RAB Lighting BLED5 Square User manual

BLED5 INSTALLATION INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining
xture. No user servicable parts inside.
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000, or email: [e-mail]
LOCATION
1. The Bollard should be mounted to a rm level
surface.
2. Anchor bolts may be used in new concrete
installations. Use the template provided.
3. For all other applications use anchors suitable for the
mounting surface.
ANCHOR BOLTS INSTALLATION
CAUTION: Install according to all applicable local codes.
1. Install two Anchor Bolts in concrete foundation (by
others) using the template provided. Mounting Plate
may also be used as the template. Anchor Bolts
should protrude no more than 3”.
Concrete
Conduit
Anchor
Bolts
Mounting
Plate
MOUNTING PLATE
Assemble xture(s) to bollard before mounting the Bol-
lard to the Mounting Plate.
1. Place the Mounting Plate over Anchor Bolts.
2. Use four Leveling Screws or shims to level the
Mounting Plate.
3. Tighten assembly using the washers, lockwashers
and nuts provided.
4. Make sure supply leads extend far enough to make
xture connections.
5. Slide Gasket down around the bottom of the
Mounting Plate.
6. Use the four screws to mount the Bollard to the
Mounting Plate. Tighten securely.
Mounting
Plate
Anchor
Bolts
Gasket
Leveling
Screws
Mounting
Screws
Bollard
BLED5 Square BLEDR5 Round BLED2X5 Square BLEDR2X5 Round

BLED5 INSTALLATION INSTRUCTIONS
MOUNTING fIXTURES
For BLED5 & BLEDR5 the window is available on one side of Bollard. Secure Bollard before installing the housing.
1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets.
Fixture may hang from the tether while installing.
2. Place Bollard Gasket and Mounting Plate over recessed box.
3. Attach Mounting Plate with supplied Mounting Plate Screws.
4. Pull supply wires from box through mounting plate and wire xture as shown in the wiring section.
5. Check Housing Gasket. It should remain rmly around the inside of the Housing.
6. Align Housing to Mounting Plate.
7. Make sure all gaskets are properly seated. Tighten Housing Screws.
8. Secure the Cap Gasket and tighten the Bollard Cap with supplied screws.
Bollard
Housing
screws
Bollard
Cap
Cap
Gasket
Housing Mounting
Plate
Bollard
Cap
Cap
Gasket
Bollard
Gasket

BLED5 INSTALLATION INSTRUCTIONS
BLED5-IN-0612
MOUNTING fIXTURES
For BLED2x5 & BLEDR2x5, cutouts are provided on both sides of Bollard. Secure Bollard before installing the
housings.
1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets.
Fixture may hang from the tether while installing.
2. Place Bollard Gasket and Mounting Plate over cut out on Bollard.
3. Attach Mounting Plate with supplied mounting plate screws.
4. Pull supply wires from bollard through mounting plate and wire xture as shown in the wiring section.
5. Check Housing Gasket. It should remain rmly around the inside of the Housing.
6. Align Housing to Mounting Plate.
7. Make sure all gaskets are properly seated. Tighten Housing Screws.
8. Follow same steps for second xture.
9. Secure the Cap Gasket and tighten the Bollard Cap with provided screws.
Bollard
Housing
screws
Bollard
Cap
Cap
Gasket
Housing
Housing
Gaskets
Mounting
Plate
Housing-
Screws
Bollard
Cap
Cap
Gasket
Bollard
Mounting
Plate
Bollard
Gasket
Bollard
Gasket

BLED5 INSTALLATION INSTRUCTIONS
ACCESSORIES
Bollard base: BOLBASE
Bollard base Retro kit: BOLBASE RETRO
Sufx “Y” = Warm 3000K LED
Sufx “N” = Neutral 4000K LED,
WIRING
Universal driver permits 120V to 240V, 50 or 60Hz.
1. Connect the black xture lead to the (+) LINE
supply lead.
2. Connect the white xture lead to the (-) COMMON
supply lead.
3. Connect the bare copper Ground wire from xture to
supply ground.
LIGHT
FIXTURE
(+)LINE BLACK
(-)COMMON WHITE
GROUND GROUND
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool
enough to touch. Do not clean or maintain while
xture is energized.
1. Clean glass lens with non-abrasive glass cleaning
solution
2. Do not open xture to clean the LED.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer
to wiring directions.
2. Is the xture grounded properly?
3. Is the photocell is functioning properly (if used)?
SLED Round: US pat. D612,974, CA Pat. pending,
CN Pat. pending
SLED Square:.US pat. D612,975, CA Pat. pending,
CN Pat. pending
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.
BLED5 Cool LED Square Steplight BLEDR5 Cool LED Round Steplight

BLED5 INSTALLATION INSTRUCTIONS
BLED5Y Warm LED Square Steplight BLEDR5Y Warm LED Round Steplight
BLED5N Neutral LED Square Steplight BLEDR5N Neutral LED Round Steplight

BLED5 INSTALLATION INSTRUCTIONS
ANCHOR BOLT TEMPLATE fOR BLED BOLLARD
Conrm dimensions before using as a template. If possible use the actual mounting plate as your template.