
Bit/ Binary input method using rear
terminal block
•
%LWLQSXWPRGHXVLQJH[WHUQDOOLQHDOORZV\RXWRVHOHFWRQHRI¿Y
e
sound options by switching on one of the 5 channels(Ch1 - Ch5).
7RWDORIVRXQGRSWLRQVDUHFRQ¿JXUDEOH
■
Wiring through terminal block with either external contact
or NPN transistor allows either bit or binary input method for
sound channel selection.
•
Binary input mode(using external line)allows you to receive multiple inputs
E\XVLQJWKHFKDQQHOV&K&KWRFRQ¿JXUHRQHRIVRXQGRSWLRQV
•7RWDORIVRXQGRSWLRQVDUHFRQ¿JXUDEOH
■ Bit Input Mode
■ Binary Input Mode
No. 1 2 3 4 5
0 0 0 0 0 0
1 1 0 0 0 0
2 0 1 0 0 0
3 0 0 1 0 0
4 0 0 0 1 0
5 0 0 0 0 1
※
Please note that the
switches shown on the
table is to explain how
to wire the terminal block.
Actual products do not
have switches attached.
Terminal box
0 0 0 0 0 0
1 0 0 0 0 1
2 0 0 0 1 0
29 1 1 1 0 1
30 1 1 1 1 0
ON(1)
OFF(0)
CH1 CH3CH2 CH4 CH5
COM
EXTERNALCONTACT
Binary input mode
Can select up to
30 sound options
Bit input mode
Can select up to
5 sound options
• The volume output of this product is adjustable.
• Turn the volume dial clockwise to increase the volume, and
turn counter clockwise to decrease the volume.
• There will be no sound when the dial is put at MIN.
Volume Dial
Volume Adjustment
VOL.
MIN.
MAX.
• 6’FDUGVSHFL¿FDWLRQV
- Use standard SD card.
- Mini SD or Micro SD also can be used
with adaptor.
- SD, SDHC type supported
- Storage capacity : Max. 32GB
&ODVV1RVSHFL¿FDWLRQ
• 3OHDVHVDYHWKH03VRXQG¿OHRQWKH6’FDUGDVVKRZQEHORZ
• Create an “MP3_FILE” folder on the SD card and save the MP3
¿OHLQWKHIROORZLQJ¿OHIRUPDW
• 03¿OHIRUPDW
• :KHQVDYLQJ¿OHVSOHDVHVDYHWKHPLQRUGHU
- Please start saving after formatting the SD card.
• 7KHOHQJWKRIWKH¿OHQDPHPXVWQRWH[FHHGFKDUDFWHUV
23 _ For Elise .mp3
Filename (Up to 40 characters)
6HSDUDWRU7UDFNDQG¿OHWLWOH
Track# (01-30)
01_Fire.mp3
02_Emergency.mp3
03_For Elise.mp3
30_Cuckoo's Waltz.mp3
[Example]
SD Card Specications and Sound
Saving Manual
6
• In bit input mode, you can chooses one sound from 5 sounds
E\FRQ¿JXULQJWKHFKDQQHOV
•
This product has a terminal block to select a sound source. For further
details, refer to page 5 ‘Bit/ Binary Input Method using Rear Terminal
Block’ section of this manual.
• )RUVRXQGFRQ¿JXUDWLRQVUHIHUWRWKHWDEOHEHORZ
■ Bit Input - Playing Built-in Sound
%LWLQSXWPHWKRGVRXQGFRQ¿JXUDWLRQ
Type of sound
(WS group as an example)
No. 1 2 3 4 5
0 0 0 0 0 0 No sound
1 1 0 0 0 0 Fire.A-ANG(560Hz-1.5kHz)
2 0 1 0 0 0 Emergency WA-U (600Hz-1.5kHz)
3 0 0 1 0 0 Ambulance PI-PO (450Hz-900Hz)
4 0 0 0 1 0 Machinery Fault(820Hz)
5 0 0 0 0 1 High Expansion(1kHz)
ON(1)
OFF(0)
Sound Type and Combination Manual
■ Sound Type by Group
%LWLQSXWPHWKRGVRXQGFRQ¿JXUDWLRQ
Group
Channel
Type of sound
WS
5 Warning
Sounds
Ch1
Fire.A-ANG (560Hz-1.5kHz)
Ch2
Emergency WA-U (600Hz-1.5kHz)
Ch3
Ambulance PI-PO (450Hz-900Hz)
Ch4
Machinery Fault (820Hz)
Ch5
High Expansion (1kHz)
WP
5 Special
Warning
Sounds
(1st Group)
Ch1
Fire.A-ANG (560Hz-1.5kHz)
Ch2
Abandon Alarm (820Hz)
Ch3
Machinery Fault (820Hz)
Ch4
High Expansion (1kHz)
Ch5
7 Short PI. / 1 Long (1kHz)
WM 5 Melodies
Ch1
Sweet Home
Ch2
For Elise
Ch3
Cuckoo's Waltz
Ch4
Piano Sonata
Ch5
Turkish March
WA 5 Alarms
Ch1
Beep Intermittent
Ch2
Door Chime
Ch3
Phone Ring
Ch4
PI.PI.PI Short
Ch5
Tripping Beat
WO
5 Special
Warning
Sounds
(2nd Group)
Ch1
Rel rel rel (730Hz-920Hz)
Ch2
Slow Ambulance PI-PO (820Hz-1.05kHz)
Ch3
Wye yong Wye yong (770Hz-1.2kHz)
Ch4
Phone ring 2 (740Hz-910Hz)
Ch5
Fire.A-ANG (770Hz-1.11kHz)
WN
5 Special
Warning
Sounds
(3rd Group)
Ch1
Oit Oit (500Hz-1.11kHz)
Ch2
Pi o Pi o (940Hz-2.19kHz)
Ch3
Slow Di o Di o (680Hz-840Hz)
Ch4
Li long Li ling (420Hz-470Hz)
Ch5
911 Siren (150Hz-1kHz)
※ 3OHDVHEHQRWHGWKDWWKHFRQ¿JXUDWLRQFKDUWDERYHLVH[SODLQLQJ
how to wire terminal blocks. The actual product does not have a
switch.
※ 3OHDVHEHQRWHGWKDWWKHFRQ¿JXUDWLRQFKDUWDERYHLVH[SODLQLQJ
how to wire terminal blocks. The actual product does not have a
switch.
•
In binary input mode, you can chooses one sound from
30
VRXQGVE\FRQ¿JXULQJWKHFKDQQHOV
•
This product has a terminal block to select a sound source. For further
details, refer to page 5 ‘Bit/ Binary Input Method using Rear Terminal
Block’ section of this manual.
• )RUVRXQGFRQ¿JXUDWLRQVUHIHUWRWKHWDEOHEHORZ
• 3OHDVHEHDZDUHWKDWWKHFRQ¿JXUDWLRQIRUVRXQGXVLQJWKH
ELQDU\LQSXWPHWKRGLVGLHUHQWIURPWKHELWLQSXWPHWKRG
■ Binary Input - Playing Built-in Sound
%LQDU\LQSXWPHWKRGVRXQGFRQ¿JXUDWLRQ
Type of sound
No. 1 2 3 4 5
0 0 0 0 0 0 No sound
1 0 0 0 0 1 Fire.A-ANG (560Hz-1.5kHz)
2 0 0 0 1 0 EmergencyWA-U (600Hz-1.5kHz)
3 0 0 0 1 1 Ambulance PI-PO (450Hz-900Hz)
4 0 0 1 0 0 Pi-ik Pi-ik (800Hz)
5 0 0 1 0 1 Machinery Fault (820Hz)
6 0 0 1 1 0 High Expansion (1kHz)
7 0 0 1 1 1 Alarm (1kHz)
8 0 1 0 0 0 Sweet Home
9 0 1 0 0 1 For Elise
10 0 1 0 1 0 Cuckoo's Waltz
11 01011Piano Sonata
12 0 1 1 0 0 Turkish March
13 0 1 1 0 1 Magic Flute
14 0 1 1 1 0 Badinerie
15 0 1 1 1 1 Pineapple Rag
16 1 0 0 0 0 Beep Intermittent
17 1 0 0 0 1 Door Chime
18 1 0 0 1 0 Phone Ring
19 1 0 0 1 1 PI.PI.PI Short
20 1 0 1 0 0 Tripping Beat
21 1 0 1 0 1 Rel rel rel (730Hz-920Hz)
22 1 0 1 1 0 Slow Ambulance PI-PO
(820Hz-1.05kHz)
23 1 0 1 1 1 Wye yong Wye yong
(770Hz-1.2kHz)
24 1 1 0 0 0 Phone ring 2 (740Hz-910Hz)
25 1 1 0 0 1 Fire.A-ANG (770Hz-1.11kHz)
26 1 1 0 1 0 Oit Oit (500Hz-1.11kHz)
27 1 1 0 1 1 Pi o Pi o (940Hz-2.19kHz)
28 1 1 1 0 0 Slow Di o Di o (680Hz-840Hz)
29 1 1 1 0 1 Li long Li ling (420Hz-470Hz)
30 1 1 1 1 0 911 Siren (150Hz-1kHz)
ON(1)
OFF(0)
7
※ 3OHDVHEHQRWHGWKDWWKHFRQ¿JXUDWLRQFKDUWDERYHLVH[SODLQLQJ
how to wire terminal blocks. The actual product does not have a
switch.
※ 3OHDVHEHQRWHGWKDWWKHFRQ¿JXUDWLRQFKDUWDERYHLVH[SODLQLQJ
how to wire terminal blocks. The actual product does not have a
switch.
•
User can save sounds(MP3) to the SD card and able to select
1 sounds from 5 saved sounds.
ㆍㆍ
For channel selection
method using terminal block, refer to page 5
‘Bit/
Binary Input Method using Rear Terminal Block’
section of this
manual.
• )RUVRXQGFRQ¿JXUDWLRQVUHIHUWRWKHWDEOHEHORZ
•
Binary input mode chooses one of the 30 sounds by combining
WKHRQRVZLWFKRIWKHGLHUHQWFKDQQHOVWRWKHDVVRFLDWHGWRQH
ㆍㆍ
For channel selection
method using terminal block, refer to page 5
‘Bit/
Binary Input Method using Rear Terminal Block’ section of this manual.
•
)RUVRXQGFRQ¿JXUDWLRQVUHIHUWRWKHWDEOHEHORZ
•
3OHDVHEHDZDUHWKDWWKHFRQ¿JXUDWLRQIRUVRXQGXVLQJWKH
ELQDU\LQSXWPHWKRGLVGLHUHQWIURPWKHELWLQSXWPHWKRG
■ Bit Input - Playing External Sound (SD Card) ■ Binary Input - Playing External Sound (SD Card)
%LWLQSXWPHWKRGVRXQGVRXUFHFRQ¿JXUDWLRQ
Type of sound
No. 1 2 3 4 5
0 0 0 0 0 0
No sound
1 1 0 0 0 0
Custom sound 1(01_xxx.mp3)
2 0 1 0 0 0
Custom sound2(02_xxx.mp3)
3 0 0 1 0 0
Custom sound3(03_xxx.mp3)
4 0 0 0 1 0
Custom sound4(04_xxx.mp3)
5 0 0 0 0 1
Custom sound5(05_xxx.mp3)
ON(1)
OFF(0)
ON(1)
OFF(0)
%LQDU\LQSXWPHWKRGVRXQGVRXUFHFRQ¿JXUDWLRQ
Type of sound
No. 1 2 3 4 5
0 0 0 0 0 0
No sound
1 0 0 0 0 1
Custom sound1(01_xxx.mp3)
2 0 0 0 1 0
Custom sound2(02_xxx.mp3)
3 0 0 0 1 1
Custom sound3(03_xxx.mp3)
4 0 0 1 0 0
Custom sound4(04_xxx.mp3)
5 0 0 1 0 1
Custom sound5(05_xxx.mp3)
6 0 0 1 1 0
Custom sound6(06_xxx.mp3)
7 0 0 1 1 1
Custom sound7(07_xxx.mp3)
8 0 1 0 0 0
Custom sound8(08_xxx.mp3)
9 0 1 0 0 1
Custom sound9(09_xxx.mp3)
10 0 1 0 1 0
Custom sound10(10_xxx.mp3)
11 01011
Custom sound11(11_xxx.mp3)
12 0 1 1 0 0
Custom sound12(12_xxx.mp3)
13 0 1 1 0 1
Custom sound13(13_xxx.mp3)
14 0 1 1 1 0
Custom sound14(14_xxx.mp3)
15 0 1 1 1 1
Custom sound15(15_xxx.mp3)
16 1 0 0 0 0
Custom sound16(16_xxx.mp3)
17 1 0 0 0 1
Custom sound17(17_xxx.mp3)
18 1 0 0 1 0
Custom sound18(18_xxx.mp3)
19 1 0 0 1 1
Custom sound19(19_xxx.mp3)
20 1 0 1 0 0
Custom sound20(20_xxx.mp3)
21 1 0 1 0 1
Custom sound21(21_xxx.mp3)
22 1 0 1 1 0
Custom sound22(22_xxx.mp3)
23 1 0 1 1 1
Custom sound23(23_xxx.mp3)
24 1 1 0 0 0
Custom sound24(24_xxx.mp3)
25 1 1 0 0 1
Custom sound25(25_xxx.mp3)
26 1 1 0 1 0
Custom sound26(26_xxx.mp3)
27 1 1 0 1 1
Custom sound27(27_xxx.mp3)
28 1 1 1 0 0
Custom sound28(28_xxx.mp3)
29 1 1 1 0 1
Custom sound29(29_xxx.mp3)
30 1 1 1 1 0
Custom sound30(30_xxx.mp3)
Sound Type and Combination
8
Operation Method and Setting
When Using a Built-in Sound Source When Using an External Sound Source (SD Card)
Bit input Binary input Bit input Binary input
3OD\RQHRI¿YHVRXQGVIURP
6 groups Play one of 30 sounds Play one of 5 sounds stored
by the user Play one of 30 sounds stored
by the user
■ When using a built-in sound source in bit input mode
■ When using a built-in sound source in binary input
mode
1. Set the no. 1 switch of the SOUND setting switch to OFF to select
built-in sound.
- For more information, see page 4
‘Sound Selection’
section.
2. Use one of the SOUND setting switches 2, 3and 4 to select one of the
6 groups.
- For more information, see page 4
‘Sound Selection’
section.
3. Use the PLAY MODE setting switch to choose one of the modes
between 1, 3, 5, 7, or 8.
- Mode 8 is a test mode which continuously plays channel 1. (Channel
selection is disabled.)
- For details, refer to page 4
‘Play Mode Setting’
section.
8VHWKHWHUPLQDOEORFNRQWKHEDFNWRVHOHFWRQHRIWKH¿YHEXLOWLQ
sounds.
- For more information, please refer to page 6
‘Sound Type and Combi-
nation for Built-in Sound’ - ‘Bit Input’
section.
1. Set the no. 1 switch of the SOUND setting switch to OFF to select the
built-in sound.
- For more information, see page 4
‘Sound’
section.
2. Use one of the SOUND setting switches 2, 3 and 4 to select one of the
6 groups.
- For more information, see page 4
‘Sound Selection’
section.
3. Use the PLAY MODE setting switch to select one of the modes be-
tween 2, 4, 6, or 8.
- The 8th function is the test mode and the sound of channel 1 is continu-
ously played. (Channel selection is disabled.)
- For details, refer to page 4
‘Play Mode Setting’
section.
4. Use the terminal block on the back to select one of the 30 built-in
sounds.
- For details, please refer to page 6
‘Sound Type and Combination for
Built-in Sound’ - ‘Binary input’
section.
■ When using an external sound source (SD Card) in bit
input mode
■ When using an external sound source (SD Card)
source in binary input mode
※Insert SD card → Sound switch setting → Play mode switch
setting → Channel selection
※Insert SD card → Sound switch setting → Play mode switch
setting → Channel selection
※Sound switch setting → Play mode switch setting
→ Channel selection
※Sound switch setting → Play mode switch setting
→ Channel selection
1.
Please refer to page 5
‘How to Select SD Card and Save Sound Files’
VHFWLRQWRVHHKRZWRVDYHVRXQG¿OHV
- Supports up to 5 sound sources.
2. Insert the SD Card into the SD Card slot.
3. Set the no. 1 switch of the SOUND Selection switch to ON to select
external sound.
- For more information, see page 4
‘Sound Selection’
section.
4. Use the PLAY MODE setting switch to select 1, 3, 5, 7 or 8 mode.
- Mode 8 is a test mode which continuously plays channel 1. (Channel
selection is disabled.)
- For details, refer to page 4
‘Play Mode Setting’
section.
5. To select a channel, use the terminal block on the back to select one of
the 5 sounds stored by the user.
- For more information, please refer to page 7
‘Sound Type and Combi-
nation for SD Card’ – ‘Bit Input’
section.
1. Please refer to page5
‘How to Select SD Card and Save Sound Files’
VHFWLRQWRVHHKRZWRVDYHVRXQG¿OHV
- Supports up to 30 sound sources.
2. Insert the SD Card into the SD Card slot.
3. Set the no. 1 switch of the SOUND selection switch to ON to select
external sound.
4. Use the PLAY MODE setting switch to select one of the modes be-
tween 2, 4, 6, or 8.
- Mode 8 is a test mode which continuously plays channel 1.(Channel
selection is disabled.)
- For details, refer to page 4
‘Play Mode Setting’
section.
5. Use the sound selection switch to select one of the 30 sounds stored
by the user.
- For details, please refer to page 7
‘Sound Type and Combination for
SD Card’ – ‘Binary Input’
section.
Product installation direction
■ Install the product in accordance with the manual. Otherwise rainwater or moisture may penetrate into the product.
ㆍELECTRONIC SOUNDER/SIGNAL HORN
Sounder part shall not be facing the sky.
Sounder part shall not be facing the sky.
ㆍBEACON/SIGNALING LIGHT
Power cord inlet part shall not be facing the sky.
Power cord inlet part shall not be facing the sky.
ㆍSIGNAL TOWER LIGHTS
ㆍHEAVY-DUTY & EXPLOSION PROOF SIGNALINGS
※For products with a protection rating of less than IPX4, please install it vertically.
※For products with a protection rating of less than IPX4, please install it vertically.
MEMO
MEMO
+HDG2FH_6XLWH67;97RZHU*DVDQGLJLWDOUR*HXPFKHRQJX6HRXO.RUHD
Tel. +82-2-2679-6152(Toll free. +82-80-328-2222) Fax. +82-2-2679-6154
)DFWRU\_0XNEDQJUR6DQJGRQJP\HRQ*LPKDHVL*\HRQJVDQJQDPGR.RUHD7HO7ROOIUHH
Qlight OverSEAs Sales Dept |
1DNGRQJGDHUR6DVDQJJX%XVDQ.RUHD(RPJXQJ’RQJ7HO
4OLJKW3XEOLF5HODWLRQV0DUNHWLQJ7HDP2FH_1DNGRQJGDHUR6DVDQJJX%XVDQ.RUHD(RPJXQJ’RQJ7HO
3003 North First Street, Suite #341, San Jose, CA95134 USATel. +1-408-519-5740 Fax. +1-408-519-5739
&KLQD)DFWRU\6KDQJKDL6DOHV2FH_1DQGD5RDG%DRVKDQ$UHD6KDQJKDL&KLQD7HO
-
21
-
6651
-
7100 Fax. +86
-
21
-
6315
-
3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86
-
513
-
8384
-
9999 Fax +86
-
513
-
8384
-
9910
Product Operation Inquiry / Customer Support +82-51-620-4100
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALLPRODUCT, PRODUCT SPECIFICATIONS AND DATAARE SUBJECT TO CHANGE WITHOUTNOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
+HDGRIILFH6XLWH67;97RZHU*DVDQGLJLWDOUR*HXPFKHRQJX6HRXO.RUHD (Postal Code : 08507)
)DFWRU\0XNEDQJ5R6DQJGRQJ0\HRQ*LPKDH6L*\HRQJVDQJQDP’R.RUHD Postal Code : 50805)
For your safety
6SHFL¿FDWLRQDQGGLPHQVLRQVOLVWHGLQWKLVFDWDORJXHVXEMHFWWRFKDQJHZLWKRXWQRWLFHIRUSURGXFWTXDOLW\LPSURYHPHQW
7KHQHZHVWSURGXFWLQIRUPDWLRQLVDYDLODEOHRQRXUZHEVLWHZZZTOLJKWFRP
3OHDVHUHDGWKHLQVWUXFWLRQPDQXDODWWDFKHGWRWKHSURGXFWFDUHIXOO\EHIRUHLQVWDOODWLRQDQGXVH
www.qlight.com
EN - QMPS - 2206A
Table of contents
Other Qlightec Security System manuals
