RAB Lighting future flood User manual

FUTURE FLOOD INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
LIGHT
FIXTURE
(+)LINE BLACK
(-)COMMON WHITE
GROUND GROUND
LOCATION
1. Secure the Future Flood to any 1/2” NPS hole in a metal
plate coverplate, junction box or landscape post. Plug all
unused holes and seal threads with silicone.
2. The swivel arm on the Future Flood allows 150º of vertical
aiming adjustment.
3. Do not aim xture to any object closer than 18 inches.
LAMP INSTALLATION
CAUTION: Prior to installing, check that the lamp is
the correct ANSI type and wattage. Observe lamp
manufacturer’s recommendations on lamp operation,
ballast type and burning positions.
1. Disconnect power. Make sure xture and lamp are cool
enough to touch.
2. Remove screw from the door clip on the top of the xture.
Open xture, swing door down on hinges.
3. Fully insert lamp into socket.
4. Before closing door, make sure frame gasket is properly
seated all around the xture.
5. Close door. Replace screw on door clip, if desired.
WIRING
Do not use any supply voltage other than those specied
below:
FF35-FF150 HPS 120V only
FFH50-70 MH 120V only
FF42QT 120V thru 277V*
* No internal wiring changes needed for various voltages as
the ballast is quad tap electronic.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON
supply lead.
3. Connect the bare copper Ground wire from xture to
supply ground.
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough
to touch. Do not clean or maintain while xture is
energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. As lamps age, light output diminishes. Mass relamping at
regular intervals ensures full light output at the highest
eciency.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

FUTURE FLOOD INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
TROUBLESHOOTING
1. Is the proper lamp is installed? Check the wattage and
ANSI code on the xture label against markings on
the lamp. Refer to Replacement Lamp table above for
verication.
2. Make sure the lamp is not defective. Try a lamp known to
be in operating condition.
3. Check that the line voltage at xture is correct. Refer to
wiring directions.
4. Is there voltage at the lamp socket? If there is no voltage,
check all connections.
5. Is the xture is grounded properly?
6. Is the photocell is functioning properly (if used)?
ACCESSORIES AND
REPLACEMENT PARTS
Chrome Wire Guard: GDFF
Door and Frame with Glass: LFF (bronze)
LFFW (white)
Swivel Arm: FFLARMA (bronze)
FFLARMW (white)
Factory Installed Photocell: “/PC” (120V)
“/PC2” (277V)
“/PCS” (Swivel 120V)
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
FF-IN-0113
GUARD INSTALLATION
1. Slide top and bottom ends of one side of guard into
notches in the door frame.
2. Squeeze guard and slide the other ends of the guard into
notches on the opposite side of the frame.
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2012 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly [e-mail]
REPLACEMENT LAMPS AND BALLASTS
Lamp ANSI Ballast
Wattage Catalog# Code Catalog#
High Pressure Sodium
35 LHPS35 S76 BHPSN35
50 LHPS50 S68 BHPSN50
70 LHPS70 S62 BHPSN70
100 LHPS100 S54 BHPSN100
150 LHPS150 S55 BHPSN150
Metal Halide
50 LMH50 M110 BMHN50
70 LMH70 M98 BMHN70
Compact Fluorescent Base Type
42 LCFL42 GX24q-4 BCLF42