RADLEY 1281-914 User manual
1281-914
Onr’s Mna
READ ALL INSTRUCTIONS BEFORE FIRST USE.
KEEP THIS MANUAL FOR FUTURE REFERENCE.
KEEP AWAY FROM CHILDREN.
WEAR A
FACE MASK
WEAR EAR
PROTECTION
WEAR CSA APPROVED
EYE PROTECTION
35
120V • 60
LISTED
61TN
E213739
JD3315U
1
Rtr ol Kt - Onr's Mna
PRODUCT SPECIFICATIONS
Rating: 120 V, 60 Hz AC
Amperes: 1.2 A
Need Assistance?
•
•
•
2
1281-914
TABLE OF CONTENTS
………….……………………………………………………………1
………….……………………………………………………………2
………………….…………………………………………………….6
………….……………………………………………………………6
………….……………………………………………………………10
………….……………………………………………………………11
………….……………………………………………………………12
………….……………………………………………………………16
Rtr ol Kt - Onr's Mna
GENERAL SAFETY WARNINGS
WARNING:
This instruction manual includes the following:
EYE, EAR & LUNG PROTECTION
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CSA
REQUIREMENTS or ANSI SAFETY STANDARD Z87.1
WARNING:
ALWAYS WEAR EAR PROTECTION
WARNING:
WEAR A DUST MASK THAT IS DESIGNED TO BE USED WHEN OPERATING A
POWER TOOL IN A DUSTY ENVIRONMENT.
WARNING:
•
•
•
•
•
•
WEAR A
FACE MASK
WEAR EAR
PROTECTION
WEAR CSA APPROVED
EYE PROTECTION
1281-914
ELECTRICAL SAFETY
WARNING:
POWER TOOL SAFETY
WARNING: Read all safety warnings and instructions
Save all warnings and instructions for future reference.
WORK AREA SAFETY
Keep work area clean and well lit.
Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust.
Keep children and bystanders away while operating a power tool.
•
•
•
WEAR A
FACE MASK
Rtr ol Kt - Onr's Mna
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Avoid body contact with earthed or grounded surfaces such as pipes, radi-
ators, ranges and refrigerators.
Do not expose power tools to rain or wet conditions.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication.
Use personal protective equipment. Always wear eye protection.
Prevent unintentional starting. Ensure the switch is in the o-position before
connecting to power source and/or battery pack, picking up or carrying the
tool.
Remove any adjusting key or wrench before turning the power tool on. A
6
1281-914
Do not overreach. Keep proper footing and balance at all times.
Dress properly. Do not wear loose clothing or jewelery. Keep your hair,
clothing and gloves away from moving parts.
If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool for your application.
Do not use the power tool if the switch does not turn it on and o
Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools.
Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may aect the power tool’s
operation. If damaged, have the power tool repaired before use.
Keep cutting tools sharp and clean.
Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to
be performed.
Service
Have your power tool serviced by a qualified repair person using only identical
replacement parts.
Rtr ol Kt - Onr's Mna
SPECIFIC SAFETY RULES
WARNING: Know your rotary tool. Do not plug the tool into the power
source until you have read and understand this Instruction Manual. Learn
the tool’s applications and limitations, as well as the specific potential
hazards related to this tool.
WARNING:
Hold tool by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring or its own cord.
Always make sure the work surface is free from nails and other foreign objects.
Never hold the workpiece in one hand and the tool in the other hand when in
use. Never place the hands near or below the cutting surface.
Never lay workpiece on hard surfaces like concrete, stone, etc.
Always wear safety goggles and dust mask. Use only in well-ventilated area.
After changing the bits and accessories or making adjustments, make sure the
collet nut and any other adjustment devices are securely tightened.
Always use the correct collet size.
Always check accessory bits, grinding stones, cut-o wheels etc. for damage
before each use.
Never use dull or damaged bits. Sharp bits must be handled with care.
WEAR CSA
APPROVED
EYE PROTECTION
1281-914
Never touch the bit during or immediately after use.
During this initial run-up,
always wear a face shield and make sure you are NOT in line with the rotating
accessory to avoid injury caused by flying debris.
GUIDELINES FOR EXENSION CORDS
WARNING: Repair or replace damaged or worn extension cords immediately.
WARNING: Keep the extension cord clear of the working area. Position the
cord so it will not get caught on the workpiece, tools or any other obstructions
while you are working with the power tool.
Rtr ol Kt - Onr's Mna
V s
A Amperes
Hz Hertz
W Watts
s
s
H s
2
eter
Pa s
OPM e
Min s
S s
.ternating
Threng
ent
Thre
t
Watertight
trti
gr
termin
,
e
Warn
s
LISTED
61TN
E213739
JD3315U
SYMBOLS
WARNING:
10
1281-914
KNOW YOUR ROTARY TOOL
Air vents
Hanging
t
h
s
11
Rtr ol Kt - Onr's Mna
12
1281-914
ACCESSORY DESCRIPTION & USE
NOTE:
NOTE: This Radley Rotary Tool is compatible with most accessories and
attachments provided by other leading brands.
Rtr ol Kt - Onr's Mna
ASSEMBLY AND OPERATING
VARIABLE SPEED CONTROL WHEEL
ON/OFF SWITCH
CHANGING THE COLLET
NOTE:
WARNING:
NOTE:
Fig. 1
Fig. 2
Fig. 3
1281-914
ASSEMBLY AND OPERATING
INSTALLING ACCESSORIES
NOTES:
NOTE:
WARNING:
During this
initial run-up, always wear a face shield and
make sure you are NOT in line with the rotating
accessory to avoid injury caused by flying debris.
SELECTING PROPER SPEEDS
Fig. 4
For safety reasons, the operator must read
the sections of this Owner’s Manual entitled
"GENERAL SAFETY WARNINGS", "POWER
TOOL SAFETY", "SPECIFIC SAFETY
RULES", "EXTENSION CORD SAFETY" and
"SYMBOLS" before using this rotary tool.
Verify the following every time the rotary
tool is used:
1. Safety glasses, safety goggles, or face
shield are being worn.
2. Accessory is in good condition and not
damaged in any way.
3. Workpiece is properly secured.
Failure to observe these safety rules will
significantly increase the risk of injury.
WARNING
!
OPERATION
SPEED
Cutting metal
5–MAX
Sanding wood
5–MAX
Cutting hard metal
5–MAX
Engraving metal
4–5
De-burring
4–5
Drilling holes
4–5
Removing rust
3–4
Sharpening
3–4
Polishing
1–2
Rtr ol Kt - Onr's Mna
MAINTENANCE
GENERAL
LUBRICATION
REPLACING THE CARBON MOTOR BRUSHES
Fig. 5
NOTE: Make sure the brush cap
threads are not cross threaded. Do NOT
over tighten.
Repeat steps #1 to #4 and replace the
second carbon brush located on the
opposite side of the motor housing.
16
1281-914
Rtr ol Kt - Onr's Mna
PARTS LIST
WARNING: When servicing, use only original equipment replacement parts. The use of any
other parts may create a safety hazard or cause damage to the rotary tool.
Any attempt to repair or replace electrical parts on this rotary tool may create a safety
hazard unless repairs are performed by a qualified technician. For more information, call the
Toll-free Helpline, at 18663498665.
Always order by PART NUMBER, not by key number.
1281-914
WARRANTY
RADLEY ROTARY TOOL KIT WARRANTY
1281-914
MADE IN CHINA / FABRIQUÉ EN CHINE
HOME HARDWARE STORES LIMITED
ST. JACOBS, ONTARIO N0B 2N0
ORDER ONLINE / COMMANDE EN LIGNE
EXCLUSIVE TO HOME HARDWARE
For information on the entire line-up of Radley power
tools visit homehardware.ca or your local Home Hardware retail store.
© 07 / 2019 Home Hardware Stores Limited
120V • 60
35
Table of contents
Other RADLEY Power Tools manuals
Popular Power Tools manuals by other brands
TE Connectivity
TE Connectivity Micro-MaTch 528405-9 instruction sheet
Trumpf
Trumpf TruTool TF 350 Operator's manual
Worx
Worx WT463 Original instructions
HSM
HSM FP 1500 operating instructions
Chicago Electric
Chicago Electric 41053 Set up and operating instructions
ooznest
ooznest WorkBee CNC Assembly instructions
Ingersoll-Rand
Ingersoll-Rand LUB5130 user manual
Bosch
Bosch Professional GWX 15-125 PS Original instructions
Milwaukee
Milwaukee HEAVY DUTY M12 BLROT user manual
Pace
Pace PS-90 Operation and maintenance manual
MULTIQUIP
MULTIQUIP Mikasa MVH-402DSB Operation and parts manual
Ingersoll-Rand
Ingersoll-Rand MX60 Product information
