RAB Lighting GOOSE User manual

GOOSE & ARM24 INSTALLATION INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable
parts inside.
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call
the Marketing Department at 888-RAB-1000, or email: [e-mail]
GOOSE
CAUTION: Use mounting hardware appropriate for
the mounting surface and weight of the xture.
1. Make supply connections in recessed junction box.
2. Mount Wall Plate to wall through (4) Mounting Holes
using appropriate hardware for your
mounting surface.
3. Mount xture on other end of GOOSE. Works with
any 1/2” NPS threaded mounting.
4. Tighten Set Screws and all other screws
and hardware.
5. To ensure weatherproof seal, apply weatherproof
silicone sealant to all unused plugs and holes and all
along the edge of the Wall Plate. Use Teon tape or
use weatherproof silicone sealant on Goose threads.
Mounting
Holes (4)
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.
GOOSE ARM24 IN 0612
GOOSE
Wall Plate
ARM24
CAUTION: Use mounting hardware appropriate for
the mounting surface and weight of the xture.
1. Make supply connections in recessed junction box.
2. Mount Wall Plate to wall through (4) Mounting Holes
using appropriate hardware for your
mounting surface.
3. Mount xture on other end of ARM24. Works with
any 1/2” NPS threaded mounting.
4. Tighten Set Screws and all other screws
and hardware.
5. To ensure weatherproof seal, apply weatherproof
silicone sealant to all unused plugs and holes and all
along the edge of the Wall Plate. Use Teon tape or
use weatherproof silicone sealant on Arm24 threads.
ARM24
Wall Plate
Set
Screws (2)
Mounting
Holes (4)
Set
Screws (2)

ARMSV24 INSTALLATION INSTRUCTIONS
ARMSV24
24” Arm with swivel for WPLED10, WPLED13 and WPLED20 (Fixtures sold separately).
CAUTION: Follow mounting orientation restrictions on xture instructions.
1. Remove Door from xture. Remove junction box or mounting plate from xture. Connect leads from ARMSV24 to
xture. Make the wiring connections inside of the xture using UL approved connectors.
2. Mount the Swivel Adaptor to the xture with four Housing Screws. Use the provided nuts and washers for two of the
four Housing Screws as shown below.
3. Replace Door. Tighten all door screws and check seal of door gasket.
4. Make supply wiring connections in recessed junction box with UL approved connectors. Mount Wall Plate and xture
assembly to wall with hardware appropriate for your mounting surface.
5. Tighten set screws and all other screws and hardware. To ensure weatherproof seal, apply weatherproof silicone
sealant to all unused plugs and holes and around the edge of the Wall Plate. Use Teon tape on Arm threads or use
weatherproof silicone sealant between Arm and Swivel Adaptor.
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.
ARMSV24 IN 0712
Door
Arm24
Wall Plate
Housing
Screws (4)
Swivel
Adaptor
LPACK
(not supplied)
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable
parts inside.
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the
Marketing Department at 888-RAB-1000, or email: [e-mail]