RAIS Visio 90 F User manual

1
Arranging ceramic logs - Visio 90 F, LC/RC & 3S
It is very important that you follow this when positioning ceramic “logs” and the
 emberslayerinthereplace.Failuretocarrythisoutcorrectlywillcausethereplace
 tonotburnoptimallyandsoottooccur.
OPSTILLINGSAFSTANDE
ARRANGING CERAMIC ”LOGS” - VISIO 90 F, LC/RC & 3S

2
Important information: Ceramic “logs” and the embers layer
When arranging ceramic “logs” and the embers layer in the combustion chamber, it is important
that they do not cover the pilot ame and its thermocouple, and ember material must not be
placed under the pilot guard.Boththermocouplesmustbekeptfreeoftheemberslayer.
Donotcovertheholesinthemainburner(shownbytheredcircles).
  Pilotame  Second thermocouple for the main burner
OPSTILLINGSAFSTANDE – OVN MED DREJEFOD
IMPORTANT INFORMATION: CERAMIC “LOGS” AND THE EMBERS LAYER
NB!
Please note that there should be a small intermediary space between the “logs” that lie on
theburnersandbetweenthesurroundinglogs,sothereisspacefortheamesinbetween
them.Ifthereisnotspacefortheames,thereplacewillnotburnoptimallyandsootmay
form.
NB!
Themeasurementsonthefollowingphotosaretakenfrom the edge of the base plate.See
photobelow.
cmcm

3
OPSTILLINGSAFSTANDE – OVN MED DREJEFOD
1. Startbysecuringtwoburnersinthereplace’sbaseplate.
123456
Visio 90 F, LC/RC & 3S
Youwillndtheseceramiclogsinthepackage:
Procedure:
ARRANGING CERAMIC ”LOGS” AND EMBERS
Note the small bump
on the right side
NB! Fornatural gas and city gas please position the
secondary burners as described in the installation manual
onpage28.
ForLPG gas the secondary burners are delivered with two
rowsofholes,andcanbeplacedasbothrightandleftburner.

4
ARRANGING CERAMIC ”LOGS” AND EMBERS
2. Positionlogno.6asshownintheimage.
3.  Positionlogno.5asshownintheimage.
6
5
15 cm15 cm
26 cm26 cm
22 cm22 cm
11 cm11 cm
29 cm29 cm

5
ARRANGING CERAMIC ”LOGS” AND EMBERS
4. Fromtheoppositesidelogno.4ispositionedasshownintheimage.
5. Thenpositionlogno.3restingonlogno.4asshownintheimage.
4
3
17 cm17 cm
2 cm2 cm
5 cm5 cm
1 cm1 cm
8 cm8 cm
18 cm18 cm

6
ARRANGING CERAMIC ”LOGS” AND EMBERS
6. Nowtheglassstonesshouldbespreadoutinthegasreplace.Meassureout8dlofglass
stonesinameassuringcup.
7. Spreadouttheglassstones(8dlintotal)oneachsideofthegasreplace-overtheLED
lights.Itisimportantthattheglassstonesarespreadoutinathinlayerthatcoverstheholes
inthebottomofthereplace.

7
ARRANGING CERAMIC ”LOGS” AND EMBERS
8. Nowmeassureout2,5lofembers(amixofthegreyandblackchips).
9. Spreadtheembers acrossboththeglassstonesandthebaseplatewiththeholes.
Placethelamentsonthepilotarea.
NB! Itisextremelyimportantthat
you do not cover the pilot area and
the holes there(seepage2).

8
ARRANGING CERAMIC ”LOGS” AND EMBERS
10. Positionlogno.1(withtherecess)overtherightburner.
11. Positionlogno.2(withtherecess)overtheleftburner.
1
2

9
ARRANGING CERAMIC ”LOGS” AND EMBERS
12. Ensurethatlogno.3andlogno.6donottouchlogno.1andlogno.2.Thereshouldbe
spacebetweenthem.
13. Mounttheglassesagain.
ScantheQRcodetoseeavideoofhowtomounttheglass.