RAB Lighting WPLED 78W series User manual

WPLEDTM 78W WALL MOUNT INSTALLATION INSTRUCTIONS
®
Page 1
Thank you for buying RAB lighting fixtures.
Our goal is to design the best quality
products to get the job done right. We’d like
to hear your comments. Call the Marketing
Department at 888-RAB-1000, or email:
market[email protected]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. This product must be installed in accordance with the applicable installation code by a
person familiar with the construction and operation of the product and the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user servicable parts
inside.
MOUNTING ARM ON FIXTURE
1. Remove the Arm Cover from the Arm.
2. Feed wires from Fixture through Gasket into Arm.
3. Line up Arm and Fixture. Place flat washers, lock
washers and nuts on the 3/8-16” bolts inside the Arm
and tighten securely to housing.
4. Make sure the Gasket is secure between Arm and
Fixture.
Screws
Arm
Fixture
3/8” bolts
Gasket
Arm Cover Plugs
Arm 3/8-16 bolts
Gasket
Plugs
Arm Gasket
MOUNTING FIXTURE ON WALL
1. Separate Wall Mount Cover and Wall Mount Box.
2. Orient box so that “TOP” is on top.
3. Secure Wall Mount Box to a sturdy wall. Use
appropriate mounting hardware such as lag bolts and
anchors with washers suitable for the mounting sur-
face. Use weatherproof silicone sealant between wall
and Wall Mount Box.
4. Feed supply wires through Wall Mount Box, Gasket,
and Wall Mount Cover.
5. Check that Gasket between Wall Mount Box and
Wall Mount Cover is secure and screw the cover on
box using four screws.
6. Line up Arm and Wall Mount Cover. Place flat wash-
ers, lock washers and 3/8-16 bolts from wall bracket
(do not use long bolts provided with Arm), inside the
Arm and tighten securely.
7. Feed wires through the Arm Gasket into Arm. Make
necessary connections in the Arm.
8. Replace the Arm Cover. Be sure Gasket on Arm
Cover is in place.
9. Tighten Close Up Plugs and apply weatherproof
silicone sealant to all unused conduit entry points.
Also use sealant between the wall and Wall
Mount Box.
Wall Mount
Cover
Wall Mount Box
Plugs (4)
Tether
Gasket

WPLEDTM 78W WALL MOUNT INSTALLATION INSTRUCTIONS
®
Page 2
4.57”
2.4”
1.09”
.79”
3.0”
TROUBLESHOOTING
1. Check that the line voltage at fixture is correct. Refer
to wiring directions.
2. Is the fixture grounded properly?
3. Is the photocell functioning properly (if used)?
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool
enough to touch. Do not clean or maintain while
fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning
solution.
2. Do not open fixture to clean the LED. Do not touch
the LED.
-*()5
'*9563&
-*/& #-"$,
$0..0/ 8)*5&
(306/% (306/%
WIRING
Universal voltage driver permits operation at 120 to
277VAC, 50 or 60Hz.
1. Connect the black fixture lead to the (+) LINE
supply lead.
2. Connect the white fixture lead to the (-) COMMON
supply lead.
3. Connect the bare copper Ground wire from fixture to
supply ground.
Key Hole Slot
RAB fixture designs are protected under
U.S. and International Intellectual Property laws.
Patent pending.
WALL MOUNT BOX DETAILS
Wall Feed Conduit Feed
Hardware
(not supplied)

WPLEDTM 78W WALL MOUNT INSTALLATION INSTRUCTIONS
®
Page 3
WPLED78 IN 1011
WPLED2T78 Cool WPLED3T78 Cool WPLED4T78 Cool
WPLED2T78 Neutral WPLED3T78 Neutral WPLED4T78 Neutral