RAB Lighting ALED 52W User manual

ALED 52W INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
®
MOUNTING ALED52 TO POLE
Mount directly to 4” or larger square steel pole. Do not separate Pole Arm from Housing.
1. Remove Pole Arm Cover Plate by loosening two screws.
2. Place Pole Gasket between the Pole Arm and drilled Pole as shown. Line up center hole with center hole in the pole drilling
pattern.
3. Insert 3/8-16 x 1 1/4” Bolts from the Pole Arm thru the top hole of the Pole and thread into the Bolster Plate. Longer 2 1/4”
bolts provided for use with round pole and round pole adaptor. For PAD4 applications use bolts, nuts, lockwashers and
washers and tighten inside the PAD4. Do not use bolster plate.
4. Knot wires in pole for strain relief and feed wires from the pole into the Pole Arm. Make the necessary wiring connections in
the Pole Arm.
5. Install the Arm Gasket on to the Pole Arm Cover Plate and secure it with the screws. Cover the screws with provided caps.
Install the Pole Cap.
Bolster Plate
Housing
Pole Arm
Bolts, Washer and
Lockwasher
Pole Cap
Pole Gasket
Pole Arm Cover
Plate
Arm Gasket
ALED52
Standard (15 Deg) ALEDC52
Cuto (7.5 Deg)
ALEDFC52
Full Cuto (0 Deg)
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

ALED 52W INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
®
POLE DRILING DETAIL
For non-RAB poles use these dimensions to drill the pole. This template is not to scale. Please use measurements shown.
WIRING
Universal voltage driver permits operation at 120V to 277VAC,
50 or 60 Hz except xtures factory ordered with a 120V swivel
photocell (/PCS) or 277V swivel photocell (/PCS2)
1. Connect the BLACK xture lead to the (+) LINE supply lead.
2. Connect the WHITE xture lead to the (-) COMMON supply
lead.
3. Connect the bare copper Ground wire from xture to
supply ground.
TROUBLESHOOTING
1. Check that the line voltage at the xture is correct. Refer
to wiring directions.
2. Is the xture grounded properly?
3. Be sure the photocell, if used, is functioning properly.
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough
to touch. Do not clean or maintain while xture is
energized.
1. Clean glass lens with non-abrasive glass cleaning
solution.
2. Do not open the xture to clean the LED. Do not touch
the LED.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly [e-mail]
ALED52 IN 0114
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during
installation, operation or maintenance.
Patents: US: pat. D653,377

ALED 52W INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
®
ALED52 Cool
ALED52N Neutral
ALEDFC52 CoolALEDC52 Cool
ALEDC52N Neutral ALEDFC52N Neutral

ALED 52 & WPLED 52 BILEVEL INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
®®
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2012 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly [e-mail]
ALED52/BL WPLED52/BL IN 0414
MOUNTING ARM ON FIXTURE
1. Bi-level xtures have LED’s wired in pairs. The two pairs are shown below.
2. Each pair has leads brought through the arm and labeled.
3. Use the pairs for switching as needed in your application.
Set #2Set #1