RAB Lighting FALCOR 80W User manual

FALCOR INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
TM
CAUTION
SILICONE ALL PLUGS AND UNUSED CONDUIT ENTRIES FOR WEATHER PROOF SEALING.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
FOR AISLE FIXTURE
1. Loosen the screw connecting Housing Head to Junction
box.
2. Rotate the Housing Head all the way as shown in Fig.1.
3. Tighten the screw.
FIXTURE MOUNTING
Mount Housing to sturdy ceiling structure as follows:
FOR HOOK MOUNTING:
1. V Hooks (2) are provided for chain mounting. Secure
V Hooks through Bracket Hole at back of Housing as in
Fig. 2.
2. Connect to two (2) equal lengths of chain (by others) and/
or appropriate hardware (by others) suitable for mounting
surface, to suspend Housing from V Hooks.
3. Fixture mounting height and spacing should be determined
by application requirements. Use chain suitable to support
four (4) times the weight of the xture (42 lbs).
4. Brackets (2) should be positioned near end of Housing as
shown in Fig.2. Secure Housing to ceiling mounting surface
and adjust Brackets evenly to ensure Housing is stabilized.
5. Unlatch and open the Wiring Box and slide Cord in
Wiring Box. Use approved wiring connectors and wire to
local NEC codes.
FOR PENDANT/ SURFACE MOUNTING:
1. Choose pendant length (3/4” NPS Pendant Stem not
supplied) and feed Cord through pendant stems. If longer
cord is required, replace the Cord with the appropriate length
wires. For wet locations wrap threads on pendant stems with
teon tape and silicone gel. Screw the pendant stem to the
Wiring Box. Tighten set screw.
2. Alternatively, mount Wiring Box to ceiling by drilling out drill
locations. Use the appropriate mounting hardware for the
mounting surface. Be sure gasket is properly seated.
3. Unlatch and open the Wiring Box and slide Cord in
Wiring Box. Use approved wiring connectors and wire to
local NEC codes.
V Hook
Wiring Box
Housing
Pendant
Fig: 1
Screw
Head in Aisle
Position
Junction
Box
FALCOR
80W FALCOR
160W & 230W
FALCOR AISLE
80W FALCOR AISLE
160W & 230W
Bracket
Bracket Hole
Fig: 2
Fig: 3

FALCOR INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
TM
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean glass lens & xture with non-abrasive glass
cleaning solution.
2. Do not open xture to clean the LED. Do not touch the
LED.
WIRING
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz. Units ordered with (/480V) sux are
480V.
1. Connect the black xture lead to the LINE
supply lead.
2. Connect the white xture lead to the COMMON
supply lead.
3. Connect the GROUND wire from xture to
supply ground.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation
operation or maintenance.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer to
wiring directions.
2. Is the xture grounded properly?
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2015 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly [e-mail]
ACCESSORIES
Wire Guard: GDFALCORW
Poly Shield: GDFALCORP
GUARD OR SHIELD INSTALLATION
Wire Guard and Poly Shield mount with (4)
Stainless Steel Screws. Screws are provided with the
accessory. See Fig. 6 for Guard. See Fig. 7 for Shield.
1. Line up guard or shield with existing pre-drilled holes in
frame as shown, tighten screws.
Fig. 6
Fig. 7
Screws (4)
Wire Guard
Housing
Screws (4)
Poly shield
Housing
FALCOR-FALCORA-IN-0915
Fig. 5
0-10V DIMMABLE WIRING
Universal voltage driver permits operation at 120V thru 277V,
50 or 60 Hz. For 0-10V Dimming, follow the wiring directions
as in Fig. 5.
1. Connect the black xture lead to the LINE supply lead.
2. Connect the white xture lead to the COMMON supply
lead.
3. Connect the GROUND wire from xture to supply ground.
Do NOT connect the GROUND of the dimming xture to
the output.
4. Connect the purple xture lead to the (V+) DIM lead.
5. Connect the gray xture lead to the (V-) DIM lead.
6. Cap the yellow xture lead, if present. Do NOT connect.
Fig. 4
WIRING
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz. Units ordered with (/480V) sux are
480V.
1. Connect the black xture lead to the LINE
supply lead.
2. Connect the white xture lead to the COMMON
supply lead.
3. Connect the GROUND wire from xture to
supply ground.