RAB Lighting WPLEDC104 User manual

WPLED104 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
WPLED104
Standard (15 Deg)
WPLEDC104
Cuto (7.5 Deg)
WPLEDFC104
Full Cuto (0 Deg)
4.97
[126,3]
4.58
[116,2]
4.97
[126,3]
1.30
[33]
4.58
[116,2]
MOUNTING TO WALL
1. Orient Wall Mounting Box such that ‘TOP’ is pointing
up.
2. Feed supply wires through Gasket and Wall Mounting
Box.
3. Secure Wall Mounting Box to a sturdy wall. Use
appropriate mounting hardware such as lag bolts and
anchors with washers suitable for the mounting surface.
A Leveling Bubble is provided to level xture.
4. Check that Gasket is fully sealed.
5. Slide the stainless steel Tether from the xture into the
Key Hole Slot of the Clip for hands free wiring.
6. Wire the xture using suitable wire connectors.
7. Place wired xture over the Wall Mounting Box and
tighten the Top Screws. Now tighten the Lower
Screws.
8. Tighten Close Up Plugs and apply weatherproof
silicone sealant to all unused conduit entry points. Also
use sealant between the wall and Wall Mounting Box.
Wall Mounting
Box
Top Screws
Lower Screws
Close Up
Plugs (4)
Gasket
Tether
Key Hole Slot
Gasket
Leveling
Bubble
Leveling
Bubble
Clip
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough
to touch. Do not clean or maintain while xture is
energized.
1. Clean glass lens & xture with non-abrasive glass
cleaning solution.
2. Do not open xture to clean the LED. Do not touch the
LED.

WPLED104 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
WIRING
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz. Units ordered with (/480V) sux are 480V.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply
ground.
LIGHT
FIXTURE
(+)LINE BLACK
(-)COMMON WHITE
GROUND GROUND
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly [e-mail]
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
WPLED104 IN 0913
US: pat. D653,377; CN: ZL201130356930.8; MX: 36921; CA: D - RAB Lighting, Inc
WPLED104 Cool WPLED104 Neutral WPLED104 Warm
TROUBLESHOOTING
1. Check that the line voltage at xture is correct.
2. Is there voltage at the lamp xture wires? If there is no
voltage, check all connections.
3. Is the xture grounded properly?
PHOTOCELL INSTALLATION
Photocell may be installed in the eld. Apply weatherproof
silicone sealant to all plugs and unused conduit entries.
1. Remove close up plug on top of the wall mounting box.
2. Install photocell and wire as per diagram.
3. Use photocell rated for your supply voltage.
“COM”
PHOTOCELL
WP2FC
LIGHT
FIXTURE
BLACK
WHITE
PHOTOCELL