RAB Lighting floodinator User manual

FLOODINATORTM INSTALLATION INSTRUCTIONS
®
Page 1
SLIPFITTER MOUNTING
1. The slipfitter fits a 2 3/8” O.D. tenon. Place the
slipfitter over the tenon and secure with the (4) Set
Screws on the side of the slipfitter.
2. To adjust the angle of the fixture:
a. Remove (2) Cover Plate Screws and the
Round Cover Plate.
b. Hold the top of the fixture, loosen the
Locking Bolt and swivel the fixture.
c. Tighten the Locking Bolt and re-attach the
Round Cover Plate.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. This product must be installed in accordance with the applicable installation code by a
person familiar with the construction and operation of the product and the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining fixture.
Thank you for buying RAB lighting
fixtures. Our aim is to design the
best quality products to get the job
done right. We’d like to hear your
comments. Call the Marketing
Department at 888-RAB-1000, or
email: market[email protected]
TRUNNION MOUNTING
1. Mount floodlight to suitable flat surface with adequate
hardware for that surface.
2. To adjust the angle of the fixture:
a. Hold top of fixture, loosen (2) Trunnion
Bolts,the positioning screw and Adjustment
Bolt.
b. Swivel the fixture until positioning screw is in
one of the Positioning Holes.
c. Tighten the Trunnion Bolts, the Positioning
Screw and the Adjustment Bolt.
Locking
Bolt
Set Screws
Round Cover
Plate
Cover Plate
Screws
Trunnion
Bolts
Adjustment
Bolt
Positioning
Holes
.Ø 11/16”
6”
3”
3”

FLOODINATORTM INSTALLATION INSTRUCTIONS
®
Page 2
REFLECTOR ADJUSTMENT
1. Loosen (4) door screws, open door.
2. Push each side of the reflector at point shown
below. The Reflector will lock in position.
3. For even distribution, each side of the reflector
should be adjusted to the same position.
4. Reflectors are factory set at the widest beam,
Position #1.
5. To move reflector back in, gently lift up the reflec-
tor piece with a flat screwdriver. Bend reflector
back and place behind the 1st position stop.
Push Here
Position #2
Shown
Hinge
Hinge
3 Position Stops
Middle Beam
Adjustable Reflector: Patent Pending
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool
enough to touch. Do not clean or maintain while
fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning
solution.
2. As lamps age, light output diminishes. Mass
relamping at regular intervals ensures full light output
at the highest efficiency.
GUARD INSTALLATION
1. Mount GDFN Guard with (4) #10-24 x 3/8” screws as
shown below.
2. Screws are provided with the Guard.
(4) Screws
HOOD INSTALLATION
1. Mount 6” Hood FNH6 or the 12” Hood FNH12
with (4) #10-24 x 3/8” screws as shown below.
2. Screws are provided with the Hood.
(4) Screws
GUARD & HOOD INSTALLATION
The wire guard and the 6” Hood FNH6 or the 12” Hood
FNH12 can be mounted to the same fixture
with (4) #10-24 x 3/8” screws as shown below.
Narrow Beam
Wide Beam
Position #1 Position #2 Position #3

FLOODINATORTM INSTALLATION INSTRUCTIONS
®
Page 3
TROUBLESHOOTING
1. Is the proper lamp is installed? Check the wattage
and ANSI code on the fixture label against markings
on the lamp. Refer to Replacement Lamp table
above for verification.
2. Make sure the lamp is not defective. Try a lamp
known to be in operating condition.
3. Check that the line voltage at fixture is correct. Refer
to wiring directions.
4. Is there voltage at the lamp socket? If there is no
voltage, check all connections.
5. Is the fixture grounded properly?
6. Is the photocell functioning properly (if used)?
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.
FN-IN-0408
REPLACEMENT LAMPS AND
BALLASTS
RAB Lamp ANSI RAB Ballast
Wattage Catalog# Code Catalog#
High Pressure Sodium
400 LHPS400 S51 BHPSH400QT
1000 LHPS1000 S52 BHPSH1000QT
Metal Halide
400 LMH400 M59 BMHH400QT
400PS LMH400PS M155 BMHH400PSQ
1000 LMH1000 M47 BMHH1000QT
480V Ballasts are available, consult factory.
LAMP INSTALLATION
CAUTION: Prior to installing, check that the lamp is
the correct ANSI type and wattage. Observe lamp
manufacturer’s recommendations on lamp operation,
ballast type and burning positions.
1. Disconnect power. Make sure fixture and lamp are
cool enough to touch.
2. Loosen (4) screws from the door of the fixture.
Screws will remain captive to door. Open and
swing door down on hinges.
3. Fully screw lamp into socket.
4. Before closing door, make sure door gasket is
properly seated all around the door.
5. Check that all mounting bolts are tight.
6. Close door. Tighten screws.
ACCESSORIES
Wire Guard: GDFN
6” Hood FNH6
12” Hood FNH12
Factory Installed Photo Cells
120V Swivel /PCS
277V Swivel /PCS2
480V Swivel /PCS4
RAB fixture designs are protected under
U.S. and International Intellectual Property laws.
Patent Pending
WIRING
All units are factory wired for 277V, except for units
with a requested 120V Photocell(“/PC”). If voltages
other than 277V are required, remove ballast cover and
rewire for the appropriate voltage.
1. Connect the black fixture lead to the (+) LINE
supply lead.
2. Connect the white fixture lead to the (-) COMMON
supply lead.
3. Connect the Ground wire from fixture to supply
ground.
4. All unused leads must be capped and insulated.
Supply