RAIS Visio 70 F User manual

1
Arranging ceramic logs - Visio 70 F, LC/RC & 3S
It is very important that you follow this when positioning ceramic “logs” and the
 emberslayerinthereplace.Failuretocarrythisoutcorrectlywillcausethereplace
 tonotburnoptimallyandsoottooccur.
OPSTILLINGSAFSTANDE
ARRANGING CERAMIC ”LOGS” - VISIO 70 F, LC/RC & 3S

2
OPSTILLINGSAFSTANDE – OVN MED DREJEFOD
IMPORTANT INFORMATION: CERAMIC “LOGS” AND THE EMBERS LAYER
NB!
The measurements on the following photos are taken from the edge of the base plate.See
photobelow.
cmcm
Important information: Ceramic “logs” and the embers layer
When arranging ceramic “logs” and the embers layer in the combustion chamber, it is important
that they do not cover the pilot ame and its thermocouple, and ember material must not be
placed under the pilot guard.Boththermocouplesmustbekeptfreeoftheemberslayer.
Donotcovertheholesinthemainburner(shownbytheredcircles).
  Pilotame  Secondthermocoupleforthemainburner
NB!
Please note that there should be a small intermediary space between the “logs” that lie on
theburnersandbetweenthesurroundinglogs,sothereisspacefortheamesinbetween
them.Ifthereisnotspacefortheames,thereplacewillnotburnoptimallyandsootmay
form.

3
OPSTILLINGSAFSTANDE – OVN MED DREJEFOD
1. Startbypositioning logno.4(1cmfromthebackwall)asshowninthepicture.
123456
Visio 70 F, LC/RC & 3S
Youwillndtheseceramiclogsinthepackage:
Procedure:
ARRANGING CERAMIC ”LOGS” AND EMBERS
NB! Should not be
used for this model
417 cm17 cm

4
ARRANGING CERAMIC ”LOGS” AND EMBERS
2. Nowsecurethetwoburnersinthereplace’sbaseplate.
3.  Positionlogno.6asshowninthepicture.
6
11 cm11 cm
5 cm5 cm
1 cm1 cm
NB! Fornatural gas and city gas please position the
secondary burners as described in the installation manual
onpage28.
ForLPG gas the secondary burners are delivered with two
rowsofholes,andcanbeplacedasbothrightandleftburner.

5
ARRANGING CERAMIC ”LOGS” AND EMBERS
4.  Positionlogno.5asshowninthepicture.
5. Positionlogno.1(withtherecess)overtherightburner.
5
1
4 cm4 cm
5 cm5 cm

6
ARRANGING CERAMIC ”LOGS” AND EMBERS
6.  Positionlogno.2(withtherecess)overtheleftburner.
2
7. Nowtheglassstonesshouldbespreadoutinthegasreplace.Meassureout8dlofglass
stonesinameassuringcup.

7
ARRANGING CERAMIC ”LOGS” AND EMBERS
8. Spreadouttheglassstones(8dlintotal)inthegasreplace-overtheLEDlights.Itisimpor-
tant that the glass stones are spread out in a thin layer that covers the holes in the bottom of
thereplace.
9. Nowmeassureout1,5lofembers(amixofthegreyandblackchips).

8
ARRANGING CERAMIC ”LOGS” AND EMBERS
10. Spreadtheembers acrossboththeglassstonesandthebaseplatewiththeholes.
Placethelamentsonthepilotarea.
11. Ensurethatlogno.5andlogno.6donottouchlogno.1andlogno.2.Thereshouldbe
spacebetweenthem.
NB! Itisextremelyimportantthat
you do not cover the pilot area and
the holes there(seepage2).
12. Mounttheglassagain.
ScantheQRcodetoseeavideoofhowtomounttheglass.

9
ARRANGING CERAMIC ”LOGS” AND EMBERS